Gargoyle 1.15.x BETA - 2024-10-14 - Based on OpenWrt 23.05

Want to share your OpenWrt / Gargoyle knowledge? Implemented a new feature? Let us know here.

Moderator: Moderators

Lantis
Moderator
Posts: 6921
Joined: Mon Jan 05, 2015 5:33 am
Location: Australia

Re: Gargoyle 1.15.x BETA - 2024-08-11 - Based on OpenWrt 23.05

Post by Lantis »

Lantis wrote:
Mon Sep 02, 2024 7:33 pm
Try
gpkg remove kmod-mwifiex-sdio
gpkg remove mwifiex-sdio-firmware

Remove any reference to radio2 from /etc/config/wireless
Reboot


Yes in my efforts to combine those two profiles the mwifiex driver got brought back in which is pretty much useless and causes more problems than it solves.
I uploaded a fresh mvebu directory under the same date which should not have this issue. Would love to hear feedback.
Thanks
https://lantisproject.com/downloads/gargoylebuilds for the latest releases
Please be respectful when posting. I do this in my free time on a volunteer basis.

angus
Posts: 36
Joined: Mon Apr 04, 2022 9:24 am

Re: Gargoyle 1.15.x BETA - 2024-08-11 - Based on OpenWrt 23.05

Post by angus »

Thanks Lantis. I'm running latest mvebu build. It looks good. There is one thing worth mentioning.
After configuring everything needed and enabling Force Clients To Use Router DNS Servers finally, I did a reboot. WRT3200ACM fell into a reboot cycle since then. I had to perform a hard factory reset to configure router again.
This time I chose not to force clients to use router DNS servers. Reboot cycle was not seen. It is weird. Will test again.

fifonik
Posts: 162
Joined: Fri Dec 02, 2016 3:52 am
Location: Brisbane, AU

Re: Gargoyle 1.15.x BETA - 2024-08-11 - Based on OpenWrt 23.05

Post by fifonik »

Since I've change my router from WRT1200 (Gargoyle 1.13) to GL-ET6000 (this Gargoyle 1.15.x) I'm having one strange issue:
I have a few PCs that connected to main router (wired connection) and a number of wireless devices. I'm whitelisting MAC addresses.
WiFi is configured without clients isolation.
All devices getting IP from DHCP (I'm forcing clients to use router custom DNS servers).
All these devices can connect to each other and to internet.
I also have WiFi extender in garage that is connecting to main router over WiFi (NOT guest network) and 3D printer connected to LAN port of the extender.
I can connect to printer from my PC (http, SSH) and from the printer to any device in my local network (I can SSH to the linux on printer from my PC and ping router or any local device from the printer).
However, the printer does not have internet access.
There is no any restrictions for the WiFi extender's or printer's MAC addresses.

Before I've replaced the router everything was working fine (printer had internet connection) and no any configuration changes were made on the WiFi extender or the printer).

UPDATE:
Unticking "Enforce DHCP assignments" helps.
However, what should I do to make it work when the option is ticked?
Thanks.

Lantis
Moderator
Posts: 6921
Joined: Mon Jan 05, 2015 5:33 am
Location: Australia

Re: Gargoyle 1.15.x BETA - 2024-08-11 - Based on OpenWrt 23.05

Post by Lantis »

It depends how the extender works. If it operates in WDS mode everything should work ok. Otherwise my understanding is that it is impossible.
https://lantisproject.com/downloads/gargoylebuilds for the latest releases
Please be respectful when posting. I do this in my free time on a volunteer basis.

User avatar
oliver44
Posts: 75
Joined: Tue Mar 20, 2018 1:29 am
Location: Romanaia

Re: Gargoyle 1.15.x BETA - 2024-08-11 - Based on OpenWrt 23.05

Post by oliver44 »

First of all, congratulations for the work done, the GL-MT6000 moves very well with Gargoyle, the latest version proposed by you!
Last edited by oliver44 on Wed Sep 11, 2024 5:46 pm, edited 1 time in total.
wdr3600 rev1.4 OpenWrt
wrt1900ACS v.2 OpenWrt/DD-WRT
GL-MT6000 OpenWrt/Gargoyle

User avatar
oliver44
Posts: 75
Joined: Tue Mar 20, 2018 1:29 am
Location: Romanaia

Re: Gargoyle 1.15.x BETA - 2024-03-11 - Based on OpenWrt 23.05

Post by oliver44 »

fifonik wrote:
Thu Jun 13, 2024 5:04 pm
oliver44 wrote:
Thu Mar 14, 2024 3:45 am
I would like to install some plugins that I also used on wrt1900acs v2 but I don't know what the command is for GL-MT6000, for wrt1900acs v2 I use
Can you compare performance of your MT6000 with wrt1900acs please? Thanks.
I am currently renovating the apartment, wrt1900acs v2 has not been connected for a long time, after I finish the renovation I will check the latest updates!

https://patchwork.ozlabs.org/project/op ... @jbsky.fr/

https://forum.openwrt.org/t/divested-wr ... 80522/1508
wdr3600 rev1.4 OpenWrt
wrt1900ACS v.2 OpenWrt/DD-WRT
GL-MT6000 OpenWrt/Gargoyle

angus
Posts: 36
Joined: Mon Apr 04, 2022 9:24 am

Re: Gargoyle 1.15.x BETA - 2024-08-11 - Based on OpenWrt 23.05

Post by angus »

angus wrote:
Tue Sep 03, 2024 11:50 pm
After configuring everything needed and enabling Force Clients To Use Router DNS Servers finally, I did a reboot. WRT3200ACM fell into a reboot cycle since then. I had to perform a hard factory reset to configure router again.
This time I chose not to force clients to use router DNS servers. Reboot cycle was not seen. It is weird. Will test again.
Hi Lantis,
Cannot replicate the issue anymore. This firmware revision works. Thanks.

arturjacek1
Posts: 1
Joined: Fri Oct 11, 2024 1:21 pm

Re: Gargoyle 1.15.x BETA - 2024-08-11 - Based on OpenWrt 23.05

Post by arturjacek1 »

Hi. Please tell me if there is a chance to get a beta image for the ZTE MF286D router? On the EKO-ONE forum Cezary for Gargoyle 1.14 made a system image for this router.
I respect very much that you do it in your free time and out of passion.Greetings from Polish.

Lantis
Moderator
Posts: 6921
Joined: Mon Jan 05, 2015 5:33 am
Location: Australia

Re: Gargoyle 1.15.x BETA - 2024-08-11 - Based on OpenWrt 23.05

Post by Lantis »

I will take a look
https://lantisproject.com/downloads/gargoylebuilds for the latest releases
Please be respectful when posting. I do this in my free time on a volunteer basis.

Lantis
Moderator
Posts: 6921
Joined: Mon Jan 05, 2015 5:33 am
Location: Australia

Re: Gargoyle 1.15.x BETA - 2024-08-11 - Based on OpenWrt 23.05

Post by Lantis »

arturjacek1 wrote:
Fri Oct 11, 2024 1:31 pm
Hi. Please tell me if there is a chance to get a beta image for the ZTE MF286D router? On the EKO-ONE forum Cezary for Gargoyle 1.14 made a system image for this router.
I respect very much that you do it in your free time and out of passion.Greetings from Polish.
https://lantisproject.com/downloads/gar ... JwbCI6MTB9
https://lantisproject.com/downloads/gargoylebuilds for the latest releases
Please be respectful when posting. I do this in my free time on a volunteer basis.

Post Reply