Hi all,
Just setting up a router with Gargoyle and having a few problems getting external access to work.
I have had a bit of a search on the net, but not found anything that has helped me so far.
That could be because of my pretty (very) basic understanding of networking stuff.
Basically i have a DG834G modem connecting to the net,
a NDR3700v2 with Gargoyle running
and i want to connect to my NAS and LAPTOP from outside via FTP/VNC/etc
How do i do this?
I have set a static route on the DG834G
and when i forwarded the port of the Gargoyle GUI i was able to connect to it externally
But i am having no luck getting past it.
I have added port forwards on the gargoyle NDR3700v2 to no avail.
I was winging this setup so i suspect i have it configured wrong for my hardware.
Here is the full setup with details i thought important
Any help much appreciated.
-= INTERNET =-
---------------^--------------
Netger DG834G v5
Encapsulation: PPPoE
Internet IP Address: Get Dynamically from ISP
DNS Address: Get Automatically From ISP
NAT: Enabled
LAN IP: 192.168.0.1
DHCP Server: On
Static Routes: 1- Destination: 192.168.1.0 Gateway :192.168.0.3
---------------|-------------
Cable to WAN port
---------------^--------------
NETGEAR NDR3700v2
Gargoyle Version: 1.5.8
Device Configuration: Gateway
Connect Via: DCHP (wired)
LAN IP: 192.168.1.2
DHCP Server: On
---------------|-------------
Several Wired and wireless devices connected
Gargoyle Router - Setup/Access questions
Moderator: Moderators
Re: Gargoyle Router - Setup/Access questions
You would simplify your life by switching your DG834 to bridge mode. It will also give better performance of your WAN link.
I saw this post http://blog.crox.net/archives/40-Netgea ... PPPoE.html on how to do it.
Then use Gargoyle to do your PPPoE. Also read http://www.gargoyle-router.com/wiki/dok ... &s[]=pppoe
I saw this post http://blog.crox.net/archives/40-Netgea ... PPPoE.html on how to do it.
Then use Gargoyle to do your PPPoE. Also read http://www.gargoyle-router.com/wiki/dok ... &s[]=pppoe
Linksys WRT1900ACv2
Netgear WNDR3700v2
TP Link 1043ND v3
TP-Link TL-WDR3600 v1
Buffalo WZR-HP-G300NH2
WRT54G-TM
Netgear WNDR3700v2
TP Link 1043ND v3
TP-Link TL-WDR3600 v1
Buffalo WZR-HP-G300NH2
WRT54G-TM
Re: Gargoyle Router - Setup/Access questions
Thanks for your reply,
i must have browsed over a ton of threads with the answers in them without knowing what to look for.
Bridge mode was the key.
For anyone else who stumbles here via google/search
Changed the DG834g to 'Modem Mode' via this page
-> http://192.168.0.1/setup.cgi?next_file=mode.htm'
Made sure the NAT was off, reboot the modem and set PPPoE in gargoyle and all is working fine.
i must have browsed over a ton of threads with the answers in them without knowing what to look for.
Bridge mode was the key.
For anyone else who stumbles here via google/search
Changed the DG834g to 'Modem Mode' via this page
-> http://192.168.0.1/setup.cgi?next_file=mode.htm'
Made sure the NAT was off, reboot the modem and set PPPoE in gargoyle and all is working fine.
Re: Gargoyle Router - Setup/Access questions
Ok Couple of other questions if anyone can help.
My previous Filezilla site settings to connect to the NAS seemed to work after i forwarded the port in Gargoyle.
But i had to set the Transfer Mode: Active
or i kept getting a "Server sent passive reply with unroutable address. Using server address instead." and a timeout on getting directory listing.
The login went ok up until that point.
No other settings have changed on the NAS that i am aware of.
Any ideas?
Also re Gargoyle
- Is there any way to log access (successful and attempts) ?
say to syslog on the NAS?
- Is it possible to get Quota to display data as amount rather than %
I looked about but it only seems to show %
My previous Filezilla site settings to connect to the NAS seemed to work after i forwarded the port in Gargoyle.
But i had to set the Transfer Mode: Active
or i kept getting a "Server sent passive reply with unroutable address. Using server address instead." and a timeout on getting directory listing.
The login went ok up until that point.
No other settings have changed on the NAS that i am aware of.
Any ideas?
Also re Gargoyle
- Is there any way to log access (successful and attempts) ?
say to syslog on the NAS?
- Is it possible to get Quota to display data as amount rather than %
I looked about but it only seems to show %