where is there, LANTIS ?
post a picture plz
TKS
WDS in 1 network? possible??
Moderator: Moderators
Re: WDS in 1 network? possible??
http://imgur.com/WdsWYee
Set the Bridge IP to a different subnet to the network you want to repeat.
Set the Gateway/AP ip to the IP address of the gateway in the network you want to repeat.
Set the subnet mask to the same as the AP subnet mask.
Please be aware that the relay can take a minute to connect.
Set the Bridge IP to a different subnet to the network you want to repeat.
Set the Gateway/AP ip to the IP address of the gateway in the network you want to repeat.
Set the subnet mask to the same as the AP subnet mask.
Please be aware that the relay can take a minute to connect.
https://lantisproject.com/downloads/gargoylebuilds for the latest releases
Please be respectful when posting. I do this in my free time on a volunteer basis.
Please be respectful when posting. I do this in my free time on a volunteer basis.
Re: WDS in 1 network? possible??
Can u post a capture of screen to show where are the buttons ?
many thanks
many thanks
Re: WDS in 1 network? possible??
What buttons?
This section is immediately below where you choose between Gateway or Bridge
This section is immediately below where you choose between Gateway or Bridge
https://lantisproject.com/downloads/gargoylebuilds for the latest releases
Please be respectful when posting. I do this in my free time on a volunteer basis.
Please be respectful when posting. I do this in my free time on a volunteer basis.
Re: WDS in 1 network? possible??
https://www.youtube.com/watch?v=-Vi91fTqsEULantis wrote:Just update to the latest version I put it all in there. You can then just click some buttons and set it up.
Make sure when you set the router IP it is outside the subnet of the host.
any more simpler method(like NAT) to view my colleugue's share folder
http://wiki.mikrotik.com/wiki/NAT_Tutorial
when C2 cmp under 2 router which is connect to wan port ( 192.168.0.X can read 192.168.5.X) ?
Re: WDS in 1 network? possible??
It will (should) work fine because all of the devices end up on the same subnet.
https://lantisproject.com/downloads/gargoylebuilds for the latest releases
Please be respectful when posting. I do this in my free time on a volunteer basis.
Please be respectful when posting. I do this in my free time on a volunteer basis.
Re: WDS in 1 network? possible??
In the first post there is a picture: 841N & 741ND:Lantis wrote:http://imgur.com/WdsWYee
Set the Bridge IP to a different subnet to the network you want to repeat.
Set the Gateway/AP ip to the IP address of the gateway in the network you want to repeat.
Set the subnet mask to the same as the AP subnet mask.
Please be aware that the relay can take a minute to connect.
741ND is Bridge, 841N is Gateway/AP , right?
Do I need to flash 841N & 741ND to openwrt?
or just need to flash to be gargoyle ?
( my aim is let all device in one same network , so all device can get IP automatically and see each other
Thanks
Re: WDS in 1 network? possible??
its seems that I only need to flash WR741ND to be gargoyle !ispyisail wrote:https://www.gargoyle-router.com/wiki/do ... e_repeater
Re: WDS in 1 network? possible??
I want to ask :chiwing wrote:its seems that I only need to flash WR741ND to be gargoyle !ispyisail wrote:https://www.gargoyle-router.com/wiki/do ... e_repeater
relayD , does it have delay ?
Do i only need to flash gargoyle to WR741ND, then the last IP camera that receive signal from wr741ND can get IP address 10.10.179.X ?
THANKS