You are aware that dmesg is a kernel message log buffer? Every time the router is rebooted, the contents of dmesg are cleared. What you posted probably has nothing to do with your actual problem.
I've run Gargoyle 1.4.x series with near 2 months of uptime without a single reboot between previous releases. You've now had two problem in a couple days...
WRT54GL v1.1 crash
Moderator: Moderators
Re: WRT54GL v1.1 crash
WRT54GL v1.1
Gargoyle 1.4.7
Gargoyle 1.4.7
Re: WRT54GL v1.1 crash
You can try a downgrade but there does not seem to much changed in previous versions of this file. Last change over a year ago.
Does not seem to be a memory problem but rather that your router's either net switch is not responding properly to configuration.
I leaning towards a hardware problem on your end. Could it be getting insufficient air flow to keep it cool? Also there may be a solder joint going bad on you in there.
How old is it and how long does it usually run before you have this issue?
Does not seem to be a memory problem but rather that your router's either net switch is not responding properly to configuration.
I leaning towards a hardware problem on your end. Could it be getting insufficient air flow to keep it cool? Also there may be a solder joint going bad on you in there.
How old is it and how long does it usually run before you have this issue?
Linksys WRT1900ACv2
Netgear WNDR3700v2
TP Link 1043ND v3
TP-Link TL-WDR3600 v1
Buffalo WZR-HP-G300NH2
WRT54G-TM
Netgear WNDR3700v2
TP Link 1043ND v3
TP-Link TL-WDR3600 v1
Buffalo WZR-HP-G300NH2
WRT54G-TM
Re: WRT54GL v1.1 crash
The router would be about 3 months old. It had been working perfectly for about 2 months, now it is crashing on a regular interval.pbix wrote:You can try a downgrade but there does not seem to much changed in previous versions of this file. Last change over a year ago.
Does not seem to be a memory problem but rather that your router's either net switch is not responding properly to configuration.
I leaning towards a hardware problem on your end. Could it be getting insufficient air flow to keep it cool? Also there may be a solder joint going bad on you in there.
How old is it and how long does it usually run before you have this issue?
It is sitting on a table next to adsl modem, clear airflow, and it is cool in the room.
Re: WRT54GL v1.1 crash
Post the contents of dmesg here again now that the router is seemingly working correctly.
WRT54GL v1.1
Gargoyle 1.4.7
Gargoyle 1.4.7
Re: WRT54GL v1.1 crash
I can do that tonight, after I reset up the router again.mix wrote:Post the contents of dmesg here again now that the router is seemingly working correctly.
I will have to do the fisrtboot to clear everything, because it is unusable at the moment.
Re: WRT54GL v1.1 crash
login as: root
root@172.20.14.254's password:
BusyBox v1.15.3 (2012-02-29 19:18:51 EST) built-in shell (ash)
Enter 'help' for a list of built-in commands.
---------------------------------------------------------------
| _____ _ |
| | __ \ | | |
| | | \/ __ _ _ __ __ _ ___ _ _| | ___ |
| | | __ / _` | '__/ _` |/ _ \| | | | |/ _ \ |
| | |_\ \ (_| | | | (_| | (_) | |_| | | __/ |
| \____/\__,_|_| \__, |\___/ \__, |_|\___| |
| __/ | __/ | |
| |___/ |___/ |
| |
|-------------------------------------------------------------|
| Gargoyle version 1.4.7 | OpenWrt backfire branch |
| Gargoyle revision 5783343 | OpenWrt revision r30752 |
| Built February 29, 2012 | Target brcm47xx/default |
---------------------------------------------------------------
root@Gargoyle:~# dmesg
Linux version 2.6.32.27 (eric@Osiris) (gcc version 4.3.3 (GCC) ) #1 Wed Feb 29 19:26:17 EST 2012
CPU revision is: 00029008 (Broadcom BCM3302)
ssb: Core 0 found: ChipCommon (cc 0x800, rev 0x0E, vendor 0x4243)
ssb: Core 1 found: Fast Ethernet (cc 0x806, rev 0x09, vendor 0x4243)
ssb: Core 2 found: MIPS 3302 (cc 0x816, rev 0x06, vendor 0x4243)
ssb: Core 3 found: USB 1.1 Host (cc 0x817, rev 0x02, vendor 0x4243)
ssb: Core 4 found: MEMC SDRAM (cc 0x80F, rev 0x01, vendor 0x4243)
ssb: Core 5 found: IEEE 802.11 (cc 0x812, rev 0x09, vendor 0x4243)
ssb: Core 6 found: Roboswitch (cc 0x81C, rev 0x02, vendor 0x4243)
ssb: chipcommon status is 0x0
ssb: Initializing MIPS core...
