gargoyle-ispy 2016-January-25 18:46.torrent

Want to share your OpenWrt / Gargoyle knowledge? Implemented a new feature? Let us know here.

Moderator: Moderators

dieselz
Posts: 41
Joined: Fri Jun 07, 2013 3:39 am
Location: Dubai, UAE
Contact:

Re: gargoyle-ispy 2016-January-25 18:46.torrent

Post by dieselz »

Thank you.[/quote]

Hi there open the webinterface go to system then Backup / Restore and Restore Default Configuration.[/quote]

Hi Tapper,

I tried that more than once this router and the TP-Link.
It doesnt seem to work with any firmware apart from the official one i dont know why.
I am so desperate to clear the NVRAM as it always refreshes the router.
Any ideas?
Or a way to reboot router into recovery mode VIA CLI?

Thank you.
Linksys WRT1900ACS V2 1.12.x gargoyle-iSpy

tapper
Moderator
Posts: 1076
Joined: Sun Oct 13, 2013 5:49 pm
Location: Stoke-on-trent UK

Re: gargoyle-ispy 2016-January-25 18:46.torrent

Post by tapper »

dieselz wrote:Thank you.
Hi there open the webinterface go to system then Backup / Restore and Restore Default Configuration.[/quote]

Hi Tapper,

I tried that more than once this router and the TP-Link.
It doesnt seem to work with any firmware apart from the official one i dont know why.
I am so desperate to clear the NVRAM as it always refreshes the router.
Any ideas?
Or a way to reboot router into recovery mode VIA CLI?

Thank you.[/quote]

The other way to do it is to boot in to Failsafe.
https://wiki.openwrt.org/doc/howto/generic.failsafe
Then do a firstboot

special commands:

firstboot reset settings to factory defaults
mount_root mount root-partition with config files

after mount_root:

passwd change root's password
/etc/config directory with config files

Openwrt offers a generic failsafe mode, which can be launched during a few seconds early in the boot process. With WNDR3700 the correct moment is when the power LED changes from steady orange to blinking green. If you at that moment press any button (WPS, Wifi or reset) during the next two seconds, you enter the failsafe mode, in which you can access the console with telnet. Successful entrance to the failsafe mode is indicated by a rapidly blinking power LED.
WNDR3700 provides the failsafe waiting moment indication messages both to the serial console and to the network, just like described in the failsafe mode article.
Linksys WRT3200ACM
NETGEAR Nighthawk R7800
NETGEAR R6260

dieselz
Posts: 41
Joined: Fri Jun 07, 2013 3:39 am
Location: Dubai, UAE
Contact:

Re: gargoyle-ispy 2016-January-25 18:46.torrent

Post by dieselz »

i was able to reboot the device previously to failsafe before according to the LED however, the telnet connect was refused, that is why i was asking if there is a way of soft reboot into recovery so that i can clear that damned NVRAM T_T

i cannot even save anything from GUI anymore.

could it be because this is a nand?
Linksys WRT1900ACS V2 1.12.x gargoyle-iSpy

n8b
Posts: 70
Joined: Wed Sep 16, 2015 1:20 pm
Location: Denmark

Re: gargoyle-ispy 2016-January-25 18:46.torrent

Post by n8b »

Adri wrote:Some channels are shown as 'unavailable' now. :(
Maybe a radar signal was detected?

ba_0001
Posts: 14
Joined: Sat Nov 28, 2015 4:43 pm

Re: gargoyle-ispy 2016-January-25 18:46.torrent

Post by ba_0001 »

Hi you guys are really working hard keep it up for good work i like to share my experine it might help you guys
Tp link archer c7 5 ghz performance is slow network will transfer is really slow then stock firmware.
For ip bandwith we cant see all ips at same page same time we have to select one by one. Please make it like we can see all bandwith of all ips not by selecting one by one.
Iptv is most comman feature in routers now. Its not working in gargoyle. Thanks. Sorry for my bad english.


tapper
Moderator
Posts: 1076
Joined: Sun Oct 13, 2013 5:49 pm
Location: Stoke-on-trent UK

Re: gargoyle-ispy 2016-January-25 18:46.torrent

Post by tapper »

dieselz wrote:i was able to reboot the device previously to failsafe before according to the LED however, the telnet connect was refused, that is why i was asking if there is a way of soft reboot into recovery so that i can clear that damned NVRAM T_T

i cannot even save anything from GUI anymore.

could it be because this is a nand?
No mate dont think so. Did you set a static IP on your PC wen you tryed to telnet to the router? If not that's were you went rong. In safe moad there is no DHCP server running on the router so the computer will not no what IP to use so falls back to using a 69.xx IP.
Linksys WRT3200ACM
NETGEAR Nighthawk R7800
NETGEAR R6260

deanMKD
Posts: 18
Joined: Fri Apr 03, 2015 3:06 pm

Re: gargoyle-ispy 2016-January-25 18:46.torrent

Post by deanMKD »

Tested this build on my TP-Link MR3020 and WR703N and works great without issues for more then 6 days !!

P.S: Left this torrent to seed on my seedbox PC 24/7. :D

ispyisail
Moderator
Posts: 5194
Joined: Mon Apr 06, 2009 3:15 am
Location: New Zealand

Re: gargoyle-ispy 2016-January-25 18:46.torrent

Post by ispyisail »

P.S: Left this torrent to seed on my seedbox PC 24/7.
Thanks

Did you try and make a torrent uncompressed?

jd45321
Posts: 26
Joined: Tue Dec 01, 2015 5:08 pm

Re: gargoyle-ispy 2016-January-25 18:46.torrent

Post by jd45321 »

deanMKD wrote:Tested this build on my TP-Link MR3020 and WR703N and works great without issues for more then 6 days !!

P.S: Left this torrent to seed on my seedbox PC 24/7. :D
Does this mean we can download just the version for our router instead every file? If so, how do we do this?

Thanks

Post Reply