Gargoyle on D-Link DIR-300

[ispyisail]

If you had a wiki i would write a documented procedure for installing gargoyle on a dir-300.

Did i say a big thanks

If you want me to do some testing or anything, I'm your man

[ispyisail]

Had my first play with gargoyle

very cool

[ispyisail]

I've just tested your new version with vista without c++ installed

Still doesn't work

fon flash.png (234.05 KiB) Viewed 20091 times

[Eric]

You forgot to install WinPcap. That's still a dependency....

[ispyisail]

oops

I should have read the message box

[ispyisail]

windows vista, without c++ install, with winpcap

fon flash2.png (133.96 KiB) Viewed 20077 times

[ispyisail]

I can confirm with windows xp (same machine) I can flash both gargoyle (fon version) and dd-wrt (dir-300 verson) onto a "d-link dir-300"

Windows 2000 also tested working but machine had c++ installed so i can't confirm that side of things.

its easy now

[swisskomputer]

Great tool, I was sooo happy when I found it.

Is it possible to install Gargoyle using a Linux o Mac OSX machine, and what would the right steps for this be?

I see instructions for Windows, but not for LINUX or OSX.

Thanks in advance for your response.

Regards,

Jacob

[ispyisail]

Im not sure of the current status but unless Eric has uploaded new version of fon flash you will need to compile your own version from the source. see wiki and there is a thread on the fourm

[Quarbe]

Hi all!

I´ve tried, and tried, but no sucess.

I´m thinking about the hardware, my DIR-300 is:

P/N: EIR300EEU...A1G
H/W Ver.: A1 F/W Ver.: 1.04

It´s running ddwrt... ap61.ram loaded.

Next step is fis init, set ip address, load ap61.rom, fis create etc etc.

But fis init says diferent memory, lets go:

My router:
DD-WRT> fis init
About to initialize [format] FLASH image system – continue (y/n)? y
*** Initialize FLASH Image System
… Erase from 0xbffe0000-0xbfff0000: .
… Program from 0×80ff0000-0×81000000 at 0xbffe0000: .

Original post:
DD-WRT> fis init
About to initialize [format] FLASH image system – continue (y/n)? y
*** Initialize FLASH Image System
… Erase from 0xbfc30000-0xbffe0000: …………………………………………………..
… Erase from 0xbffe0000-0xbfff0000: .
… Program from 0×80ff0000-0×81000000 at 0xbffe0000: .

My router:
DD-WRT> ip_address -h 192.168.1.2
IP: 192.168.1.1./255.255.255.0, Gateway: 0.0.0.0
Default server: 192.168.1.2

Original post:
DD-WRT> ip_address -h 192.168.1.2
Default server: 192.168.1.23

My router:
DD-WRT> load -r -b %{FREEMEMLO} ap61.rom
Using default protocol (TFTP)
Raw file loaded 0×80040800-0×80068f17, assumed entry at 0×80040800

Original Post:
DD-WRT> load -r -b %{FREEMEMLO} ap61.rom
Using default protocol (TFTP)
Raw file loaded 0×80080000-0×800a8717, assumed entry at 0×80080000

My router:
DD-WRT> fis create -l 0×30000 -e 0xbfc00000 RedBoot
An image named ‘RedBoot’ exists – continue (y/n)? y
… Erase from 0xbfc00000-0xbfc30000: …
… Program from 0×80040800-0×80068f18 at 0xbfc00000: …
… Erase from 0xbffe0000-0xbfff0000: .
… Program from 0×80ff0000-0×81000000 at 0xbffe0000: .

Original post:
DD-WRT> fis create -l 0×30000 -e 0xbfc00000 RedBoot
An image named ‘RedBoot’ exists – continue (y/n)? y
… Erase from 0xbfc00000-0xbfc30000: …
… Program from 0×80080000-0×800a8718 at 0xbfc00000: …
… Erase from 0xbffe0000-0xbfff0000: .
… Program from 0×807f0000-0×80800000 at 0xbffe0000: .
DD-WRT> reset


What do you think about?

Thanks in advance!