ssb: set_irq: core 0x0806, irq 4 => 4
ssb: set_irq: core 0x0816, irq 5 => 2
ssb: set_irq: core 0x0812, irq 2 => 5
ssb: after irq reconfiguration
ssb: core 0x0800, irq : 2(S) 3* 4 5 6 D I
ssb: core 0x0806, irq : 2(S) 3 4* 5 6 D I
ssb: core 0x0816, irq : 2(S)* 3 4 5 6 D I
ssb: core 0x0817, irq : 2(S) 3 4 5 6* D I
ssb: core 0x080f, irq : 2(S) 3 4 5 6 D I*
ssb: core 0x0812, irq : 2(S) 3 4 5* 6 D I
ssb: core 0x081c, irq : 2(S) 3 4 5 6 D I*
ssb: Sonics Silicon Backplane found at address 0x18000000
Serial init done.
Determined physical RAM map:
memory: 01000000 @ 00000000 (usable)
Initrd not found or empty - disabling initrd
Zone PFN ranges:
Normal 0x00000000 -> 0x00001000
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
0: 0x00000000 -> 0x00001000
On node 0 totalpages: 4096
free_area_init_node: node 0, pgdat 8028e0b0, node_mem_map 802d3000
Normal zone: 32 pages used for memmap
Normal zone: 0 pages reserved
Normal zone: 4064 pages, LIFO batch:0
Built 1 zonelists in Zone order, mobility grouping off. Total pages: 4064
Kernel command line: root=/dev/mtdblock2 rootfstype=squashfs,jffs2 noinitrd console=ttyS0,115200
PID hash table entries: 64 (order: -4, 256 bytes)
Dentry cache hash table entries: 2048 (order: 1, 8192 bytes)
Inode-cache hash table entries: 1024 (order: 0, 4096 bytes)
Primary instruction cache 16kB, VIPT, 2-way, linesize 16 bytes.
Primary data cache 8kB, 2-way, VIPT, no aliases, linesize 16 bytes
Memory: 13332k/16384k available (2264k kernel code, 3052k reserved, 349k data, 136k init, 0k highmem)
Hierarchical RCU implementation.
NR_IRQS:128
console [ttyS0] enabled
Calibrating delay loop... 199.16 BogoMIPS (lpj=398336)
Mount-cache hash table entries: 512
NET: Registered protocol family 16
bio: create slab <bio-0> at 0
Switching to clocksource MIPS
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 512 (order: 0, 4096 bytes)
TCP bind hash table entries: 512 (order: -1, 2048 bytes)
TCP: Hash tables configured (established 512 bind 512)
TCP reno registered
NET: Registered protocol family 1
squashfs: version 4.0 (2009/01/31) Phillip Lougher
Registering mini_fo version $Id$
JFFS2 version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc.
msgmni has been set to 26
io scheduler noop registered
io scheduler deadline registered (default)
Serial: 8250/16550 driver, 2 ports, IRQ sharing enabled
serial8250: ttyS0 at MMIO 0xb8000300 (irq = 3) is a 16550A
serial8250: ttyS1 at MMIO 0xb8000400 (irq = 3) is a 16550A
serial8250.0: ttyS0 at MMIO 0xb8000300 (irq = 3) is a 16550A
serial8250.0: ttyS1 at MMIO 0xb8000400 (irq = 3) is a 16550A
flash init: 0x1c000000 0x02000000
Physically mapped flash: Found 1 x16 devices at 0x0 in 16-bit bank
Physically mapped flash: Found an alias at 0x400000 for the chip at 0x0
Physically mapped flash: Found an alias at 0x800000 for the chip at 0x0
Physically mapped flash: Found an alias at 0xc00000 for the chip at 0x0
Physically mapped flash: Found an alias at 0x1000000 for the chip at 0x0
Physically mapped flash: Found an alias at 0x1400000 for the chip at 0x0
Physically mapped flash: Found an alias at 0x1800000 for the chip at 0x0
Physically mapped flash: Found an alias at 0x1c00000 for the chip at 0x0
CFI mfr 0x000000c2
CFI id 0x000022a8
Amd/Fujitsu Extended Query Table at 0x0040
Amd/Fujitsu Extended Query version 1.1.
