DIR-300-Sucess IN DD-WRT But not gargoyle

Report problems and success stories with Gargoyle on various hardware platforms.

Moderator: Moderators

Post Reply
shaunpurpleman
Posts: 1
Joined: Tue Feb 09, 2010 9:21 am

DIR-300-Sucess IN DD-WRT But not gargoyle

Post by shaunpurpleman »

Hi Guys/gals,

Went out today mainly because i Finally found a solution to my problems. Bandwidth QUOTA's. And brought the Dlink DIR-300 A1G

HW: A1 - f/w: v1.01-tomi-1.0
S/N: P1RK184xxxxxx

And prepared to install Gargoyle. YAY. Well i was following the guide Linked http://www.gargoyle-router.com/wiki/dok ... nk_dir-300. But also reading Robins Entry's. Everything seem to be going smooth(except when Tftp'ing ap16.ram i had a lot of timeouts. Until i tried typing

load ap61.ram

then pressed <enter>. And straight away type

go <enter>.
(Didin't wait for transfer that is from pumpkin)

So i followed the instructions but got carried away it seems and installed DD-WRT not just the bootloader.

Ok so now i have a DIR-300 with DD-WRT on it working fine. But i Need to know how to get FON Flash to pick up.

it starts trying and then gets to the IP Found and MAC found but then just nothing waited for along time.

Now I can still get into redboot but it displays the wrong prompt DD-WRT>

Is there away i could Fis init and start the tutorial over agian. Any help would be great.

Eric
Site Admin
Posts: 1443
Joined: Sat Jun 14, 2008 1:14 pm

Re: DIR-300-Sucess IN DD-WRT But not gargoyle

Post by Eric »

1) You don't have to go back to the beginning of the tutorial -- once you're at that point you can do multiple tries with FonFlash without any problems (it automatically runs a fis init once it connects)

2) Make sure your're using the version of FonFlash appropriate for Dir300 devices (which right now is windows only unless you compiled from source, because I've been really, really lazy about updating this).

ispyisail
Moderator
Posts: 5194
Joined: Mon Apr 06, 2009 3:15 am
Location: New Zealand

Re: DIR-300-Sucess IN DD-WRT But not gargoyle

Post by ispyisail »

It appears that DD-WRT have changed the redboot files

Are you using old files from here?
http://robin-files.wik.is/Dlink_DIR-300

johni
Posts: 3
Joined: Tue Feb 17, 2009 3:01 pm

Re: DIR-300-Sucess IN DD-WRT But not gargoyle

Post by johni »

I needed a wireless repeater for my sons house.

I have a modified WBR-1310 (modded to 4 MB flash/16MB ram).
It comes up as a DIR-300.

Gargoyle very easy to set up as a repeater (I'm using it now).
I found the DD-WRT software unstable but the OPENWRT seems solid.
The Gargotyle GUI made setup a snap.
I followed this setup.
http://oldwiki.openwrt.org/OpenWrtDocs( ... d)300.html

I did some speed tests and they are fine.

I took some set up pictures if anyone wants some hints.

Johni

ngg.online
Posts: 15
Joined: Sun Nov 08, 2009 6:51 am

Re: DIR-300-Sucess IN DD-WRT But not gargoyle

Post by ngg.online »

see my post Problem + Solution when Flashing D-Link DIR-300 in the Troubleshooting / Report Bugs Section http://www.gargoyle-router.com/phpbb/vi ... &sk=t&sd=a

@Eric could you pleace move my two posts Problem + Solution when Flashing D-Link DIR-300 and Problems + Solution when Flashing La Fonera FON2100 form the Troubleshooting / Report Bugs to this one. 10x
La Fonera Fon 2100 @ 200MHz + Gargoyle 1.2.5
D-Link Dir-300 @ 200MHz + Gargoyle 1.2.3
Buffalo WHR-HP-G54 + Tomato 1.28

ispyisail
Moderator
Posts: 5194
Joined: Mon Apr 06, 2009 3:15 am
Location: New Zealand

Re: DIR-300-Sucess IN DD-WRT But not gargoyle

Post by ispyisail »

@ngg.online

Why don't you make a wiki entry then make forum links to the wiki?

ngg.online
Posts: 15
Joined: Sun Nov 08, 2009 6:51 am

Re: DIR-300-Sucess IN DD-WRT But not gargoyle

Post by ngg.online »

ispyisail wrote:@ngg.online

Why don't you make a wiki entry then make forum links to the wiki?
I believe that I don't have the rights to edit the wiki. Correct me if I am wrong.
La Fonera Fon 2100 @ 200MHz + Gargoyle 1.2.5
D-Link Dir-300 @ 200MHz + Gargoyle 1.2.3
Buffalo WHR-HP-G54 + Tomato 1.28

Post Reply