TL-WR1043ND - Repeater

[tjotabe]

Hi

I would appreciate your help on the following issue. I'm trying to use TP LIN WR1043N V3 as repeater for two netwoks (not at the same time).
I sucessfully installed the gargoyle 1.9.1 but I'm not able to identify what are the configurations (marked as >) in order to repeate them:

Device Configuration
Configure Device As:
>Wireless Bridge/Repeater

Wireless Bridge/Repeater

>Bridge IP: ?
>Subnet Mask: 255.255.255.0
>AP/Gateway IP: ?
>Wan Ethernet Port: Disable ?
>DNS Servers: Use gatewas as DNS Server ?

Connect Via Client Bridge


NETWOR NUMBER 1:

Code: Select all

  Description . . . . . . . . . . . : Intel(R) Centrino(R) Advanced-N 6205
  Physical Address. . . . . . . . . : 
  DHCP Enabled. . . . . . . . . . . : Yes
  Autoconfiguration Enabled . . . . : Yes
  Link-local IPv6 Address . . . . . : fe80::2d23:9961:84cd:af42%12(Preferred)
  IPv4 Address. . . . . . . . . . . : 192.168.8.102(Preferred)
  Subnet Mask . . . . . . . . . . . : 255.255.255.0

  Default Gateway . . . . . . . . . : fe80::e2a3:acff:feb0:5707%12
                                      192.168.8.1
  DHCP Server . . . . . . . . . . . : 192.168.8.1

  DNS Servers . . . . . . . . . . . : fe80::e2a3:acff:feb0:5707%12
                                      192.168.8.1
                                      192.168.8.1
  NetBIOS over Tcpip. . . . . . . . : Enabled

NETWORK NUMBER 2:

Code: Select all

   Description . . . . . . . . . . . : Intel(R) Centrino(R) Advanced-N 6205
   Physical Address. . . . . . . . . : 
   DHCP Enabled. . . . . . . . . . . : Yes
   Autoconfiguration Enabled . . . . : Yes
   Link-local IPv6 Address . . . . . : fe80::2d23:9961:84cd:af42%12(Preferred)
   IPv4 Address. . . . . . . . . . . : 10.15.190.179(Preferred)
   Subnet Mask . . . . . . . . . . . : 255.255.0.0

   Default Gateway . . . . . . . . . : 10.15.0.1
   DHCP Server . . . . . . . . . . . : 10.102.88.4

   DNS Servers . . . . . . . . . . . : 88.214.178.1
                                       88.214.178.2
   NetBIOS over Tcpip. . . . . . . . : Enabled

[d3fz]

There's a how-to guide in the documentation:

http://www.gargoyle-router.com/wiki/dok ... nt_ap_mode

The only difference is that your repeater/bridge subnet MUST be OUTSIDE the AP subnet.

E.g.

AP Subnet 192.168.1.X
Bridge Subnet 192.168.2.X

[nynjardin]

Hi,

How to make them to comunicate with each other?

Because I have my network with some computer connected to my internet router and I want to connect some other computer to the same lan, via wifi (I don't have a long enough cable), so I use gargoyle on my Archer C7. Installation work fine, all my network have access to internet, but the computer connected to my internet router can't connect to all computer connected to gargoyle...

How to make it work?

Thank you!

[ericwong]

Looks like the reason is because you have them in a different subnet. Just put them under the same subnet and they will be able to talk to each other, i.e. you need to disable DHCP in your repeater.