Netgear R8000
Moderator: Moderators
Re: Netgear R8000
Go through the device definitions in the OpenWrt target directory and make sure that all default and device packages have been included in the config with =y. In particular, default packages sometimes don't seem to get included in images unless they're set =y in the config.
Re: Netgear R8000
Well, it's just not going to work properly and OpenWRT is no different so it's not a Gargoyle issue. Dmesg shows brcmfmac-firmware-43602a1-pcie errors and the switch only does 100Mb/s. Even though gargoyle only gives G as an option I'm connected at 144Mb/s, same with OpenWRT although it says N.
I wanted to get rid of the MR3420 because of the MT76xx heavy load crashes which apart from the AP disappearing, it screws up the bandwidth monitor and quotas.
My internet is 4G so I have an MR6400v3 (not supported by OpenWRT) set up as a modem going into the MR3420 with Gargoyle. Because of the crashes I've had to disable wireless on the MR3420 and I've added an Asus RT-AC1200G as an AP (also not supported by OpenWRT). It's messy but it works, and the speeds to my media server are a lot faster with the Asus AP.
I don't see the point of swapping the Netgear for the Asus so it's going to get flashed back to stock firmware and sit in a box as a spare AP.
Anyway, thanks for trying to help. I've learnt a lot so I guess it wasn't a complete waste of time.
Cheers
I wanted to get rid of the MR3420 because of the MT76xx heavy load crashes which apart from the AP disappearing, it screws up the bandwidth monitor and quotas.
My internet is 4G so I have an MR6400v3 (not supported by OpenWRT) set up as a modem going into the MR3420 with Gargoyle. Because of the crashes I've had to disable wireless on the MR3420 and I've added an Asus RT-AC1200G as an AP (also not supported by OpenWRT). It's messy but it works, and the speeds to my media server are a lot faster with the Asus AP.
I don't see the point of swapping the Netgear for the Asus so it's going to get flashed back to stock firmware and sit in a box as a spare AP.
Anyway, thanks for trying to help. I've learnt a lot so I guess it wasn't a complete waste of time.
Cheers
Last edited by rg66 on Fri Jun 02, 2023 11:22 am, edited 1 time in total.
Re: Netgear R8000
That's disappointing ![Sad :(](./images/smilies/icon_e_sad.gif)
Out of curiousity, which OpenWrt versions did you try that showed the same problems?
![Sad :(](./images/smilies/icon_e_sad.gif)
Out of curiousity, which OpenWrt versions did you try that showed the same problems?
Re: Netgear R8000
The most recent one: openwrt-22.03.5-bcm53xx-generic-netgear_r8000-squashfs.chk
Re: Netgear R8000
Broadcom just is what it is unfortunately. I agree you did not waste your time in learning something ![Smile :)](./images/smilies/icon_e_smile.gif)
![Smile :)](./images/smilies/icon_e_smile.gif)
http://lantisproject.com/downloads/gargoyle_ispyisail.php for the latest releases
Please be respectful when posting. I do this in my free time on a volunteer basis.
Please be respectful when posting. I do this in my free time on a volunteer basis.
Re: Netgear R8000
If you haven't already put it back to the OEM firmware, you might consider trying the 23.05 snapshot (i.e. pre-release of 23.05, should include LuCI unlike master snapshots) from https://downloads.openwrt.org/releases/ ... x/generic/ to see whether that works any better than 22.03.5.
Re: Netgear R8000
I have put it back to stock firmware but I can flash back and forth from either GUI without any issues so I will give it a try.
Cheers
Cheers
Re: Netgear R8000
Snapshot is even worse, I keep getting "can't connect to network" and if I can manage to get connected to 2.4GHz N it doesn't give me an IP address.
I then flashed current OpenWRT and wireless was working better but same issues as previous post.
Here is dmesg from current which is basically the same as my Gargoyle builds. I'm sure you can make more sense of it than me. Sorry for the length, apparently attachments don't work.
I then flashed current OpenWRT and wireless was working better but same issues as previous post.
Here is dmesg from current which is basically the same as my Gargoyle builds. I'm sure you can make more sense of it than me. Sorry for the length, apparently attachments don't work.
Cheersroot@OpenWrt:~# dmesg
[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Linux version 5.10.176 (builder@buildhost) (arm-openwrt-linux-muslgnueabi-gcc (OpenWrt GCC 11.2.0 r20134-5f15225c1e) 11.2.0, GNU ld (GNU Binutils) 2.37) #0 SMP Thu Apr 27 20:28:15 2023
[ 0.000000] CPU: ARMv7 Processor [413fc090] revision 0 (ARMv7), cr=10c5387d
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[ 0.000000] OF: fdt: Machine model: Netgear R8000 (BCM4709)
[ 0.000000] Memory policy: Data cache writealloc
[ 0.000000] Hit pending asynchronous external abort (FSR=0x00001c06) during first unmask, this is most likely caused by a firmware/bootloader bug.
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x0000000000000000-0x0000000007ffffff]
[ 0.000000] HighMem [mem 0x0000000008000000-0x000000008fffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000000000000-0x0000000007ffffff]
[ 0.000000] node 0: [mem 0x0000000088000000-0x000000008fffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x000000008fffffff]
[ 0.000000] On node 0 totalpages: 65536
[ 0.000000] Normal zone: 288 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 32768 pages, LIFO batch:7
[ 0.000000] HighMem zone: 32768 pages, LIFO batch:7
[ 0.000000] percpu: Embedded 14 pages/cpu s27596 r8192 d21556 u57344
[ 0.000000] pcpu-alloc: s27596 r8192 d21556 u57344 alloc=14*4096
[ 0.000000] pcpu-alloc: [0] 0 [0] 1
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 65248
[ 0.000000] Kernel command line: console=ttyS0,115200
[ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes, linear)
[ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes, linear)
[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[ 0.000000] Memory: 249448K/262144K available (6236K kernel code, 571K rwdata, 816K rodata, 1024K init, 294K bss, 12696K reserved, 0K cma-reserved, 131072K highmem)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[ 0.000000] rcu: Hierarchical RCU implementation.
[ 0.000000] Tracing variant of Tasks RCU enabled.
[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies.
