Gargoyle 1.15.x BETA - 2024-03-11 - Based on OpenWrt 23.05

[Lajkzy]

Thanks! Wndr3700v1 is working on this build, 1.14 didnt work at all! Very happy now

[pythonic]

inet AR150 was a bit suspect and complained about space, but seemed to run

I didn't see any space complaint when upgrading mine, but I didn't attempt to preserve the configuration. Mine ran fine with a Huawei E3372 HiLink modem as the WAN.

[ektus]

Just installed it on my spare Archer C7 V2. Seems to be running just fine without further configuration. Wifi untested.


Where to point the plugin source? Default is

Code: Select all

http://www.gargoyle-router.com/packages/gargoyle-1.16/ath79/default

which doesn't seem to be populated yet.

[Lantis]

Just installed it on my spare Archer C7 V2. Seems to be running just fine without further configuration. Wifi untested.


Where to point the plugin source? Default is

Code: Select all

http://www.gargoyle-router.com/packages/gargoyle-1.16/ath79/default

which doesn't seem to be populated yet.

In the same folder as you downloaded the image from, as per the first post.

Code: Select all

https://lantisproject.com/gargoyle_custom/1.15.x_2305_test_builds/ath79/default/
https://lantisproject.com/gargoyle_custom/1.15.x_2305_test_builds/ath79/default_kernelspecific/

[ektus]

Thank you, this did the trick. spectrum analyser is working, so wifi should be okay. Mission accomplished, spare router updated and ready for use (storage) again

[JohnPeterson]

I see the Linksys WRT1900ACS is avail again. I get screen message when attempting an upgrade.

Firmware/Device Compatibile:No. Config cannot be migrated from swconfig to DSA

Thanks.

It was also showing partition change warning - i put the factory image in /tmp and did:


sysupgrade -F -n gargoyle_1.15.x-mvebu-cortexa9-linksys_wrt1900ac-v1-squashfs-factory.img

its working! This got me from 1.13 to 1.15test

[Eric3K]

Installed on TP-Link TL-WDR4300 v1.3 without issue. No space warnings with Adblock installed and blocklist downloaded (672 KB free).

[angus]

The usteer package is installed by default on most profiles, others will need to install it.
There is no GUI configuration for usteer except for being able to turn it on and off to help send AP client information between multiple Gargoyle routers on the same network (in a multi-AP setup for example).
Search for usteer for OpenWrt and read about the configuration. The default should work for most people but your mileage may vary!

If you wanted to try DAWN instead you can but you’ll need to install that and try it.

Tested usteer and it works between 2.4G and 5G for the same SSID within a wireless router e.g. WRT3200ACM vs iPhones. Looking forward to seeing the official 1.15.
P.S. I did enable the Fast Roaming. Thought that may not be required.

[Lantis]

The usteer package is installed by default on most profiles, others will need to install it.
There is no GUI configuration for usteer except for being able to turn it on and off to help send AP client information between multiple Gargoyle routers on the same network (in a multi-AP setup for example).
Search for usteer for OpenWrt and read about the configuration. The default should work for most people but your mileage may vary!

If you wanted to try DAWN instead you can but you’ll need to install that and try it.

Tested usteer and it works between 2.4G and 5G for the same SSID within a wireless router e.g. WRT3200ACM vs iPhones. Looking forward to seeing the official 1.15.
P.S. I did enable the Fast Roaming. Thought that may not be required.

Fantastic.
Did you change any of the default settings? You must have set your SSID at a minimum I think?

[ispyisail]

Tested usteer and it works between 2.4G and 5G for the same SSID within a wireless router e.g. WRT3200ACM vs iPhones. Looking forward to seeing the official 1.15.
P.S. I did enable the Fast Roaming. Thought that may not be required.

https://openwrt.org/docs/guide-user/network/wifi/usteer