number of CFI chips: 1
cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
Flash device: 0x400000 at 0x1fc00000
bootloader size: 262144
Creating 4 MTD partitions on "Physically mapped flash":
0x000000000000-0x000000040000 : "cfe"
0x000000040000-0x0000003f0000 : "linux"
0x000000115800-0x0000003f0000 : "rootfs"
mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
mtd: partition "rootfs" set to be root filesystem
mtd: partition "rootfs_data" created automatically, ofs=340000, len=B0000
0x000000340000-0x0000003f0000 : "rootfs_data"
0x0000003f0000-0x000000400000 : "nvram"
b44.c:v2.0
eth0: Broadcom 44xx/47xx 10/100BaseT Ethernet 58:6d:8f:c7:c8:3b
BCM47xx Watchdog Timer enabled (30 seconds, nowayout)
TCP westwood registered
NET: Registered protocol family 17
Bridge firewalling registered
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
Freeing unused kernel memory: 136k freed
Please be patient, while OpenWrt loads ...
diag: Detected 'Linksys WRT54G/GS/GL'
b44: eth0: Link is up at 100 Mbps, full duplex.
b44: eth0: Flow control is off for TX and off for RX.
roboswitch: Probing device eth0: found a 5325! It's a 5350.
mini_fo: using base directory: /
mini_fo: using storage directory: /overlay
b44: eth0: powering down PHY
b44: eth0: Link is up at 100 Mbps, full duplex.
b44: eth0: Flow control is off for TX and off for RX.
device eth0.0 entered promiscuous mode
device eth0 entered promiscuous mode
br-lan: port 1(eth0.0) entering forwarding state
Compat-wireless backport release: compat-wireless-2011-11-29
Backport based on wireless-testing.git master-2011-12-01
cfg80211: Calling CRDA to update world regulatory domain
b43-phy0: Broadcom 5352 WLAN found (core revision 9)
ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
Registered led device: b43-phy0::tx
Registered led device: b43-phy0::rx
Registered led device: b43-phy0::radio
Broadcom 43xx driver loaded [ Features: PL ]
Broadcom 43xx-legacy driver loaded [ Features: PLID ]
cfg80211: World regulatory domain updated:
cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
PPP generic driver version 2.4.2
ip_tables: (C) 2000-2006 Netfilter Core Team
NET: Registered protocol family 24
nf_conntrack version 0.5.0 (210 buckets, 840 max)
CONFIG_NF_CT_ACCT is deprecated and will be removed soon. Please use
nf_conntrack.acct=1 kernel parameter, acct=1 nf_conntrack module option or
sysctl net.netfilter.nf_conntrack_acct=1 to enable it.
xt_time: kernel timezone is -0000
Hooked IMQ after mangle on PREROUTING
Hooked IMQ after nat on POSTROUTING
IMQ driver loaded successfully.
Ebtables v2.0 registered
b43-phy0: Loading firmware version 410.2160 (2007-05-26 15:32:10)
b43-phy0: Loading firmware version 410.2160 (2007-05-26 15:32:10)
device wlan0 entered promiscuous mode
br-lan: port 2(wlan0) entering forwarding state
device wlan0 left promiscuous mode
br-lan: port 2(wlan0) entering disabled state
device wlan0 entered promiscuous mode
br-lan: port 2(wlan0) entering forwarding state
ipt_bandwidth: timezone shift of 600 minutes detected, adjusting
old minutes west=0, new minutes west=-600
IMQ driver unloaded successfully.