[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
[ 0.000000] L2C: DT/platform modifies aux control register: 0x0a130000 -> 0x3a530000
[ 0.000000] L2C-310 enabling early BRESP for Cortex-A9
[ 0.000000] L2C-310 full line of zeros enabled for Cortex-A9
[ 0.000000] L2C-310 ID prefetch enabled, offset 1 lines
[ 0.000000] L2C-310 dynamic clock gating enabled, standby mode enabled
[ 0.000000] L2C-310 cache controller enabled, 16 ways, 256 kB
[ 0.000000] L2C-310: CACHE_ID 0x410000c8, AUX_CTRL 0x7e530001
[ 0.000011] sched_clock: 64 bits at 500MHz, resolution 2ns, wraps every 4398046511103ns
[ 0.000030] clocksource: arm_global_timer: mask: 0xffffffffffffffff max_cycles: 0xe6a171a037, max_idle_ns: 881590485102 ns
[ 0.000052] Switching to timer-based delay loop, resolution 2ns
[ 0.000304] Calibrating delay loop (skipped), value calculated using timer frequency.. 1000.00 BogoMIPS (lpj=5000000)
[ 0.000319] pid_max: default: 32768 minimum: 301
[ 0.000427] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.000439] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.001095] CPU: Testing write buffer coherency: ok
[ 0.001136] CPU0: Spectre v2: using BPIALL workaround
[ 0.001375] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[ 0.001976] Setting up static identity map for 0x100000 - 0x10003c
[ 0.002121] rcu: Hierarchical SRCU implementation.
[ 0.002288] dyndbg: Ignore empty _ddebug table in a CONFIG_DYNAMIC_DEBUG_CORE build
[ 0.002463] smp: Bringing up secondary CPUs ...
[ 0.003154] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
[ 0.003162] CPU1: Spectre v2: using BPIALL workaround
[ 0.003275] smp: Brought up 1 node, 2 CPUs
[ 0.003286] SMP: Total of 2 processors activated (2000.00 BogoMIPS).
[ 0.003294] CPU: WARNING: CPU(s) started in wrong/inconsistent modes (primary CPU mode 0x13)
[ 0.003300] CPU: This may indicate a broken bootloader or firmware.
[ 0.005757] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.005783] futex hash table entries: 512 (order: 3, 32768 bytes, linear)
[ 0.005927] pinctrl core: initialized pinctrl subsystem
[ 0.006735] NET: Registered protocol family 16
[ 0.007447] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 0.008356] thermal_sys: Registered thermal governor 'step_wise'
[ 0.031300] clocksource: Switched to clocksource arm_global_timer
[ 0.032173] NET: Registered protocol family 2
[ 0.032367] IP idents hash table entries: 2048 (order: 2, 16384 bytes, linear)
[ 0.033224] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear)
[ 0.033308] TCP established hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.033330] TCP bind hash table entries: 1024 (order: 1, 8192 bytes, linear)
[ 0.033350] TCP: Hash tables configured (established 1024 bind 1024)
[ 0.033473] UDP hash table entries: 256 (order: 1, 8192 bytes, linear)
[ 0.033519] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear)
[ 0.033763] NET: Registered protocol family 1
[ 0.033797] PCI: CLS 0 bytes, default 64
[ 0.036154] workingset: timestamp_bits=14 max_order=16 bucket_order=2
[ 0.038649] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.038665] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.039225] bounce: pool size: 64 pages
[ 0.039289] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
[ 0.040995] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[ 0.042700] printk: console [ttyS0] disabled
[ 0.042779] 18000300.serial: ttyS0 at MMIO 0x18000300 (irq = 26, base_baud = 7812500) is a 16550
[ 0.562517] printk: console [ttyS0] enabled
[ 0.567684] bcm2835-rng 18004000.rng: hwrng registered
[ 0.970122] random: crng init done
[ 0.974493] nand: device found, Manufacturer ID: 0xc2, Chip ID: 0xf1
[ 0.980869] nand: Macronix NAND 128MiB 3,3V 8-bit
[ 0.985632] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
[ 0.993258] iproc_nand 18028000.nand-controller: detected 128MiB total, 128KiB blocks, 2KiB pages, 16B OOB, 8-bit, BCH-8
[ 1.004180] Block protection check failed
[ 1.008205] Scanning device for bad blocks
[ 1.063848] Bad eraseblock 86 at 0x000000ac0000
[ 1.099066] Bad eraseblock 138 at 0x000001140000
[ 1.114114] Bad eraseblock 156 at 0x000001380000
[ 1.159519] Bad eraseblock 225 at 0x000001c20000
[ 1.206145] Bad eraseblock 296 at 0x000002500000
[ 1.343458] Bad eraseblock 477 at 0x000003ba0000
[ 1.850646] mtd_read error while parsing (offset: 0xAD0000): -74
[ 1.891143] mtd_read error while parsing (offset: 0x1150000): -74
[ 1.909413] mtd_read error while parsing (offset: 0x1390000): -74
[ 1.961124] mtd_read error while parsing (offset: 0x1C30000): -74
[ 2.014145] mtd_read error while parsing (offset: 0x2510000): -74
[ 2.077675] mtd_read error while parsing (offset: 0x30A0000): -74
[ 2.166411] mtd_read error while parsing (offset: 0x3BB0000): -74
[ 2.673463] 15 bcm47xxpart partitions found on MTD device brcmnand.0
