vplessky: I've tested with two TP-link ar71xx models, though not the one you have and have not encountered this problem. By any chance are you using PPPoE? There's another thread in the forum reporting some errors with AR71xx when PPPoE is in use, and I am wondering if there's any chance this might be related.
SVoyager: I haven't actually tested on the model you refer to, though wireless seems to be working properly on the models I do have available to test with. I may not be able to address what's going on without having one of these to play with. However, I might be able to figure out the problem if you could copy/paste the web page source code from your browser when viewing the connection/basic page after you've enabled wireless (but it isn't being displayed properly) into this forum or into a PM to me. Note that this will include your wireless password, so you might want to set it to something you don't normally use before copy/pasting this code.
Version 1.3.8
Moderator: Moderators
Re: Version 1.3.8
PM sent, so to not fill this place with code.
Thanks!
Thanks!
Re: Version 1.3.8
Yes, I have PPPoE connection with my provider.Eric wrote:vplessky: I've tested with two TP-link ar71xx models, though not the one you have and have not encountered this problem. By any chance are you using PPPoE? There's another thread in the forum reporting some errors with AR71xx when PPPoE is in use, and I am wondering if there's any chance this might be related.
I also tested Static IP. Same problem.
I can ping www.google.com from router CLI, and I can't ping www.google.com from PC connected to router.
There were some reports that changing Mac address on WAN connection may cause such problems. But that OpenWrt ticket has been closed, sO I guess it has been fixed.
Re: Version 1.3.8
Very nice update but the "connections" on overview is blank on my g300nh.
OpenWrt 10.03.1-rc4 is out with lots of fixes, hope the next build is based off it.
OpenWrt 10.03.1-rc4 is out with lots of fixes, hope the next build is based off it.
Re: Version 1.3.8
You mean -sco77 wrote:Very nice update but the "connections" on overview is blank on my g300nh.
Connections: 0/4096
on Overview (Status) page?
Can you connect to Internet?
If not - see my posts above.
Connection to Internet via PPPoE doesn't work for me.
Re: Version 1.3.8
I did "clean test", to make sure that problem is not coming from provider's side.
Network layout
-------------------------
Internet -- [router 192.168.1.1] --- [Gargoyle 10.10.10.1] --- Client PC
Gargoyle (WR841ND)
LAN IP: 10.10.10.1
WAN settings:
WAN IP: 192.168.1.10 (Static IP)
Mask: 255.255.255.0
Gateway: 192.168.1.1
Custom DNS server: 192.168.1.1
Client PC:
IP: 10.10.10.50/24
Gateway: 10.10.10.1
DNS: 10.10.10.1
NOTE: I have not changed my WAN address on Gargoyle router (yet), for this setup.
Packets are coming through router just fine.
I can access Internet and resources on 192.168.1.x LAN.
So it seems problem can be indeed related to PPPoE.
Or to Mac address cloning.
Network layout
-------------------------
Internet -- [router 192.168.1.1] --- [Gargoyle 10.10.10.1] --- Client PC
Gargoyle (WR841ND)
LAN IP: 10.10.10.1
WAN settings:
WAN IP: 192.168.1.10 (Static IP)
Mask: 255.255.255.0
Gateway: 192.168.1.1
Custom DNS server: 192.168.1.1
Client PC:
IP: 10.10.10.50/24
Gateway: 10.10.10.1
DNS: 10.10.10.1
NOTE: I have not changed my WAN address on Gargoyle router (yet), for this setup.
Packets are coming through router just fine.
I can access Internet and resources on 192.168.1.x LAN.
So it seems problem can be indeed related to PPPoE.
Or to Mac address cloning.
Re: Version 1.3.8
I meant just the number of port connections but it started working now.vplessky wrote:You mean -sco77 wrote:Very nice update but the "connections" on overview is blank on my g300nh.
Connections: 0/4096
on Overview (Status) page?
Can you connect to Internet?
If not - see my posts above.
Connection to Internet via PPPoE doesn't work for me.
Re: Version 1.3.8
same here on TL-WR1043ND , "Connections" is blank on Overview page, nothing is displayed there. also checked that when I put "cat /proc/net/ip_conntrack | wc -l" in ssh console it shows number of connections in console.
Probable bug
In english is fine, but make some problems in other versions.
http://eko.one.pl/openwrt/sources/port_forwarding.patch
I must also check the other call getSelectedValue.
Also - in forward_single_edit, if I do refresh (Ctrl-R), the buttons disappear.
http://eko.one.pl/openwrt/sources/port_forwarding.patch
I must also check the other call getSelectedValue.
Also - in forward_single_edit, if I do refresh (Ctrl-R), the buttons disappear.
Re: Version 1.3.8
in 1.3.8 it's no LAN <> WAN traffic allowed.
I've repeated settings again as here
WR1043ND - no routing or packet forwarding LAN->WAN ?
I've repeated settings again as here
WR1043ND - no routing or packet forwarding LAN->WAN ?