Differences

This shows you the differences between two versions of the page.

--- supported_routers_-_tested_routers [2016/05/03 00:49]
lceron [Atheros AR71XX Routers:]
+++ supported_routers_-_tested_routers [2019/12/21 18:15] (current)
ispyisail [Marvell Armada XP/370 Routers:]
@@ Line 14: / Line 14: @@
   * **Recommended minimum** 8MB of FLASH and 32MB of RAM to run the latest versions of Gargoyle.
-  * **Bare minimum** 4MB of FLASH and 32MB of RAM __may__ run the latest versions of Gargoyle. 4MB of FLASH is insufficient to support the Gargoyle USB functionality. Also, some users report difficulty saving config settings and/or loading additional packages. If you have an old router then give it a try, but __don't buy a bare minimum router__ for Gargoyle.
+  * **Bare minimum** 4MB of FLASH and 32MB of RAM will NOT run latest versions of Gargoyle (>1.8.x). 4MB of FLASH is insufficient to support the Gargoyle USB functionality. Also, some users report difficulty saving config settings and/or loading additional packages. If you have an old router then give it a try, but __don't buy a bare minimum router__ for Gargoyle.
   * **Sub-minimum** routers with only 16MB of RAM are best matched with Gargoyle 1.2.5, which has a smaller memory footprint.
@@ Line 26: / Line 26: @@
 \\ \\
+====Marvell Armada XP/370 Routers:====
+Routers with this architecture are fully supported for Gargoyle.
+There are typically two files available for each of these routers:
+  *  use **factory.bin** to __install__ Gargoyle over the original manufacturer's firmware
+  *  use **sysupgrade.bin** to __upgrade__ an existing Gargoyle/OpenWrt installation
+=== Linksys ===
+^ Model ^ RAM ^ Flash ^ CPU MHz ^ Firmware File(s) ^
+^ Linksys WRT AC Series |||||
+| WRT1200AC v1 (Caiman) | 512MB | 128NAND | 2x 1300 | *-mvebu-cortexa9-linksys-wrt1200ac-squashfs-* |
+| WRT1200AC v2 (Caiman) | 512MB | 128NAND | 2x 1300 | *-mvebu-cortexa9-linksys-wrt1200ac-squashfs-* |
+| WRT1900AC v1 (Mamba) | 256MB | 128NAND | 2x 1200 | *-mvebu-cortexa9-linksys-wrt1900ac-squashfs-* |
+| WRT1900AC v2 (Cobra) | 512MB | 128NAND | 2x 1600 | *-mvebu-cortexa9-linksys-wrt1900acv2-squashfs-* |
+| WRT1900ACS v1 (Shelby) | 512MB | 128NAND | 2x 1600 | *-mvebu-cortexa9-linksys-wrt1900acs-squashfs-* |
+| WRT1900ACS v2 (Shelby) | 512MB | 128NAND | 2x 1600 | *-mvebu-cortexa9-linksys-wrt1900acs-squashfs-* |
+| WRT3200ACM v1 (Rango) | 512MB | 256NAND | 2x 1866 | *-mvebu-cortexa9-linksys-wrt3200acm-squashfs-* |
+| WRT32X v1 (Venom) | 512MB | 256NAND | 2x 1866 | *-mvebu-cortexa9-linksys-wrt32x-squashfs-* |
+=== Turris Omnia ===
+^ Model ^ RAM ^ Flash ^ CPU MHz ^ Firmware File(s) ^
+^ Turris Omnia |||||
+| Turris Omnia | 1-2 GB | 8 GB Flash | 2 x 1600 | *-mvebu-cortexa9-turris-omnia-* |
 ====Atheros AR71XX Routers:====
-Routers with this architecture are the best-supported routers that run Gargoyle.
+These routers are getting hard to find and flash
 There are typically two files available for each of these routers:
@@ Line 38: / Line 67: @@
 ^ Model ^ RAM ^ Flash ^ USB ^ Firmware File(s) ^
+^ GL.iNet|||||
+|GL.iNet AR150 | 64MB | 16MB | 1 | *-generic-gl_ar150-* |
 ^ TP-Link Routers (([[tp-link-install|install notes]])) |||||
 | TL-Archer C7 v2 (([[http://www.gargoyle-router.com/phpbb/viewtopic.php?f=3&t=7431&start=40#p31132|Gargoyle v8]])) | 128MB | 16MB | 2 | *-generic-archer-c7-v2-* |

Gargoyle Wiki

User Tools

Site Tools

Differences

Page Tools