[ 2.679838] Creating 15 MTD partitions on "brcmnand.0":
[ 2.685089] 0x000000000000-0x000000080000 : "boot"
[ 2.690562] 0x000000080000-0x000000200000 : "nvram"
[ 2.696136] 0x000000200000-0x000002600000 : "firmware"
[ 2.702734] 2 trx partitions found on MTD device firmware
[ 2.708150] Creating 2 MTD partitions on "firmware":
[ 2.713154] 0x00000000001c-0x000000400000 : "linux"
[ 2.718047] mtd: partition "linux" doesn't start on an erase/write block boundary -- force read-only
[ 2.727862] 0x000000400000-0x000002400000 : "ubi"
[ 2.733346] 0x000002600000-0x000002680000 : "board_data"
[ 2.739354] 0x000002680000-0x0000026a0000 : "POT"
[ 2.744818] 0x0000026a0000-0x000002780000 : "POT"
[ 2.750211] 0x000002780000-0x0000027a0000 : "POT"
[ 2.755771] 0x0000027a0000-0x000002e00000 : "POT"
[ 2.761223] 0x000002e00000-0x000002e80000 : "ML"
[ 2.766544] 0x000002e80000-0x000002f00000 : "ML"
[ 2.771908] 0x000002f00000-0x000002f80000 : "ML"
[ 2.777214] 0x000002f80000-0x000003000000 : "ML"
[ 2.782569] 0x000003000000-0x000003080000 : "ML"
[ 2.787904] 0x000003080000-0x000003100000 : "ML"
[ 2.793241] 0x000003100000-0x000008000000 : "ML"
[ 2.803502] bcm_iproc 18029200.spi: using bspi-mspi mode
[ 2.811250] iproc-mdio 18003000.mdio: Broadcom iProc MDIO bus registered
[ 2.819723] b53-srab-switch 18007000.ethernet-switch: found switch: BCM53012, rev 5
[ 2.827625] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded
[ 2.833799] bcma-host-soc 18000000.axi: bus0: Found chip with id 53010, rev 0x00 and package 0x00
[ 2.842805] bcma-host-soc 18000000.axi: bus0: Core 0 found: ChipCommon (manuf 0x4BF, id 0x800, rev 0x2A, class 0x0)
[ 2.853427] bcma-host-soc 18000000.axi: bus0: bcma_of_get_irq() failed with rc=-22
[ 2.853439] bcma-host-soc 18000000.axi: bus0: Core 1 found: Chipcommon B (manuf 0x4BF, id 0x50B, rev 0x01, class 0x0)
[ 2.864207] bcma-host-soc 18000000.axi: bus0: bcma_of_get_irq() failed with rc=-22
[ 2.864217] bcma-host-soc 18000000.axi: bus0: Core 2 found: DMA (manuf 0x4BF, id 0x502, rev 0x01, class 0x0)
[ 2.874239] bcma-host-soc 18000000.axi: bus0: Core 3 found: GBit MAC (manuf 0x4BF, id 0x82D, rev 0x05, class 0x0)
[ 2.884697] bcma-host-soc 18000000.axi: bus0: Core 4 found: GBit MAC (manuf 0x4BF, id 0x82D, rev 0x05, class 0x0)
[ 2.895138] bcma-host-soc 18000000.axi: bus0: Core 5 found: GBit MAC (manuf 0x4BF, id 0x82D, rev 0x05, class 0x0)
[ 2.905584] bcma-host-soc 18000000.axi: bus0: Core 6 found: GBit MAC (manuf 0x4BF, id 0x82D, rev 0x05, class 0x0)
[ 2.915968] bcma-host-soc 18000000.axi: bus0: Core 7 found: PCIe Gen 2 (manuf 0x4BF, id 0x501, rev 0x01, class 0x0)
[ 2.926527] bcma-host-soc 18000000.axi: bus0: Core 8 found: PCIe Gen 2 (manuf 0x4BF, id 0x501, rev 0x01, class 0x0)
[ 2.937102] bcma-host-soc 18000000.axi: bus0: Core 9 found: PCIe Gen 2 (manuf 0x4BF, id 0x501, rev 0x01, class 0x0)
[ 2.947699] bcma-host-soc 18000000.axi: bus0: bcma_of_get_irq() failed with rc=-22
[ 2.947710] bcma-host-soc 18000000.axi: bus0: Core 10 found: ARM Cortex A9 core (ihost) (manuf 0x4BF, id 0x510, rev 0x01, class 0x0)
[ 2.959772] bcma-host-soc 18000000.axi: bus0: Core 11 found: USB 2.0 (manuf 0x4BF, id 0x504, rev 0x01, class 0x0)
[ 2.970181] bcma-host-soc 18000000.axi: bus0: Core 12 found: USB 3.0 (manuf 0x4BF, id 0x505, rev 0x01, class 0x0)
[ 2.980602] bcma-host-soc 18000000.axi: bus0: bcma_of_get_irq() failed with rc=-22
[ 2.980612] bcma-host-soc 18000000.axi: bus0: Core 13 found: SDIO3 (manuf 0x4BF, id 0x503, rev 0x01, class 0x0)
[ 2.990856] bcma-host-soc 18000000.axi: bus0: bcma_of_get_irq() failed with rc=-22
[ 2.990867] bcma-host-soc 18000000.axi: bus0: Core 14 found: I2S (manuf 0x4BF, id 0x834, rev 0x03, class 0x0)
[ 3.000937] bcma-host-soc 18000000.axi: bus0: bcma_of_get_irq() failed with rc=-22
[ 3.000947] bcma-host-soc 18000000.axi: bus0: Core 15 found: ARM Cortex A9 JTAG (manuf 0x4BF, id 0x506, rev 0x01, class 0x0)
[ 3.012322] bcma-host-soc 18000000.axi: bus0: bcma_of_get_irq() failed with rc=-22
[ 3.012332] bcma-host-soc 18000000.axi: bus0: Core 16 found: Denali DDR2/DDR3 memory controller (manuf 0x4BF, id 0x507, rev 0x01, class 0x0)
[ 3.025104] bcma-host-soc 18000000.axi: bus0: bcma_of_get_irq() failed with rc=-22
[ 3.025115] bcma-host-soc 18000000.axi: bus0: Core 17 found: ROM (manuf 0x4BF, id 0x508, rev 0x01, class 0x0)
[ 3.035220] bcma-host-soc 18000000.axi: bus0: Core 18 found: NAND flash controller (manuf 0x4BF, id 0x509, rev 0x01, class 0x0)
[ 3.046859] bcma-host-soc 18000000.axi: bus0: bcma_of_get_irq() failed with rc=-22
[ 3.046870] bcma-host-soc 18000000.axi: bus0: Core 19 found: SPI flash controller (manuf 0x4BF, id 0x50A, rev 0x01, class 0x0)
[ 3.058315] bcma-host-soc 18000000.axi: bus0: Flash type not supported
[ 3.088919] bcma-host-soc 18000000.axi: bus0: Using SPROM revision 11 provided by platform.
