wr941nd v3.6 wr1043nd v1.8
Moderator: Moderators
-
- Posts: 48
- Joined: Tue Oct 02, 2012 5:27 pm
wr941nd v3.6 wr1043nd v1.8
Hello, I want to install gargoyle in my two router:
WR1043ND v1.8 and v3.6 WR941ND.
I see that exists a file for WR1043ND to revert in case you need to "factory firmware", but can not find for the WR941ND v 3.6. Exist?? Where I can find it?
It can be done via the web interface?
In WR1043ND: when installing gargoyle, I can use 3G modem?
Finally, from your experience, that I should install versions?
WR1043ND v1.8 and v3.6 WR941ND.
I see that exists a file for WR1043ND to revert in case you need to "factory firmware", but can not find for the WR941ND v 3.6. Exist?? Where I can find it?
It can be done via the web interface?
In WR1043ND: when installing gargoyle, I can use 3G modem?
Finally, from your experience, that I should install versions?
Re: wr941nd v3.6 wr1043nd v1.8
first check with openwrt
-
- Posts: 48
- Joined: Tue Oct 02, 2012 5:27 pm
Re: wr941nd v3.6 wr1043nd v1.8
ispyisail wrote:first check with openwrt
Revert to original firmware
You can download the original firmware from the TP-LINK support section and flash it without modification.
Only perform the dd action below if your original firmware has the word "boot" in it, for example, "wr941nv4_en_3_9_17_up_boot(091118).bin". DO NOT dd your original firmware if it has no "boot" in its name, for example, "wr941nv4_en_3_11_5_up(100427).bin", because if you do, you will brick your router ! This was confirmed by supertom64 in wr1043nd.
http://wiki.openwrt.org/toh/tp-link/tl- ... l.firmware
Is this also true in gargoyle?
What about the other questions?
-
- Posts: 48
- Joined: Tue Oct 02, 2012 5:27 pm
Re: wr941nd v3.6 wr1043nd v1.8
ispyisail wrote:first check with openwrt
Is this also true in gargoyle?
What about the other questions?
Best Regards!
Re: wr941nd v3.6 wr1043nd v1.8
some 3G dongles workIn WR1043ND: when installing gargoyle, I can use 3G modem?
works for me with my WR1043nd
none are perfectFinally, from your experience, that I should install versions?
don't knowWR941ND v 3.6. Exist?? Where I can find it?
Re: wr941nd v3.6 wr1043nd v1.8
I have TL-WR941ND v.3.6, use Firefox 15.1.1 for flashing.
First flash with wr941nv3_en_3_13_9_up(120201).bin, then with gargoyle_1.5.4-ar71xx-tl-wr941nd-v3-squashfs-factory.bin and back to stock firmware with wr941nv3_en_3_13_9_up(120201).bin.
The last version of Gargoyle 1.5.7 is not good(weak WiFi, missing channels), better is older.
The access ip adress of Gargoyle is 192.168.1.1, from the last stock is 192.168.0.1
First flash with wr941nv3_en_3_13_9_up(120201).bin, then with gargoyle_1.5.4-ar71xx-tl-wr941nd-v3-squashfs-factory.bin and back to stock firmware with wr941nv3_en_3_13_9_up(120201).bin.
The last version of Gargoyle 1.5.7 is not good(weak WiFi, missing channels), better is older.
The access ip adress of Gargoyle is 192.168.1.1, from the last stock is 192.168.0.1
-
- Posts: 48
- Joined: Tue Oct 02, 2012 5:27 pm
Re: wr941nd v3.6 wr1043nd v1.8
Thanks for your information.slan wrote:I have TL-WR941ND v.3.6, use Firefox 15.1.1 for flashing.
First flash with wr941nv3_en_3_13_9_up(120201).bin, then with gargoyle_1.5.4-ar71xx-tl-wr941nd-v3-squashfs-factory.bin and back to stock firmware with wr941nv3_en_3_13_9_up(120201).bin.
The last version of Gargoyle 1.5.7 is not good(weak WiFi, missing channels), better is older.
The access ip adress of Gargoyle is 192.168.1.1, from the last stock is 192.168.0.1
From your point of view what is the best version for this router?
Re: wr941nd v3.6 wr1043nd v1.8
I use as you the same configuration: TL-WR1043ND(ip:192.168.2.1) is the first router with Gargoyle 1.5.4 and TL-WR941ND(ip:192.168.1.1) as Gateway(Access Point+Client) is second Router. The antennas must be in the right position. Distance between both router is 15 meter and 4 walls. For me is channel 13 20Mhz Channel Width the best, i use wifi analyzer for android on my cellphone to see all networks about me.
With the stock firmware of both routers i have trouble with speed. With Gargoyle i am satisfied.
With the stock firmware of both routers i have trouble with speed. With Gargoyle i am satisfied.
-
- Posts: 48
- Joined: Tue Oct 02, 2012 5:27 pm
Re: wr941nd v3.6 wr1043nd v1.8
I installed it on my WR941ND v3.6 gargoyle 1.47 (stable).
3 days and works perfectly
As reviewed, only the web interface is a bit slow when saving certain changes.
Anyone know when the next stable release comes out?
3 days and works perfectly
As reviewed, only the web interface is a bit slow when saving certain changes.
Anyone know when the next stable release comes out?