Adblock Plugin

[lollapalooza]

That's too bad
I have my Samsung TV that shows banners on the screen (which are blocked by Gargolye), and I'm trying to understand where it takes those banners from.

[morglum]

Hey everyone,
thanks for the firmware, and the adblock plugin.
I have installed it
(system - plugins - refresh plugins, then install "dns adblock for gargoyle"),
and enabled it (firewall - adblock - "enable adblock")

I'd like to add samsung tv ads addresses (https://gist.github.com/peteryates/b44b ... d4bcef1e52) , but can't find where the blacklist is.

thanks

[Lantis]

Because the list you're looking to add is relatively small (10-15 addresses ) you can just add them manually in the GUI to the blacklist. This will automatically include them with all other ad sites it loads during regular operation.

There's only 3 sections in the GUI, block, black and white. Hopefully that clarifies.

[doug_porsche]

I am being needed.

Is there a version of adblock for 1.13?
I just loaded the latest 1.13.0 on my wndr3700V4 and now am ready to install the adblock plugin.

I tried http://lantisproject.com/gargoyle_1.13.x/x86/x64
and no go.

[Lantis]

https://lantisproject.com/gargoyle_cust ... x/x86/x64/
This is the latest 1.13.x with ipv6 support, so your mileage may vary if that is not the build you're running.

[lollapalooza]

I'm currently using a consolidated hosts file from StevenBlack.
If you want to try it out, make sure your router has enough free space, because the hosts file itself consumes ~1.5MB alone.

Mt router has about 60 MB of free RAM, and about 29 MB of free space in /tmp, so I decided to give that a try.
I've added the StevenBlack file to the /plugin_root/usr/lib/adblock/runadblock.sh file, but when I run the script, I get following error:

Code: Select all

sort: out of memory

[lollapalooza]

USE --no-check-certificate !!!!

Today I installed V1.12 from scratch and, with my big surprise, the AdBlock plugin didn't work.

In the "Block List" I saw that there were no entries, so I decided to look into the runadblock.sh file.

At this point I found two issues:

• The link for 1st source does not work - Error 404
  This link is broken:

  Code: Select all

  https://www.mvps.org/winhelp2002/hosts.txt

  New link is the following:

  Code: Select all

  https://winhelp2002.mvps.org/hosts.txt

• The 2nd source is HTTP, while the website automatically switches to HTTPS.

Thanks to your suggestion, I fixed the script

[lollapalooza]

https://lantisproject.com/gargoyle_cust ... x/x86/x64/
This is the latest 1.13.x with ipv6 support, so your mileage may vary if that is not the build you're running.

I suppose that plugin-gargoyle-adblock_20191111-1.2.1_all.ipk will not work on Gargoyle 1.12.

Am I correct?

P.S. for you...
As per my previous post, it might be worth replacing the broken MVPS link to hosts file with the working one:

Code: Select all

https://winhelp2002.mvps.org/hosts.txt

[Lantis]

It should work, it doesn't have any major dependencies.
That link was updated in November 2019 lol. If its not working for you its because you're using an old version.

[lollapalooza]

That link was updated in November 2019 lol. If its not working for you its because you're using an old version.

It's the official 1.12 downloaded from here:
https://www.gargoyle-router.com/downloa ... pgrade.bin