Trying to use client+AP mode to amplify the signal of an existing WIFI. The new WIFI can be connected, but no Internet.
I've verified that the existing WIFI has Internet connection. I'm running 1.12.0.
See attached configurations. Any suggestions? Thanks.
TL-WR1043N/ND v3 client+AP no internet
Moderator: Moderators
Re: TL-WR1043N/ND v3 client+AP no internet
Please host your config externally and link to them here
http://lantisproject.com/downloads/gargoyle_ispyisail.php for the latest releases
Please be respectful when posting. I do this in my free time on a volunteer basis.
Please be respectful when posting. I do this in my free time on a volunteer basis.
Re: TL-WR1043N/ND v3 client+AP no internet
Configurations below. I should mention that this setup works very intermittently. I'd say about 10% of the time I have Internet, but 90% of the time no Internet.
https://ibb.co/VW6Wz88
https://ibb.co/c6dRj8j
https://ibb.co/16wQf5Z
https://ibb.co/VW6Wz88
https://ibb.co/c6dRj8j
https://ibb.co/16wQf5Z
Re: TL-WR1043N/ND v3 client+AP no internet
Your WAN and LAN segments can't be in the same subnet when using this mode.
If you move Gargoyle to say 192.168.0.1, everything should start working.
If you move Gargoyle to say 192.168.0.1, everything should start working.
http://lantisproject.com/downloads/gargoyle_ispyisail.php for the latest releases
Please be respectful when posting. I do this in my free time on a volunteer basis.
Please be respectful when posting. I do this in my free time on a volunteer basis.
Re: TL-WR1043N/ND v3 client+AP no internet
Confirm your wireless settings again, making sure the password of the network is still correct.
http://lantisproject.com/downloads/gargoyle_ispyisail.php for the latest releases
Please be respectful when posting. I do this in my free time on a volunteer basis.
Please be respectful when posting. I do this in my free time on a volunteer basis.
Re: TL-WR1043N/ND v3 client+AP no internet
I have a similar setup with no issues. I have a relatively huge house. My system: AP {Archer C7 V5, running 1.11.0); 3 clients as wireless bridge/repeater placed strategically throughout the house. The 3 clients are cheap TP-link routers or clones {TL-WR1043ND ver 1.8 & Rosewill rnx-n300rt; all 3 running 1.10.0}.
The bridge Ip for the 3 clients are = 192.168.10.1 {different subnet} with non overlapped channel 1, 6 or 11 for clients. Stats: 5 ghz averages over 100 Mbps I love this cheap refurbished Archer C7 V5 courtesy of Amazon running Gargoyle 1.11.0; the clients, 2.4 ghz, are a little slow = averages 18 Mbps. This is acceptable since I only use it for connecting smart appliances, e.g., my smart water heater. Make sure bridge subnet is different and use non-overlapping channels. I hope this helps.
The bridge Ip for the 3 clients are = 192.168.10.1 {different subnet} with non overlapped channel 1, 6 or 11 for clients. Stats: 5 ghz averages over 100 Mbps I love this cheap refurbished Archer C7 V5 courtesy of Amazon running Gargoyle 1.11.0; the clients, 2.4 ghz, are a little slow = averages 18 Mbps. This is acceptable since I only use it for connecting smart appliances, e.g., my smart water heater. Make sure bridge subnet is different and use non-overlapping channels. I hope this helps.