The Buffalo WHR-G125
Broadcom 5354 chipset
4MB Flash / 16MB Ram
Uses DD-WRT generic build, either mini or standard.
Tried flashing the broadcom generic 1.0.6 build, no luck.
I tried flashing from DD-WRT, I tried TFTP'ing the file, both
said it was successfully flashed, but the device does not boot.
Able to recover back to DD-WRT via TFTP, so not an issue.
Just letting you know currently this device won't load up
with Gargoyle - know you're busy, so whenever you got time!
Buffalo WHR-G125 - not working for install
Moderator: Moderators
- DoesItMatter
- Moderator
- Posts: 1373
- Joined: Thu May 21, 2009 3:56 pm
Buffalo WHR-G125 - not working for install
Soylent Green Is People!
2x Asus RT-N16 = Asus 3.0.0.4.374.43 Merlin
2x Buffalo WZR-HP-G300NH V1 A0D0 = Gargoyle 1.9.x / LEDE 17.01.x
2x Engenius - ESR900 Stock 1.4.0 / OpenWRT Trunk 49400
2x Asus RT-N16 = Asus 3.0.0.4.374.43 Merlin
2x Buffalo WZR-HP-G300NH V1 A0D0 = Gargoyle 1.9.x / LEDE 17.01.x
2x Engenius - ESR900 Stock 1.4.0 / OpenWRT Trunk 49400
Re: Buffalo WHR-G125 - not working for install
Does the problem arise of the WAN is disconnected? There is a report in another thread, that if the WAN is connected there are problems, but if it is disconnected, it seems to be ok.
Obviously this is a major problem... but if you're seeing the same thing, that would be helpful to know.
Obviously this is a major problem... but if you're seeing the same thing, that would be helpful to know.
- DoesItMatter
- Moderator
- Posts: 1373
- Joined: Thu May 21, 2009 3:56 pm
Re: Buffalo WHR-G125 - not working for install
Only cable I had connected was a LAN cable for flashing
WAN port was open, nothing connected yet.
When I TFP, the default IP for the WHR-G125 is 192.168.11.1
The flashing LOOKS like it works, but nothing happens.
It goes through the process, then only shows the power LED
I tried pinging 192.168.11.1, 192.168.1.1 - no luck
Easy to recover via TFTP mode though, luckily its built in
--------------------------------
Flashed 1.0.6 to my Fonera 2201+ via Fon Flash
I've never been able to upgrade the Fon via the Web GUI
Not an issue though, as I prefer wiping the nvram first.
I left the WAN connected to my cable modem
Flashed successfully, no issues, and no problems getting into
Gargoyle interface or configuring it.
Up and running for me - no issues with it not coming up.
Just doesn't work on the WHR-G125 currently, I can wait.
WAN port was open, nothing connected yet.
When I TFP, the default IP for the WHR-G125 is 192.168.11.1
The flashing LOOKS like it works, but nothing happens.
It goes through the process, then only shows the power LED
I tried pinging 192.168.11.1, 192.168.1.1 - no luck
Easy to recover via TFTP mode though, luckily its built in
--------------------------------
Flashed 1.0.6 to my Fonera 2201+ via Fon Flash
I've never been able to upgrade the Fon via the Web GUI
Not an issue though, as I prefer wiping the nvram first.
I left the WAN connected to my cable modem
Flashed successfully, no issues, and no problems getting into
Gargoyle interface or configuring it.
Up and running for me - no issues with it not coming up.
Just doesn't work on the WHR-G125 currently, I can wait.
Soylent Green Is People!
2x Asus RT-N16 = Asus 3.0.0.4.374.43 Merlin
2x Buffalo WZR-HP-G300NH V1 A0D0 = Gargoyle 1.9.x / LEDE 17.01.x
2x Engenius - ESR900 Stock 1.4.0 / OpenWRT Trunk 49400
2x Asus RT-N16 = Asus 3.0.0.4.374.43 Merlin
2x Buffalo WZR-HP-G300NH V1 A0D0 = Gargoyle 1.9.x / LEDE 17.01.x
2x Engenius - ESR900 Stock 1.4.0 / OpenWRT Trunk 49400