Hooked IMQ after mangle on INPUT
Hooked IMQ after mangle on FORWARD
IMQ driver loaded successfully.
root@Gargoyle:~# df -h
Filesystem Size Used Available Use% Mounted on
/dev/root 2.3M 2.3M 0 100% /rom
tmpfs 6.6M 68.0K 6.5M 1% /tmp
tmpfs 512.0K 0 512.0K 0% /dev
/dev/mtdblock3 704.0K 232.0K 472.0K 33% /overlay
mini_fo:/overlay 2.3M 2.3M 0 100% /
root@Gargoyle:~#
root@172.20.14.254's password:
BusyBox v1.15.3 (2012-02-29 19:18:51 EST) built-in shell (ash)
Enter 'help' for a list of built-in commands.
---------------------------------------------------------------
| _____ _ |
| | __ \ | | |
| | | \/ __ _ _ __ __ _ ___ _ _| | ___ |
| | | __ / _` | '__/ _` |/ _ \| | | | |/ _ \ |
| | |_\ \ (_| | | | (_| | (_) | |_| | | __/ |
| \____/\__,_|_| \__, |\___/ \__, |_|\___| |
| __/ | __/ | |
| |___/ |___/ |
| |
|-------------------------------------------------------------|
| Gargoyle version 1.4.7 | OpenWrt backfire branch |
| Gargoyle revision 5783343 | OpenWrt revision r30752 |
| Built February 29, 2012 | Target brcm47xx/default |
---------------------------------------------------------------
root@Gargoyle:~# dmesg
Linux version 2.6.32.27 (eric@Osiris) (gcc version 4.3.3 (GCC) ) #1 Wed Feb 29 19:26:17 EST 2012
CPU revision is: 00029008 (Broadcom BCM3302)
ssb: Core 0 found: ChipCommon (cc 0x800, rev 0x0E, vendor 0x4243)
ssb: Core 1 found: Fast Ethernet (cc 0x806, rev 0x09, vendor 0x4243)
ssb: Core 2 found: MIPS 3302 (cc 0x816, rev 0x06, vendor 0x4243)
ssb: Core 3 found: USB 1.1 Host (cc 0x817, rev 0x02, vendor 0x4243)
ssb: Core 4 found: MEMC SDRAM (cc 0x80F, rev 0x01, vendor 0x4243)
ssb: Core 5 found: IEEE 802.11 (cc 0x812, rev 0x09, vendor 0x4243)
ssb: Core 6 found: Roboswitch (cc 0x81C, rev 0x02, vendor 0x4243)
ssb: chipcommon status is 0x0
ssb: Initializing MIPS core...
ssb: set_irq: core 0x0806, irq 4 => 4
ssb: set_irq: core 0x0816, irq 5 => 2
ssb: set_irq: core 0x0812, irq 2 => 5
ssb: after irq reconfiguration
ssb: core 0x0800, irq : 2(S) 3* 4 5 6 D I
ssb: core 0x0806, irq : 2(S) 3 4* 5 6 D I
ssb: core 0x0816, irq : 2(S)* 3 4 5 6 D I
ssb: core 0x0817, irq : 2(S) 3 4 5 6* D I
ssb: core 0x080f, irq : 2(S) 3 4 5 6 D I*
ssb: core 0x0812, irq : 2(S) 3 4 5* 6 D I
ssb: core 0x081c, irq : 2(S) 3 4 5 6 D I*
ssb: Sonics Silicon Backplane found at address 0x18000000
Serial init done.
Determined physical RAM map:
memory: 01000000 @ 00000000 (usable)
Initrd not found or empty - disabling initrd
Zone PFN ranges:
Normal 0x00000000 -> 0x00001000
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
0: 0x00000000 -> 0x00001000
On node 0 totalpages: 4096
free_area_init_node: node 0, pgdat 8028e0b0, node_mem_map 802d3000
Normal zone: 32 pages used for memmap
Normal zone: 0 pages reserved
Normal zone: 4064 pages, LIFO batch:0
Built 1 zonelists in Zone order, mobility grouping off. Total pages: 4064
Kernel command line: root=/dev/mtdblock2 rootfstype=squashfs,jffs2 noinitrd console=ttyS0,115200
PID hash table entries: 64 (order: -4, 256 bytes)
Dentry cache hash table entries: 2048 (order: 1, 8192 bytes)
Inode-cache hash table entries: 1024 (order: 0, 4096 bytes)
Primary instruction cache 16kB, VIPT, 2-way, linesize 16 bytes.