[ 3.089214] bgmac_bcma bcma0:3: Found PHY addr: 30 (NOREGS)
[ 3.094852] bgmac_bcma bcma0:3: Support for Roboswitch not implemented
[ 3.101417] bgmac_bcma bcma0:3: Invalid MAC addr: 00:00:00:00:00:00
[ 3.107704] bgmac_bcma bcma0:3: Using random MAC: 3a:a4:d0:50:48:bf
[ 3.115174] b53-srab-switch b53-srab-switch: invalid resource
[ 3.120963] b53-srab-switch: probe of b53-srab-switch failed with error -22
[ 3.128695] bgmac_bcma bcma0:4: Found PHY addr: 30 (NOREGS)
[ 3.134337] bgmac_bcma bcma0:4: Support for Roboswitch not implemented
[ 3.140892] bgmac_bcma bcma0:4: Invalid MAC addr: 00:00:00:00:00:00
[ 3.147188] bgmac_bcma bcma0:4: Using random MAC: 86:30:33:45:29:ef
[ 3.155293] bgmac_bcma bcma0:5: Found PHY addr: 30 (NOREGS)
[ 3.160903] bgmac_bcma bcma0:5: Support for Roboswitch not implemented
[ 3.169209] bgmac_bcma bcma0:6: Unsupported core_unit 3
[ 3.174561] bgmac_bcma: probe of bcma0:6 failed with error -524
[ 3.180616] pcie_iproc_bcma bcma0:7: host bridge /axi@18000000/pcie@12000 ranges:
[ 3.188167] pcie_iproc_bcma bcma0:7: No bus range found for /axi@18000000/pcie@12000, using [bus 00-ff]
[ 3.197780] OF: /axi@18000000/pcie@12000: Missing device_type
[ 3.203551] pcie_iproc_bcma bcma0:7: non-prefetchable memory resource required
[ 3.321176] pcie_iproc_bcma bcma0:7: link: UP
[ 3.325679] pcie_iproc_bcma bcma0:7: PCI host bridge to bus 0000:00
[ 3.331993] pci_bus 0000:00: root bus resource [bus 00-ff]
[ 3.337497] pci_bus 0000:00: root bus resource [mem 0x08000000-0x0fffffff]
[ 3.344429] pci 0000:00:00.0: [14e4:8012] type 01 class 0x060400
[ 3.350458] pci_bus 0000:00: 2-byte config write to 0000:00:00.0 offset 0x4 may corrupt adjacent RW1C bits
[ 3.360190] pci 0000:00:00.0: PME# supported from D0 D3hot D3cold
[ 3.367272] PCI: bus0: Fast back to back transfers disabled
[ 3.372889] pci 0000:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[ 3.381066] pci 0000:01:00.0: [14e4:aa52] type 00 class 0x028000
[ 3.387120] pci_bus 0000:01: 2-byte config write to 0000:01:00.0 offset 0x4 may corrupt adjacent RW1C bits
[ 3.396832] pci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x00007fff 64bit]
[ 3.403652] pci 0000:01:00.0: reg 0x18: [mem 0x00000000-0x003fffff 64bit]
[ 3.410562] pci 0000:01:00.0: supports D1 D2
[ 3.415798] PCI: bus1: Fast back to back transfers disabled
[ 3.421416] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01
[ 3.428074] pci 0000:00:00.0: BAR 8: assigned [mem 0x08000000-0x085fffff]
[ 3.434897] pci 0000:01:00.0: BAR 2: assigned [mem 0x08000000-0x083fffff 64bit]
[ 3.442253] pci 0000:01:00.0: BAR 0: assigned [mem 0x08400000-0x08407fff 64bit]
[ 3.449593] pci 0000:00:00.0: PCI bridge to [bus 01]
[ 3.454582] pci 0000:00:00.0: bridge window [mem 0x08000000-0x085fffff]
[ 3.461609] pcie_iproc_bcma bcma0:8: host bridge /axi@18000000/pcie@13000 ranges:
[ 3.469127] pcie_iproc_bcma bcma0:8: No bus range found for /axi@18000000/pcie@13000, using [bus 00-ff]
[ 3.478740] pcie_iproc_bcma bcma0:8: non-prefetchable memory resource required
[ 3.611173] pcie_iproc_bcma bcma0:8: link: UP
[ 3.615685] pcie_iproc_bcma bcma0:8: PCI host bridge to bus 0001:00
[ 3.622002] pci_bus 0001:00: root bus resource [bus 00-ff]
[ 3.627505] pci_bus 0001:00: root bus resource [mem 0x40000000-0x47ffffff]
[ 3.634434] pci 0001:00:00.0: [14e4:8012] type 01 class 0x060400
[ 3.640457] pci_bus 0001:00: 2-byte config write to 0001:00:00.0 offset 0x4 may corrupt adjacent RW1C bits
[ 3.650189] pci 0001:00:00.0: PME# supported from D0 D3hot D3cold
[ 3.657268] PCI: bus0: Fast back to back transfers disabled
[ 3.662884] pci 0001:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[ 3.671068] pci 0001:01:00.0: [10b5:8603] type 01 class 0x060400
[ 3.677130] pci_bus 0001:01: 2-byte config write to 0001:01:00.0 offset 0x4 may corrupt adjacent RW1C bits
[ 3.686840] pci 0001:01:00.0: reg 0x10: [mem 0x00000000-0x00003fff]
[ 3.693262] pci 0001:01:00.0: supports D1 D2
[ 3.697543] pci 0001:01:00.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 3.705154] PCI: bus1: Fast back to back transfers disabled
[ 3.710753] pci 0001:01:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[ 3.718975] pci 0001:02:00.0: [0000:0012] type 12 class 0x001200
