Yep, that was it. QoS was enabled with a 10Mb link limit. Disabling that gets me back to similar performance to the gateway for speedtest and ping (is this a default with the new build?).
Not sure this would account for some of the slowness that seemed to be happening last night to my HASS box but will keep an eye on it over the weekend and see if anything crops up. I’ve also uninstalled the adblock plugin for the moment just to reduce potential variables.
Time based restrictions using UMT not local?
Moderator: Moderators
Re: Time based restrictions using UMT not local?
WNDR3800 Gargoyle v1.11
D-Link DIR-868L (wifi access point, standard DLink software)
D-Link DIR-868L (wifi access point, standard DLink software)
Re: Time based restrictions using UMT not local?
Ok, ran it for 24 hours with no problems then reinstalled and reenabled the adblock plugin. After which had trouble connecting to internet or even the router. I suspect there may be a compatibility issue between the new build and adblock plugin. Even after uninstalling it again the router response via the web interface is very flaky and sluggish
WNDR3800 Gargoyle v1.11
D-Link DIR-868L (wifi access point, standard DLink software)
D-Link DIR-868L (wifi access point, standard DLink software)
Re: Time based restrictions using UMT not local?
factory reset?
start again?
start again?
Re: Time based restrictions using UMT not local?
If you have a problem with AdBlock, please read this post first: viewtopic.php?f=14&t=11829&start=160#p52151
AdBlock takes a lot of system resources, so be careful.
AdBlock takes a lot of system resources, so be careful.
Turris Omnia with OpenWrt 21.02 - Tested
Linksys WRT3200ACM with Gargoyle 1.13.x
TL-WR1043ND v2 with Gargoyle 1.10.0
http://gargoyle.romanhk.cz custom builds by gargoyle users
Linksys WRT3200ACM with Gargoyle 1.13.x
TL-WR1043ND v2 with Gargoyle 1.10.0
http://gargoyle.romanhk.cz custom builds by gargoyle users
Re: Time based restrictions using UMT not local?
Did a reflash back to the development version but still getting some dropouts where the web interface comes up as page not found when navigating between screens.
Reflashed again back to the release version of 1.11 and it seems to be stable and a lot more responsive. I had been running adblock on 1.11 before the timezone issue without any apparent problems.
At the moment memory use is at 19% and processor load is at zero. Haven't been game to reinstall adblock - had enough excitement this weekend
Reflashed again back to the release version of 1.11 and it seems to be stable and a lot more responsive. I had been running adblock on 1.11 before the timezone issue without any apparent problems.
At the moment memory use is at 19% and processor load is at zero. Haven't been game to reinstall adblock - had enough excitement this weekend

WNDR3800 Gargoyle v1.11
D-Link DIR-868L (wifi access point, standard DLink software)
D-Link DIR-868L (wifi access point, standard DLink software)
Re: Time based restrictions using UMT not local?
which version?Did a reflash back to the development version
Re: Time based restrictions using UMT not local?
The one i had already downloaded.
Gargoyle Version:1.11.X (Built 20190426-2024 git@ddc7c0ba)
Gargoyle Version:1.11.X (Built 20190426-2024 git@ddc7c0ba)
WNDR3800 Gargoyle v1.11
D-Link DIR-868L (wifi access point, standard DLink software)
D-Link DIR-868L (wifi access point, standard DLink software)