Ubiquiti BulletM2 lost password

General discussion about Gargoyle, OpenWrt or anything else even remotely related to the project

Moderator: Moderators

ispyisail
Moderator
Posts: 5194
Joined: Mon Apr 06, 2009 3:15 am
Location: New Zealand

Re: Ubiquiti BulletM2 lost password

Post by ispyisail »

https://openwrt.org/toh/ubiquiti/bullet
To flash an already running bullet with original firmware (AirOS) on CLI, you must do this:

or
Firmware Install Ubnt Recovery Method
If you prefer TFTP, than you can update via holding down the reset-button for 10 seconds on startup, and send the firmware to 192.168.1.20
See →generic.flashing or →generic.flashing.tftp for instructions.

http://wiki.ubnt.com/Firmware_Recovery

ispyisail
Moderator
Posts: 5194
Joined: Mon Apr 06, 2009 3:15 am
Location: New Zealand

Re: Ubiquiti BulletM2 lost password

Post by ispyisail »

It can be done, you just need the patience and desire

ispyisail
Moderator
Posts: 5194
Joined: Mon Apr 06, 2009 3:15 am
Location: New Zealand

Re: Ubiquiti BulletM2 lost password

Post by ispyisail »

Just a note
re:Firmware Install Ubnt Recovery Method

These instructions leave out very basic information

e.g.
You need to run a good known Ethernet cable directly between M2 and PC.

(You don't know how many times people have used damaged cables)

You need to fix the IP address on your PC

192.168.1.2
255.255.255.0

Image

You can use other address but if you don't know why just use the one above.

top_s
Posts: 37
Joined: Mon Aug 13, 2018 10:09 pm
Location: Brazil

Re: Ubiquiti BulletM2 lost password

Post by top_s »

bowsprit wrote:Yes indeed, it has a reset button, but it seems to have no effect on resetting the gargoyle software.
I tried every procedure and combination, i could find online to reset, but no luck there.
It may work if it had ubiquiti firmware installed, I guess..?
1. Have you tried starting the router while holding reset buttom for like 10s before power on and 20s after power on?

2. Have you tried the default gargoyle password, witch is password?
WDR4300 v1 (stock)
WR941nd v2 (1.9.2)
WA901nd v2 (1.6.2)
2x WR741nd (1.6.2)

(Up to) 1gbps up/down link

bowsprit
Posts: 17
Joined: Fri Dec 28, 2018 3:44 pm

Re: Ubiquiti BulletM2 lost password

Post by bowsprit »

Thanks for your reply
1) yes and a few more suggestions . none seem to work
2) yes and a whole lot more pw's

ispyisail
Moderator
Posts: 5194
Joined: Mon Apr 06, 2009 3:15 am
Location: New Zealand

Re: Ubiquiti BulletM2 lost password

Post by ispyisail »

This is the official procedure

https://help.ubnt.com/hc/en-us/articles ... e-Recovery
Press the reset button on the device. While holding the reset button down, power the unit on. Wait 8 seconds then release the button (if you want to reset the unit to factory defaults, wait about 15 seconds or until the signal LEDs light up to indicate that the device is ready for recovery).

ispyisail
Moderator
Posts: 5194
Joined: Mon Apr 06, 2009 3:15 am
Location: New Zealand

Re: Ubiquiti BulletM2 lost password

Post by ispyisail »

This procedure is fool prof unless the hardware is damaged.

bowsprit
Posts: 17
Joined: Fri Dec 28, 2018 3:44 pm

Re: Ubiquiti BulletM2 lost password

Post by bowsprit »

I have tried this " TFTP recovery " procedure over the last 2 days a number of times . It was in fact the reason I came to this forum.
Everytime I get " Connect request failed" And YES, TFTP is enabled in Win 10 and Win 7.
The reason WHY laptop in not "seeing" the router remains unclear. i tried it on 2 laptops Everytime the same reply" "connection failed" ??
I read somewhere that TFTP recovery is only valid for files
<3GB.
Yet the firmware update bins are 6 to 7GB+
Maybe that is the reason for connection failure?
I can see the Bullet receiving incoming data in "Networx v5.4.2" free from Softperfect ( hence i presume the hardware is not faulty)

Lantis
Moderator
Posts: 6920
Joined: Mon Jan 05, 2015 5:33 am
Location: Australia

Re: Ubiquiti BulletM2 lost password

Post by Lantis »

Firmware files are in the range of 4-20MB, not gigabytes. What are you trying to send it...?
https://lantisproject.com/downloads/gargoylebuilds for the latest releases
Please be respectful when posting. I do this in my free time on a volunteer basis.

bowsprit
Posts: 17
Joined: Fri Dec 28, 2018 3:44 pm

Re: Ubiquiti BulletM2 lost password

Post by bowsprit »

Yes. you are right. Spelling mistake.. Read MB instead of GB.
Either way, It won't connect. You got any ideas why??

Post Reply