Primary data cache 8kB, 2-way, VIPT, no aliases, linesize 16 bytes
Memory: 13332k/16384k available (2264k kernel code, 3052k reserved, 349k data, 136k init, 0k highmem)
Hierarchical RCU implementation.
NR_IRQS:128
console [ttyS0] enabled
Calibrating delay loop... 199.16 BogoMIPS (lpj=398336)
Mount-cache hash table entries: 512
NET: Registered protocol family 16
bio: create slab <bio-0> at 0
Switching to clocksource MIPS
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 512 (order: 0, 4096 bytes)
TCP bind hash table entries: 512 (order: -1, 2048 bytes)
TCP: Hash tables configured (established 512 bind 512)
TCP reno registered
NET: Registered protocol family 1
squashfs: version 4.0 (2009/01/31) Phillip Lougher
Registering mini_fo version $Id$
JFFS2 version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc.
msgmni has been set to 26
io scheduler noop registered
io scheduler deadline registered (default)
Serial: 8250/16550 driver, 2 ports, IRQ sharing enabled
serial8250: ttyS0 at MMIO 0xb8000300 (irq = 3) is a 16550A
serial8250: ttyS1 at MMIO 0xb8000400 (irq = 3) is a 16550A
serial8250.0: ttyS0 at MMIO 0xb8000300 (irq = 3) is a 16550A
serial8250.0: ttyS1 at MMIO 0xb8000400 (irq = 3) is a 16550A
flash init: 0x1c000000 0x02000000
Physically mapped flash: Found 1 x16 devices at 0x0 in 16-bit bank
Physically mapped flash: Found an alias at 0x400000 for the chip at 0x0
Physically mapped flash: Found an alias at 0x800000 for the chip at 0x0
Physically mapped flash: Found an alias at 0xc00000 for the chip at 0x0
Physically mapped flash: Found an alias at 0x1000000 for the chip at 0x0
Physically mapped flash: Found an alias at 0x1400000 for the chip at 0x0
Physically mapped flash: Found an alias at 0x1800000 for the chip at 0x0
Physically mapped flash: Found an alias at 0x1c00000 for the chip at 0x0
CFI mfr 0x000000c2
CFI id 0x000022a8
Amd/Fujitsu Extended Query Table at 0x0040
Amd/Fujitsu Extended Query version 1.1.
number of CFI chips: 1
cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
Flash device: 0x400000 at 0x1fc00000
bootloader size: 262144
Creating 4 MTD partitions on "Physically mapped flash":
0x000000000000-0x000000040000 : "cfe"
0x000000040000-0x0000003f0000 : "linux"
0x000000115800-0x0000003f0000 : "rootfs"
mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
mtd: partition "rootfs" set to be root filesystem
mtd: partition "rootfs_data" created automatically, ofs=340000, len=B0000
0x000000340000-0x0000003f0000 : "rootfs_data"
0x0000003f0000-0x000000400000 : "nvram"
b44.c:v2.0
eth0: Broadcom 44xx/47xx 10/100BaseT Ethernet 58:6d:8f:c7:c8:3b
BCM47xx Watchdog Timer enabled (30 seconds, nowayout)
TCP westwood registered
NET: Registered protocol family 17
Bridge firewalling registered
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
Freeing unused kernel memory: 136k freed
Please be patient, while OpenWrt loads ...
diag: Detected 'Linksys WRT54G/GS/GL'
b44: eth0: Link is up at 100 Mbps, full duplex.
b44: eth0: Flow control is off for TX and off for RX.
roboswitch: Probing device eth0: found a 5325! It's a 5350.
mini_fo: using base directory: /
mini_fo: using storage directory: /overlay
b44: eth0: powering down PHY
b44: eth0: Link is up at 100 Mbps, full duplex.
b44: eth0: Flow control is off for TX and off for RX.
