Differences

This shows you the differences between two versions of the page.

--- supported_routers_-_tested_routers [2015/09/09 20:56]
nworbnhoj [Atheros AR71XX Routers:] Consolidate TL-WR941
+++ supported_routers_-_tested_routers [2019/12/21 18:15] (current)
ispyisail [Marvell Armada XP/370 Routers:]
@@ Line 14: / Line 14: @@
   * **Recommended minimum** 8MB of FLASH and 32MB of RAM to run the latest versions of Gargoyle.
-  * **Bare minimum** 4MB of FLASH and 32MB of RAM __may__ run the latest versions of Gargoyle. 4MB of FLASH is insufficient to support the Gargoyle USB functionality. Also, some users report difficulty saving config settings and/or loading additional packages. If you have an old router then give it a try, but __don't buy a bare minimum router__ for Gargoyle.
+  * **Bare minimum** 4MB of FLASH and 32MB of RAM will NOT run latest versions of Gargoyle (>1.8.x). 4MB of FLASH is insufficient to support the Gargoyle USB functionality. Also, some users report difficulty saving config settings and/or loading additional packages. If you have an old router then give it a try, but __don't buy a bare minimum router__ for Gargoyle.
   * **Sub-minimum** routers with only 16MB of RAM are best matched with Gargoyle 1.2.5, which has a smaller memory footprint.
@@ Line 26: / Line 26: @@
 \\ \\
+====Marvell Armada XP/370 Routers:====
+Routers with this architecture are fully supported for Gargoyle.
+There are typically two files available for each of these routers:
+  *  use **factory.bin** to __install__ Gargoyle over the original manufacturer's firmware
+  *  use **sysupgrade.bin** to __upgrade__ an existing Gargoyle/OpenWrt installation
+=== Linksys ===
+^ Model ^ RAM ^ Flash ^ CPU MHz ^ Firmware File(s) ^
+^ Linksys WRT AC Series |||||
+| WRT1200AC v1 (Caiman) | 512MB | 128NAND | 2x 1300 | *-mvebu-cortexa9-linksys-wrt1200ac-squashfs-* |
+| WRT1200AC v2 (Caiman) | 512MB | 128NAND | 2x 1300 | *-mvebu-cortexa9-linksys-wrt1200ac-squashfs-* |
+| WRT1900AC v1 (Mamba) | 256MB | 128NAND | 2x 1200 | *-mvebu-cortexa9-linksys-wrt1900ac-squashfs-* |
+| WRT1900AC v2 (Cobra) | 512MB | 128NAND | 2x 1600 | *-mvebu-cortexa9-linksys-wrt1900acv2-squashfs-* |
+| WRT1900ACS v1 (Shelby) | 512MB | 128NAND | 2x 1600 | *-mvebu-cortexa9-linksys-wrt1900acs-squashfs-* |
+| WRT1900ACS v2 (Shelby) | 512MB | 128NAND | 2x 1600 | *-mvebu-cortexa9-linksys-wrt1900acs-squashfs-* |
+| WRT3200ACM v1 (Rango) | 512MB | 256NAND | 2x 1866 | *-mvebu-cortexa9-linksys-wrt3200acm-squashfs-* |
+| WRT32X v1 (Venom) | 512MB | 256NAND | 2x 1866 | *-mvebu-cortexa9-linksys-wrt32x-squashfs-* |
+=== Turris Omnia ===
+^ Model ^ RAM ^ Flash ^ CPU MHz ^ Firmware File(s) ^