[ 3.725029] pci_bus 0001:02: 2-byte config write to 0001:02:00.0 offset 0x4 may corrupt adjacent RW1C bits
[ 3.734728] pci 0001:02:00.0: unknown header type 12, ignoring device
[ 3.741298] pci 0001:02:01.0: [10b5:8603] type 01 class 0x060400
[ 3.747473] pci 0001:02:01.0: supports D1 D2
[ 3.751762] pci 0001:02:01.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 3.758641] pci 0001:02:02.0: [10b5:8603] type 01 class 0x060400
[ 3.764837] pci 0001:02:02.0: supports D1 D2
[ 3.769117] pci 0001:02:02.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 3.776057] pci 0001:02:03.0: [0008:0000] type 00 class 0x000000
[ 3.782381] pci 0001:02:04.0: [0008:0000] type 00 class 0x000000
[ 3.788693] pci 0001:02:05.0: [0008:0000] type 00 class 0x000000
[ 3.795016] pci 0001:02:06.0: [0008:0000] type 00 class 0x000000
[ 3.801360] pci 0001:02:07.0: [0008:0000] type 00 class 0x000000
[ 3.807658] pci 0001:02:08.0: [0008:0000] type 00 class 0x000000
[ 3.813995] pci 0001:02:09.0: [0008:0000] type 00 class 0x000000
[ 3.820297] pci 0001:02:0a.0: [0008:0000] type 00 class 0x000000
[ 3.826645] pci 0001:02:0b.0: [0008:0000] type 00 class 0x000000
[ 3.832967] pci 0001:02:0c.0: [0008:0000] type 00 class 0x000000
[ 3.839280] pci 0001:02:0d.0: [0008:0000] type 00 class 0x000000
[ 3.845615] pci 0001:02:0e.0: [0008:0000] type 00 class 0x000000
[ 3.851942] pci 0001:02:0f.0: [0008:0000] type 00 class 0x000000
[ 3.858257] pci 0001:02:10.0: [0008:0000] type 00 class 0x000000
[ 3.864593] pci 0001:02:11.0: [0008:0000] type 00 class 0x000000
[ 3.870897] pci 0001:02:12.0: [0008:0000] type 00 class 0x000000
[ 3.877220] pci 0001:02:13.0: [0008:0000] type 00 class 0x000000
[ 3.883559] pci 0001:02:14.0: [0008:0000] type 00 class 0x000000
[ 3.889865] pci 0001:02:15.0: [0008:0000] type 00 class 0x000000
[ 3.896194] pci 0001:02:16.0: [0008:0000] type 00 class 0x000000
[ 3.902519] pci 0001:02:17.0: [0008:0000] type 00 class 0x000000
[ 3.908824] pci 0001:02:18.0: [0008:0000] type 00 class 0x000000
[ 3.915197] pci 0001:02:19.0: [0008:0000] type 00 class 0x000000
[ 3.921529] pci 0001:02:1a.0: [0008:0000] type 00 class 0x000000
[ 3.927837] pci 0001:02:1b.0: [0008:0000] type 00 class 0x000000
[ 3.934159] pci 0001:02:1c.0: [0008:0000] type 00 class 0x000000
[ 3.940477] pci 0001:02:1d.0: [0008:0000] type 00 class 0x000000
[ 3.946798] pci 0001:02:1e.0: [0008:0000] type 00 class 0x000000
[ 3.953145] pci 0001:02:1f.0: [0008:0000] type 00 class 0x000000
[ 3.959674] PCI: bus2: Fast back to back transfers disabled
[ 3.965289] pci 0001:02:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[ 3.973339] pci 0001:02:02.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[ 3.981589] pci 0001:03:00.0: [14e4:aa52] type 00 class 0x028000
[ 3.987622] pci_bus 0001:03: 2-byte config write to 0001:03:00.0 offset 0x4 may corrupt adjacent RW1C bits
[ 3.997355] pci 0001:03:00.0: reg 0x10: [mem 0x00000000-0x00007fff 64bit]
[ 4.004187] pci 0001:03:00.0: reg 0x18: [mem 0x00000000-0x003fffff 64bit]
[ 4.011176] pci 0001:03:00.0: supports D1 D2
[ 4.016424] PCI: bus3: Fast back to back transfers disabled
[ 4.022043] pci_bus 0001:03: busn_res: [bus 03-ff] end is updated to 03
[ 4.028893] pci 0001:04:00.0: [14e4:aa52] type 00 class 0x028000
[ 4.034952] pci_bus 0001:04: 2-byte config write to 0001:04:00.0 offset 0x4 may corrupt adjacent RW1C bits
[ 4.044672] pci 0001:04:00.0: reg 0x10: [mem 0x00000000-0x00007fff 64bit]
[ 4.051497] pci 0001:04:00.0: reg 0x18: [mem 0x00000000-0x003fffff 64bit]
[ 4.058471] pci 0001:04:00.0: supports D1 D2
[ 4.063765] PCI: bus4: Fast back to back transfers disabled
[ 4.069370] pci_bus 0001:04: busn_res: [bus 04-ff] end is updated to 04
[ 4.076034] pci_bus 0001:02: busn_res: [bus 02-ff] end is updated to 04
[ 4.082677] pci_bus 0001:01: busn_res: [bus 01-ff] end is updated to 04
[ 4.089386] pci 0001:00:00.0: BAR 8: assigned [mem 0x40000000-0x40cfffff]
[ 4.096218] pci 0001:00:00.0: BAR 9: assigned [mem 0x40d00000-0x40efffff 64bit pref]
[ 4.103996] pci 0001:01:00.0: BAR 8: assigned [mem 0x40000000-0x40bfffff]
[ 4.110803] pci 0001:01:00.0: BAR 9: assigned [mem 0x40d00000-0x40efffff 64bit pref]
[ 4.118574] pci 0001:01:00.0: BAR 0: assigned [mem 0x40c00000-0x40c03fff]
[ 4.125392] pci 0001:01:00.0: BAR 7: no space for [io size 0x1000]
