You can set your own country code in 1.9.0 anyway.
I think you are programmers and not just Openwrt-copy/pasters with a new graphycal interface, tracking webmon and no ipv6 .
You can do a new plugin in the plugin-list. Can you create this plugin !?
I'm not sure you understand.
No plugin required. It is FULLY SUPPORTED.
https://lantisproject.com/downloads/gargoylebuilds for the latest releases
Please be respectful when posting. I do this in my free time on a volunteer basis.
https://lantisproject.com/downloads/gargoylebuilds for the latest releases
Please be respectful when posting. I do this in my free time on a volunteer basis.
Thank you Developers. I can only imagine the time and effort it takes to make Gargoyle.
I have found 1.8.1 to work well on both TL-WA850REv1 and TL-WR841Nv9 as as Wireless Bridge/Repeater. With 1.9.0 I am able to configure and ssh in but devices that connect to wlan0-1 will not receive an address (from gateway). /tmp/client_bridge/wlan0 is not created and the ebtable rules are not in the chains (20-client_bridge).
Hi guys,
I have a Netgear WNR2000v3 router, and I have tested 1.8 and 1.9 gargoyle. The factory update does not work, so I tried flash in the factory firmware, but the gargoyle admin page did neither load, not respond. DHCP did not work. So I tried flash with TFTP gargoyle img and bin but it did not work neither.
Then I tried flash openwrt sysupgrade bin with TFTP. Luci does load and I could flash gargoyle 1.9 bin.
Also, gargoyle admin page has been loaded and it works, however there seems to be a bug: if I switch off the router, it is resetting and all settings change to default.
https://lantisproject.com/downloads/gargoylebuilds for the latest releases
Please be respectful when posting. I do this in my free time on a volunteer basis.
After attaching a 1 TB Seagate USB 2.0 Drive to my TL-WR1043ND v2.1 running Gargoyle V1.9.0 Firmware and Formatting the External Unit as an EXT4 Data ONLY Drive (no Swap), I had an "Issue" creating Folders within the Shared Directory:
Initially from both Windows 8.1 and 10 creating a Folder was NOT possible (CIFS): Error Message was that Operation was "Restricted". Although with a FTP Client (Filezilla), creating Folders and Transferring was possible!!! After successful Folder Creation and File Transfer with the FTP Client, Folders could be created from Windows 8.1 (CIFS)???
Changed country DFS regulations (iw reg) to GY,BO,BZ,NZ,VE... then "saved changes" in "connection" - and channel 13 appeared in Gargoyle menu... Switched from 11 to 13 and saved changes in "connection" again, all working. After a router reboot i lost the (new) channels 12 and 13 - menu returned to 1-11 and "country US: DFS-FCC". Wifi down till saved back connection to channel 11.
Make it simple guys !!!
Just show in plugins.sh a new one called: "Enable channel 13"
Just show in plugins.sh a new one called: "Enable channel 13"
Just show in plugins.sh a new one called: "Enable channel 13"
Changed country DFS regulations (iw reg) to GY,BO,BZ,NZ,VE... then "saved changes" in "connection" - and channel 13 appeared in Gargoyle menu... Switched from 11 to 13 and saved changes in "connection" again, all working. After a router reboot i lost the (new) channels 12 and 13 - menu returned to 1-11 and "country US: DFS-FCC". Wifi down till saved back connection to channel 11.
Make it simple guys !!!
Just show in plugins.sh a new one called: "Enable channel 13"
Just show in plugins.sh a new one called: "Enable channel 13"
Just show in plugins.sh a new one called: "Enable channel 13"
It is simple.
uci set wireless.radio0.country=GY (or whatever you want).
uci set wireless.radio1.country=GY (if you have a dual band router)
uci commit wireless
Then reboot the router.
https://lantisproject.com/downloads/gargoylebuilds for the latest releases
Please be respectful when posting. I do this in my free time on a volunteer basis.
