The password did not get overwritten it is correct.
Yes ap to client gargoyle to router to lan pc
ubnt bullet m2
Moderator: Moderators
Re: ubnt bullet m2
Gateway mode
Connect via dhcp wireless
No current ip
Lan
Router ip 192.168.1.100
DNS default servers by ISP
Wireless
Client
2.4 operation bgn
Channel width 20mhz
Transmit power max
Mac filter disabled
Ssid to join correct ssid
Channel 6
Encryption wpa2 psk
Password set right
The channel and encryption is set automatically when I choose the ssid
Connect via dhcp wireless
No current ip
Lan
Router ip 192.168.1.100
DNS default servers by ISP
Wireless
Client
2.4 operation bgn
Channel width 20mhz
Transmit power max
Mac filter disabled
Ssid to join correct ssid
Channel 6
Encryption wpa2 psk
Password set right
The channel and encryption is set automatically when I choose the ssid
Re: ubnt bullet m2
It will probably be MAC address UBNT M2 (AP will reject defautl MAC). You must enter your own MAC that you have enabled on the AP side.
Turris Omnia with OpenWrt 21.02 - Tested
Linksys WRT3200ACM with Gargoyle 1.13.x
TL-WR1043ND v2 with Gargoyle 1.10.0
http://gargoyle.romanhk.cz custom builds by gargoyle users
Linksys WRT3200ACM with Gargoyle 1.13.x
TL-WR1043ND v2 with Gargoyle 1.10.0
http://gargoyle.romanhk.cz custom builds by gargoyle users
Re: ubnt bullet m2
The access point I connect to is a phone running a hotspot the mac address has never stopped me from connecting with the Airos firmware
Re: ubnt bullet m2
1. Go to the hotspot setting and clear the enabled devices here, then ask for UBNT to re-pair (the hotspot remembers the original AirOS connection - it must be deleted).
2. The number of clients is also set in the hotspot, try increasing the value.
2. The number of clients is also set in the hotspot, try increasing the value.
Turris Omnia with OpenWrt 21.02 - Tested
Linksys WRT3200ACM with Gargoyle 1.13.x
TL-WR1043ND v2 with Gargoyle 1.10.0
http://gargoyle.romanhk.cz custom builds by gargoyle users
Linksys WRT3200ACM with Gargoyle 1.13.x
TL-WR1043ND v2 with Gargoyle 1.10.0
http://gargoyle.romanhk.cz custom builds by gargoyle users
Re: ubnt bullet m2
You know what never mind. It's easier to buy a new one that no one installed this firmware on.
Re: ubnt bullet m2
The problem is/was you were a bit vaguemalkamus wrote:You know what never mind. It's easier to buy a new one that no one installed this firmware on.
That's why we needed screen shots to fill in the blanks.
Re: ubnt bullet m2
Gateway mode
Connect via dhcp wireless
No current ip
Lan
Router ip 192.168.1.100
DNS default servers by ISP
Wireless
Client
2.4 operation bgn
Channel width 20mhz
Transmit power max
Mac filter disabled
Ssid to join correct ssid
Channel 6
Encryption wpa2 psk
Password set right
The channel and encryption is set automatically when I choose the ssid
Those are all the settings that would have been in the screenshot.
A hotspot does not care what the mac address is that connects to it. You connect to it disconnect from it log in with a different piece of hardware. Change your mac address to whatever you want the hotspot does not know or care.
Connect via dhcp wireless
No current ip
Lan
Router ip 192.168.1.100
DNS default servers by ISP
Wireless
Client
2.4 operation bgn
Channel width 20mhz
Transmit power max
Mac filter disabled
Ssid to join correct ssid
Channel 6
Encryption wpa2 psk
Password set right
The channel and encryption is set automatically when I choose the ssid
Those are all the settings that would have been in the screenshot.
A hotspot does not care what the mac address is that connects to it. You connect to it disconnect from it log in with a different piece of hardware. Change your mac address to whatever you want the hotspot does not know or care.
Re: ubnt bullet m2
need these screen shots
also did you upgrade Gargoyle?
say "any version" to 1.11.0?
If so was preserve setting enabled?
also did you upgrade Gargoyle?
say "any version" to 1.11.0?
If so was preserve setting enabled?
Re: ubnt bullet m2
I don't even have any of those screens.
I honestly don't even want this on my bullet but it was on there already and it won't let me flash the OEM firmware. It is of no use to me.
As for upgrade it came to me with no memory of the password on it. I flashed it to the bullet 1.11 and 1.3 factory not upgrade with no saved settings.
Which brings up another issue. There is 2 firmwares for these, how can you make one to cover all the bullets?
I honestly don't even want this on my bullet but it was on there already and it won't let me flash the OEM firmware. It is of no use to me.
As for upgrade it came to me with no memory of the password on it. I flashed it to the bullet 1.11 and 1.3 factory not upgrade with no saved settings.
Which brings up another issue. There is 2 firmwares for these, how can you make one to cover all the bullets?