device eth0.0 entered promiscuous mode
device eth0 entered promiscuous mode
br-lan: port 1(eth0.0) entering forwarding state
Compat-wireless backport release: compat-wireless-2011-11-29
Backport based on wireless-testing.git master-2011-12-01
cfg80211: Calling CRDA to update world regulatory domain
b43-phy0: Broadcom 5352 WLAN found (core revision 9)
ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
Registered led device: b43-phy0::tx
Registered led device: b43-phy0::rx
Registered led device: b43-phy0::radio
Broadcom 43xx driver loaded [ Features: PL ]
Broadcom 43xx-legacy driver loaded [ Features: PLID ]
cfg80211: World regulatory domain updated:
cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
PPP generic driver version 2.4.2
ip_tables: (C) 2000-2006 Netfilter Core Team
NET: Registered protocol family 24
nf_conntrack version 0.5.0 (210 buckets, 840 max)
CONFIG_NF_CT_ACCT is deprecated and will be removed soon. Please use
nf_conntrack.acct=1 kernel parameter, acct=1 nf_conntrack module option or
sysctl net.netfilter.nf_conntrack_acct=1 to enable it.
xt_time: kernel timezone is -0000
Hooked IMQ after mangle on PREROUTING
Hooked IMQ after nat on POSTROUTING
IMQ driver loaded successfully.
Ebtables v2.0 registered
b43-phy0: Loading firmware version 410.2160 (2007-05-26 15:32:10)
b43-phy0: Loading firmware version 410.2160 (2007-05-26 15:32:10)
device wlan0 entered promiscuous mode
br-lan: port 2(wlan0) entering forwarding state
device wlan0 left promiscuous mode
br-lan: port 2(wlan0) entering disabled state
device wlan0 entered promiscuous mode
br-lan: port 2(wlan0) entering forwarding state
ipt_bandwidth: timezone shift of 600 minutes detected, adjusting
old minutes west=0, new minutes west=-600
IMQ driver unloaded successfully.
Hooked IMQ after mangle on INPUT
Hooked IMQ after mangle on FORWARD
IMQ driver loaded successfully.
root@Gargoyle:~# df -h
Filesystem Size Used Available Use% Mounted on
/dev/root 2.3M 2.3M 0 100% /rom
tmpfs 6.6M 68.0K 6.5M 1% /tmp
tmpfs 512.0K 0 512.0K 0% /dev
/dev/mtdblock3 704.0K 232.0K 472.0K 33% /overlay
mini_fo:/overlay 2.3M 2.3M 0 100% /
root@Gargoyle:~#
Re: WRT54GL v1.1 crash
I recommend you take your two dmesg files over to openwrt.org and post there. You might get someone there who knows something about this. You can see that there is a problem in the hardware initialization so it is a pretty low level openwrt thing in my view.
Linksys WRT1900ACv2
Netgear WNDR3700v2
TP Link 1043ND v3
TP-Link TL-WDR3600 v1
Buffalo WZR-HP-G300NH2
WRT54G-TM
Netgear WNDR3700v2
TP Link 1043ND v3
TP-Link TL-WDR3600 v1
Buffalo WZR-HP-G300NH2
WRT54G-TM
Re: WRT54GL v1.1 crash
Really, what error am I missing?
What does a good dmesg show?
What does a good dmesg show?
Re: WRT54GL v1.1 crash
The Ethernet switch fails to initialize. You can see it in the first dmesg file
Linksys WRT1900ACv2
Netgear WNDR3700v2
TP Link 1043ND v3
TP-Link TL-WDR3600 v1
Buffalo WZR-HP-G300NH2
WRT54G-TM
Netgear WNDR3700v2
TP Link 1043ND v3
TP-Link TL-WDR3600 v1
Buffalo WZR-HP-G300NH2
WRT54G-TM
Re: WRT54GL v1.1 crash
Wouldn't waste your time posting any of this to openwrt forum, the response if any will be something along the lines of, "WTF is /home/eric/gargoyle_1.4/brcm47xx-src/build_dir/linux-brcm47xx/kmod-switch/switch-robo.c? Code that is compiled with missing sources? Use the official release."
I guess I should boot into failsafe mode and see if dmesg gives me the same error message.
I guess I should boot into failsafe mode and see if dmesg gives me the same error message.
WRT54GL v1.1
Gargoyle 1.4.7
Gargoyle 1.4.7