[ 4.131680] pci 0001:01:00.0: BAR 7: failed to assign [io size 0x1000]
[ 4.138323] pci 0001:02:01.0: BAR 8: assigned [mem 0x40000000-0x405fffff]
[ 4.145140] pci 0001:02:02.0: BAR 8: assigned [mem 0x40600000-0x40bfffff]
[ 4.151958] pci 0001:02:01.0: BAR 9: assigned [mem 0x40d00000-0x40efffff 64bit pref]
[ 4.159718] pci 0001:02:01.0: BAR 7: no space for [io size 0x1000]
[ 4.166008] pci 0001:02:01.0: BAR 7: failed to assign [io size 0x1000]
[ 4.172645] pci 0001:03:00.0: BAR 2: assigned [mem 0x40000000-0x403fffff 64bit]
[ 4.179989] pci 0001:03:00.0: BAR 0: assigned [mem 0x40400000-0x40407fff 64bit]
[ 4.187341] pci 0001:02:01.0: PCI bridge to [bus 03]
[ 4.192325] pci 0001:02:01.0: bridge window [mem 0x40000000-0x405fffff]
[ 4.199131] pci 0001:02:01.0: bridge window [mem 0x40d00000-0x40efffff 64bit pref]
[ 4.206909] pci 0001:04:00.0: BAR 2: assigned [mem 0x40800000-0x40bfffff 64bit]
[ 4.214269] pci 0001:04:00.0: BAR 0: assigned [mem 0x40600000-0x40607fff 64bit]
[ 4.221616] pci 0001:02:02.0: PCI bridge to [bus 04]
[ 4.226594] pci 0001:02:02.0: bridge window [mem 0x40600000-0x40bfffff]
[ 4.233422] pci 0001:01:00.0: PCI bridge to [bus 02-04]
[ 4.238667] pci 0001:01:00.0: bridge window [mem 0x40000000-0x40bfffff]
[ 4.245479] pci 0001:01:00.0: bridge window [mem 0x40d00000-0x40efffff 64bit pref]
[ 4.253252] pci 0001:00:00.0: PCI bridge to [bus 01-04]
[ 4.258492] pci 0001:00:00.0: bridge window [mem 0x40000000-0x40cfffff]
[ 4.265304] pci 0001:00:00.0: bridge window [mem 0x40d00000-0x40efffff 64bit pref]
[ 4.273498] pcie_iproc_bcma bcma0:9: host bridge /axi@18000000/pcie@14000 ranges:
[ 4.281019] pcie_iproc_bcma bcma0:9: No bus range found for /axi@18000000/pcie@14000, using [bus 00-ff]
[ 4.290635] pcie_iproc_bcma bcma0:9: non-prefetchable memory resource required
[ 4.421174] pcie_iproc_bcma bcma0:9: PHY or data link is INACTIVE!
[ 4.427374] pcie_iproc_bcma bcma0:9: no PCIe EP device detected
[ 4.434270] bcm47xx-wdt bcm47xx-wdt.0: BCM47xx Watchdog Timer enabled (30 seconds, Software Timer)
[ 4.443343] bcma-host-soc 18000000.axi: bus0: Bus registered
[ 4.450036] NET: Registered protocol family 10
[ 4.455673] Segment Routing with IPv6
[ 4.459411] NET: Registered protocol family 17
[ 4.463955] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
[ 4.477162] 8021q: 802.1Q VLAN Support v1.8
[ 4.481455] Registering SWP/SWPB emulation handler
[ 4.489549] b53-srab-switch 18007000.ethernet-switch: found switch: BCM53012, rev 5
[ 4.624947] b53-srab-switch 18007000.ethernet-switch lan1 (uninitialized): PHY [dsa-0.0:00] driver [Generic PHY] (irq=POLL)
[ 4.637449] b53-srab-switch 18007000.ethernet-switch lan2 (uninitialized): PHY [dsa-0.0:01] driver [Generic PHY] (irq=POLL)
[ 4.649934] b53-srab-switch 18007000.ethernet-switch lan3 (uninitialized): PHY [dsa-0.0:02] driver [Generic PHY] (irq=POLL)
[ 4.662409] b53-srab-switch 18007000.ethernet-switch lan4 (uninitialized): PHY [dsa-0.0:03] driver [Generic PHY] (irq=POLL)
[ 4.674975] b53-srab-switch 18007000.ethernet-switch wan (uninitialized): PHY [dsa-0.0:04] driver [Generic PHY] (irq=POLL)
[ 4.686847] b53-srab-switch 18007000.ethernet-switch: Using legacy PHYLIB callbacks. Please migrate to PHYLINK!
[ 4.697747] DSA: tree 0 setup
[ 4.701464] UBI: auto-attach mtd4
[ 4.704803] ubi0: attaching mtd4
[ 4.873203] ubi0: scanning is finished
[ 4.885495] ubi0: attached mtd4 (name "ubi", size 32 MiB)
[ 4.890926] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
[ 4.897842] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
[ 4.904657] ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
[ 4.911644] ubi0: good PEBs: 251, bad PEBs: 5, corrupted PEBs: 0
[ 4.917661] ubi0: user volume: 2, internal volumes: 1, max. volumes count: 128
[ 4.924909] ubi0: max/mean erase counter: 3/1, WL threshold: 4096, image sequence number: 808879844
[ 4.933979] ubi0: available PEBs: 0, total reserved PEBs: 251, PEBs reserved for bad PEB handling: 15
[ 4.943265] ubi0: background thread "ubi_bgt0d" started, PID 546
[ 4.950178] block ubiblock0_0: created from ubi0:0(rootfs)
[ 4.955716] ubiblock: device ubiblock0_0 (rootfs) set to be root filesystem
[ 4.966256] VFS: Mounted root (squashfs filesystem) readonly on device 254:0.