+^ Turris Omnia |||||
+| Turris Omnia | 1-2 GB | 8 GB Flash | 2 x 1600 | *-mvebu-cortexa9-turris-omnia-* |
 ====Atheros AR71XX Routers:====
-Routers with this architecture are the best-supported routers that run Gargoyle.
+These routers are getting hard to find and flash
 There are typically two files available for each of these routers:
@@ Line 38: / Line 67: @@
 ^ Model ^ RAM ^ Flash ^ USB ^ Firmware File(s) ^
+^ GL.iNet|||||
+|GL.iNet AR150 | 64MB | 16MB | 1 | *-generic-gl_ar150-* |
 ^ TP-Link Routers (([[tp-link-install|install notes]])) |||||
 | TL-Archer C7 v2 (([[http://www.gargoyle-router.com/phpbb/viewtopic.php?f=3&t=7431&start=40#p31132|Gargoyle v8]])) | 128MB | 16MB | 2 | *-generic-archer-c7-v2-* |
@@ Line 46: / Line 77: @@
 | ^  Rec Min  || ||
 | TL-WR1043ND v1.x (([[http://www.gargoyle-router.com/phpbb/viewtopic.php?f=3&t=7431&start=10#p30942|loaded on Gargoyle v1.8]])) | 32MB | 8MB | 1((The TL-WR1043ND v1.x does not deliver enough power for most USB 3G modems. See [[http://wiki.openwrt.org/toh/tp-link/tl-wr1043nd?&#usb_3g_modems|OpenWRT]] for details)) | *-tl-wr1043nd-v1-* |
-| TL-WR841N v1.5 | 32MB | 8MB | No | *-tl-wr841n-v1.5-* |
 | TL-WDR3700 v2 (([[http://www.gargoyle-router.com/phpbb/viewtopic.php?f=3&t=7431&start=50#p31251|Gargoyle v1.8]])) | 16MB | 16MB | 1 | *-tl-wdr3700-v2-* |
 | ^  Bare Min  || ||
 | TL-WR941ND v2 v3(([[http://www.gargoyle-router.com/phpbb/viewtopic.php?f=3&t=7431#p30903|Gargoyle v1.8]])) v4 | 32MB | 4MB | No | *-tl-wr941nd-vx-* |
 | TL-WR841ND v3-9 (([[http://www.gargoyle-router.com/phpbb/viewtopic.php?f=11&t=7521&p=31441#p31441|v8 & Gargoyle v1.8]]))(([[http://www.gargoyle-router.com/phpbb/viewtopic.php?f=8&t=7291&p=31458#p31458|v9 & Gargoyle v1.8]]))  | 32MB | 4MB | No | *-tl-wr841nd-vx-* |
-| TL-WR741ND\\ v1-1.9 & v2 & v2.4 | 32MB | 4MB | No | *-tl-wr741nd-v1-* |
+| TL-WR741ND v1-1.9 | 32MB | 4MB | No | *-tl-wr741nd-v1-* |
+| TL-WR741ND v2 & v2.4 | 32MB | 4MB | No | *-tl-wr741nd-v2-* |
 ^ Buffalo Routers |||||
 | WZR-600DHP | 128MB | 32MB | 1 | *-ag300h-* |
 | WZR-HP-G300NH(([[buffalo_wzr-hp-g300nh|install notes]])) | 64MB | 32MB | 1 | *-wzr-hp-g300nh-* |
 ^ Netgear Routers |||||
-| WNDR3700v2 | 64MB | 16MB | 1 | *-wndr3700-* |
 | WNDR3700v1 | 64MB | 8MB | 1 | *-wndr3700-* |
+| WNDR3700v2 | 64MB | 16MB | 1 | *-wndr37002-* |
+| WNDR3700v4 | 128MB | 128MB | 1 | *-wndr3700v4-* |
+| WNDR3800 | 128MB | 16MB | 1 | *-wndr3800-* |
+| WNDR4300v1 | 128MB | 128MB | 1 | *-wndr4300-* |
+| WNDRMAC | 16MB | 64MB | 1 | *-wndrmac-* |
+| WNDRMACv2 | 16MB | 128MB | 1 | *-wndrmacv2-* |
 ^ D-Link Routers |||||
 | DIR-825 b1,b2| 64MB | 8MB | 1 | *-dir-825-* |

Gargoyle Wiki

User Tools

Site Tools

Differences

Page Tools