Problem after update 1.8->1.10 WDS systems
Moderator: Moderators
Problem after update 1.8->1.10 WDS systems
Hi!
I have a TP-Link TL-WR841N v8 (connected to Internet, set up as a Gateway and AP+WDS) and a TP-Link TL-WR841N v5 configured as WDS repeater.
It was working ok with 1.8. I've updated to 1.10 (clean) and reconfigured as was earlier. Now the repeater gets disconnected. I don't know how to troubleshoot it because there's no error message in the GUI.
What can I do?
Regards,
FSO
I have a TP-Link TL-WR841N v8 (connected to Internet, set up as a Gateway and AP+WDS) and a TP-Link TL-WR841N v5 configured as WDS repeater.
It was working ok with 1.8. I've updated to 1.10 (clean) and reconfigured as was earlier. Now the repeater gets disconnected. I don't know how to troubleshoot it because there's no error message in the GUI.
What can I do?
Regards,
FSO
Re: Problem after update 1.8->1.10 WDS systems
Can you please post both configs here to check?
http://lantisproject.com/downloads/gargoyle_ispyisail.php for the latest releases
Please be respectful when posting. I do this in my free time on a volunteer basis.
Please be respectful when posting. I do this in my free time on a volunteer basis.
Re: Problem after update 1.8->1.10 WDS systems
Can you point me a tutorial how to grab them? I'm not a newbie but didn't find a simple way, except screenshots.
Re: Problem after update 1.8->1.10 WDS systems
Make sure you follow these instructions when setting up a wireless bridge/repeater on Gargoyle >1.9.2. Bridge IP required config setting has changed.
Last edited by d3fz on Sat Jan 13, 2018 9:03 am, edited 1 time in total.
TP-Link Archer C7 v2 - Gargoyle 1.12.X
TP-Link WR842ND v2 - Gargoyle 1.10.X
TP-Link RE450 AC v2 - Stock FW 1.0.4
TP-Link WA850RE v1.2 - LEDE 17.01.1
TP-Link WR842ND v2 - Gargoyle 1.10.X
TP-Link RE450 AC v2 - Stock FW 1.0.4
TP-Link WA850RE v1.2 - LEDE 17.01.1
Re: Problem after update 1.8->1.10 WDS systems
But I'm using WDS!d3fz wrote:Make sure you follow these instructions when setting up a wireless bridge/repeater on Gargoyle >1.9.2. Bridge IP config has changed.
Re: Problem after update 1.8->1.10 WDS systems
Just some screenshots would be fine as long as they capture everything.
Then upload them elsewhere and link here
Then upload them elsewhere and link here
http://lantisproject.com/downloads/gargoyle_ispyisail.php for the latest releases
Please be respectful when posting. I do this in my free time on a volunteer basis.
Please be respectful when posting. I do this in my free time on a volunteer basis.
Re: Problem after update 1.8->1.10 WDS systems
Master:
Repeater:
This is my config right now. It's the same config that I had on 1.8.0.
Another thing I've noticed is that sometimes if I restart the repeater when it's not connected, it won't connect to the SSID of the master. But If I hit on Scan and select the same SSID, it reconnects.
Repeater:
This is my config right now. It's the same config that I had on 1.8.0.
Another thing I've noticed is that sometimes if I restart the repeater when it's not connected, it won't connect to the SSID of the master. But If I hit on Scan and select the same SSID, it reconnects.
Re: Problem after update 1.8->1.10 WDS systems
I understand that between your old version 1.8 and 1.9.2.x there is a fundamental config change requiring your Bridge/Repeater to be on a different subnet (even with WDS...).
Re: Problem after update 1.8->1.10 WDS systems
I don't think this is the case for WDS. I'm checking it out
http://lantisproject.com/downloads/gargoyle_ispyisail.php for the latest releases
Please be respectful when posting. I do this in my free time on a volunteer basis.
Please be respectful when posting. I do this in my free time on a volunteer basis.
Re: Problem after update 1.8->1.10 WDS systems
I've tried in Client Bridge instead of WDS but it didn't work.
Strange thing is that Windows said I was connected, but I couldn't get to the Internet, only could go to the master IP.
So I've reseted the configuration and started again, and now it's working, but in Client Bridge mode.
Now I don't know how can I get to the config page of the repeater to set it as WDS. Do I have to "clean reset" it?
Strange thing is that Windows said I was connected, but I couldn't get to the Internet, only could go to the master IP.
So I've reseted the configuration and started again, and now it's working, but in Client Bridge mode.
Now I don't know how can I get to the config page of the repeater to set it as WDS. Do I have to "clean reset" it?