[ 4.974398] Freeing unused kernel memory: 1024K
[ 5.001372] Run /sbin/init as init process
[ 5.005483] with arguments:
[ 5.005487] /sbin/init
[ 5.005490] with environment:
[ 5.005493] HOME=/
[ 5.005496] TERM=linux
[ 5.251556] init: Console is alive
[ 5.255182] init: - watchdog -
[ 5.603141] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[ 5.677752] bcma_hcd bcma0:12: error -EBUSY: error obtaining VCC GPIO
[ 5.684288] bcma_hcd: probe of bcma0:12 failed with error -16
[ 5.695532] usbcore: registered new interface driver usbfs
[ 5.701128] usbcore: registered new interface driver hub
[ 5.706565] usbcore: registered new device driver usb
[ 5.715103] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 5.722561] fsl-ehci: Freescale EHCI Host controller driver
[ 5.729056] ehci-platform: EHCI generic platform driver
[ 5.738322] ehci-platform 18021000.usb: EHCI Host Controller
[ 5.741132] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 5.744132] ehci-platform 18021000.usb: new USB bus registered, assigned bus number 1
[ 5.751535] ohci-platform: OHCI generic platform driver
[ 5.758342] ehci-platform 18021000.usb: irq 45, io mem 0x18021000
[ 5.763635] ohci-platform 18022000.usb: Generic Platform OHCI controller
[ 5.776331] ohci-platform 18022000.usb: new USB bus registered, assigned bus number 2
[ 5.784308] ohci-platform 18022000.usb: irq 45, io mem 0x18022000
[ 5.791242] ehci-platform 18021000.usb: USB 2.0 started, EHCI 1.00
[ 5.797989] hub 1-0:1.0: USB hub found
[ 5.801915] hub 1-0:1.0: 2 ports detected
[ 5.865787] hub 2-0:1.0: USB hub found
[ 5.869604] hub 2-0:1.0: 2 ports detected
[ 5.881684] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[ 5.898554] init: - preinit -
[ 7.174721] b53-srab-switch 18007000.ethernet-switch lan1: configuring for phy/gmii link mode
[ 7.183374] bgmac_bcma bcma0:5 eth2: Link is Up - 1Gbps/Full - flow control off
[ 7.190856] 8021q: adding VLAN 0 to HW filter on device lan1
[ 7.197706] b53-srab-switch 18007000.ethernet-switch lan1: Link is Up - 100Mbps/Full - flow control rx/tx
[ 7.261294] IPv6: ADDRCONF(NETDEV_CHANGE): eth2: link becomes ready
[ 7.267786] IPv6: ADDRCONF(NETDEV_CHANGE): lan1: link becomes ready
[ 11.463948] UBIFS (ubi0:1): default file-system created
[ 11.469907] UBIFS (ubi0:1): Mounting in unauthenticated mode
[ 11.475716] UBIFS (ubi0:1): background thread "ubifs_bgt0_1" started, PID 697
[ 11.539589] UBIFS (ubi0:1): UBIFS: mounted UBI device 0, volume 1, name "rootfs_data"
[ 11.547488] UBIFS (ubi0:1): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
[ 11.557443] UBIFS (ubi0:1): FS size: 23998464 bytes (22 MiB, 189 LEBs), journal size 1142784 bytes (1 MiB, 9 LEBs)
[ 11.567822] UBIFS (ubi0:1): reserved for root: 1133506 bytes (1106 KiB)
[ 11.574466] UBIFS (ubi0:1): media format: w5/r0 (latest is w5/r0), UUID 1C01857C-B7E5-4A2E-8F3E-62C9EE461BE9, small LPT model
[ 11.587679] mount_root: overlay filesystem has not been fully initialized yet
[ 11.595284] mount_root: switching to ubifs overlay
[ 11.604991] urandom-seed: Seed file not found (/etc/urandom.seed)
[ 11.676272] b53-srab-switch 18007000.ethernet-switch lan1: Link is Down
[ 11.775534] procd: - early -
[ 11.778556] procd: - watchdog -
[ 12.367272] procd: - watchdog -
[ 12.433568] procd: - ubus -
[ 12.491976] procd: - init -
[ 12.989725] urngd: v1.0.2 started.
[ 13.049885] kmodloader: loading kernel modules from /etc/modules.d/*
[ 13.124727] Loading modules backported from Linux version v5.15.92-0-ge515b9902f5f
[ 13.132378] Backport generated by backports.git v5.15.92-1-0-gdfe0f60c
[ 13.180723] PPP generic driver version 2.4.2
[ 13.186120] NET: Registered protocol family 24
[ 13.195466] usbcore: registered new interface driver brcmfmac
[ 13.201441] pci 0000:00:00.0: enabling device (0140 -> 0142)
[ 13.207124] brcmfmac 0000:01:00.0: enabling device (0140 -> 0142)
[ 13.331443] brcmfmac: brcmf_fw_alloc_request: using brcm/brcmfmac43602-pcie for chip BCM43602/1
[ 13.340348] brcmfmac 0000:01:00.0: Direct firmware load for brcm/brcmfmac43602-pcie.netgear,r8000.bin failed with error -2
[ 13.508014] brcmfmac 0000:01:00.0: Direct firmware load for brcm/brcmfmac43602-pcie.netgear,r8000.txt failed with error -2
[ 13.519218] brcmfmac 0000:01:00.0: Direct firmware load for brcm/brcmfmac43602-pcie.txt failed with error -2
[ 13.635026] brcmfmac: brcmf_fw_alloc_request: using brcm/brcmfmac43602-pcie for chip BCM43602/1
[ 13.643900] brcmfmac: brcmf_c_process_clm_blob: no clm_blob available (err=-2), device may have limited channels available
[ 13.655552] brcmfmac: brcmf_c_preinit_dcmds: Firmware: BCM43602/1 wl0: Sep 18 2015 03:30:01 version 7.35.177.56 (r587209) FWID 01-6cb8e269
[ 13.682698] pci 0001:00:00.0: enabling device (0140 -> 0142)
[ 13.688404] pci 0001:01:00.0: enabling device (0140 -> 0142)
[ 13.694149] pci 0001:02:01.0: enabling device (0140 -> 0142)
[ 13.699837] brcmfmac 0001:03:00.0: enabling device (0140 -> 0142)
[ 13.831474] brcmfmac: brcmf_fw_alloc_request: using brcm/brcmfmac43602-pcie for chip BCM43602/1
[ 13.840342] brcmfmac 0001:03:00.0: Direct firmware load for brcm/brcmfmac43602-pcie.netgear,r8000.bin failed with error -2
[ 13.853246] brcmfmac 0001:03:00.0: Direct firmware load for brcm/brcmfmac43602-pcie.netgear,r8000.txt failed with error -2
[ 13.864453] brcmfmac 0001:03:00.0: Direct firmware load for brcm/brcmfmac43602-pcie.txt failed with error -2
[ 13.977284] brcmfmac: brcmf_fw_alloc_request: using brcm/brcmfmac43602-pcie for chip BCM43602/1
[ 13.986132] brcmfmac: brcmf_c_process_clm_blob: no clm_blob available (err=-2), device may have limited channels available
[ 13.998020] brcmfmac: brcmf_c_preinit_dcmds: Firmware: BCM43602/1 wl0: Sep 18 2015 03:30:01 version 7.35.177.56 (r587209) FWID 01-6cb8e269
[ 14.030045] pci 0001:02:02.0: enabling device (0140 -> 0142)
[ 14.035811] brcmfmac 0001:04:00.0: enabling device (0140 -> 0142)
[ 14.161580] brcmfmac: brcmf_fw_alloc_request: using brcm/brcmfmac43602-pcie for chip BCM43602/1
[ 14.170409] brcmfmac 0001:04:00.0: Direct firmware load for brcm/brcmfmac43602-pcie.netgear,r8000.bin failed with error -2
[ 14.183135] brcmfmac 0001:04:00.0: Direct firmware load for brcm/brcmfmac43602-pcie.netgear,r8000.txt failed with error -2
[ 14.194339] brcmfmac 0001:04:00.0: Direct firmware load for brcm/brcmfmac43602-pcie.txt failed with error -2
[ 14.325845] brcmfmac: brcmf_fw_alloc_request: using brcm/brcmfmac43602-pcie for chip BCM43602/1
[ 14.334773] brcmfmac: brcmf_c_process_clm_blob: no clm_blob available (err=-2), device may have limited channels available
[ 14.346691] brcmfmac: brcmf_c_preinit_dcmds: Firmware: BCM43602/1 wl0: Sep 18 2015 03:30:01 version 7.35.177.56 (r587209) FWID 01-6cb8e269
[ 14.381155] kmodloader: done loading kernel modules from /etc/modules.d/*
[ 25.546404] bgmac_bcma bcma0:5 eth2: Link is Up - 1Gbps/Full - flow control off
[ 25.554371] IPv6: ADDRCONF(NETDEV_CHANGE): eth2: link becomes ready
[ 25.563646] b53-srab-switch 18007000.ethernet-switch lan1: configuring for phy/gmii link mode
[ 25.577460] 8021q: adding VLAN 0 to HW filter on device lan1
[ 25.641661] br-lan: port 1(lan1) entered blocking state
[ 25.646918] br-lan: port 1(lan1) entered disabled state
[ 25.652625] device lan1 entered promiscuous mode
[ 25.657278] device eth2 entered promiscuous mode
[ 25.785291] b53-srab-switch 18007000.ethernet-switch lan2: configuring for phy/gmii link mode
[ 25.805702] 8021q: adding VLAN 0 to HW filter on device lan2
[ 25.871735] br-lan: port 2(lan2) entered blocking state
[ 25.877042] br-lan: port 2(lan2) entered disabled state
[ 25.882725] device lan2 entered promiscuous mode
[ 25.976611] b53-srab-switch 18007000.ethernet-switch lan3: configuring for phy/gmii link mode
[ 26.000567] 8021q: adding VLAN 0 to HW filter on device lan3
[ 26.091324] br-lan: port 3(lan3) entered blocking state
[ 26.096581] br-lan: port 3(lan3) entered disabled state
[ 26.102203] device lan3 entered promiscuous mode
[ 26.186021] leds bcm53xx:white:usb2: Failed to get trigger sources for /leds/usb2
[ 26.193674] leds bcm53xx:white:usb2: Failed to get trigger sources for /leds/usb2
[ 26.199877] b53-srab-switch 18007000.ethernet-switch lan4: configuring for phy/gmii link mode
[ 26.201298] leds bcm53xx:white:usb2: Failed to get trigger sources for /leds/usb2
[ 26.210912] 8021q: adding VLAN 0 to HW filter on device lan4
[ 26.217420] leds bcm53xx:white:usb2: Failed to get trigger sources for /leds/usb2
[ 26.245512] leds bcm53xx:white:usb3: Failed to get trigger sources for /leds/usb3
[ 26.253156] leds bcm53xx:white:usb3: Failed to get trigger sources for /leds/usb3
[ 26.260717] leds bcm53xx:white:usb3: Failed to get trigger sources for /leds/usb3
[ 26.268454] leds bcm53xx:white:usb3: Failed to get trigger sources for /leds/usb3
[ 26.323904] br-lan: port 4(lan4) entered blocking state
[ 26.329182] br-lan: port 4(lan4) entered disabled state
[ 26.334866] device lan4 entered promiscuous mode
[ 26.451529] b53-srab-switch 18007000.ethernet-switch wan: configuring for phy/gmii link mode
[ 26.460301] 8021q: adding VLAN 0 to HW filter on device wan
[ 30.792217] b53-srab-switch 18007000.ethernet-switch lan1: Link is Up - 100Mbps/Full - flow control rx/tx
[ 30.801991] br-lan: port 1(lan1) entered blocking state
[ 30.807272] br-lan: port 1(lan1) entered forwarding state
[ 30.814991] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[ 76.924500] br-lan: port 5(wlan1) entered blocking state
[ 76.929915] br-lan: port 5(wlan1) entered disabled state
[ 76.935514] device wlan1 entered promiscuous mode
[ 77.009341] IPv6: ADDRCONF(NETDEV_CHANGE): wlan1: link becomes ready
[ 77.015926] br-lan: port 5(wlan1) entered blocking state
[ 77.021290] br-lan: port 5(wlan1) entered forwarding state
[ 141.031618] b53-srab-switch 18007000.ethernet-switch lan1: Link is Down
[ 141.038319] br-lan: port 1(lan1) entered disabled state
[ 158.871453] device wlan1 left promiscuous mode
[ 158.876017] br-lan: port 5(wlan1) entered disabled state
[ 161.326789] br-lan: port 5(wlan1) entered blocking state
[ 161.332168] br-lan: port 5(wlan1) entered disabled state
[ 161.337699] device wlan1 entered promiscuous mode
[ 162.763565] IPv6: ADDRCONF(NETDEV_CHANGE): wlan1: link becomes ready
[ 162.770121] br-lan: port 5(wlan1) entered blocking state
[ 162.775488] br-lan: port 5(wlan1) entered forwarding state
Re: Netgear R8000
I'd seen some bcm53xx activity in OpenWrt master before the 23.05 branch so thought there may have been some hope of improvement - clearly not ![Sad :(](./images/smilies/icon_e_sad.gif)
![Sad :(](./images/smilies/icon_e_sad.gif)
Re: Netgear R8000
As Lantis said, it is what it is. If I could get wireless working at 2.4GHz/dual channel 40MHz/300Mb/s and the switch at Gigabit I would be happy enough. I don't think that will happen though, and will keep using the MR3420.
Thanks anyway.
Thanks anyway.