How to revert back to factory firmware
Moderator: Moderators
How to revert back to factory firmware
I running gargoyle 1.6.1 on wr941nd v3 without problem. But i want to revert back for some reason because i need to try other firmware. This is my normal habit. Can anyone guide me how to flash back to stock firmware without brick the router
Thank you
Thank you
Re: How to revert back to factory firmware
Here is another discussion.
If you need to cut a firmware i can do it for you.
http://www.gargoyle-router.com/phpbb/vi ... f=5&t=4816
If you need to cut a firmware i can do it for you.
http://www.gargoyle-router.com/phpbb/vi ... f=5&t=4816
Re: How to revert back to factory firmware
1-here you have 2 options http://www.gargoyle-router.com/phpbb/vi ... f=5&t=4816roman9441 wrote: 1-i want to revert back
2-This is my normal habit.
3-how to flash back to stock firmware without brick the router
2-bad habit
3-don't ask for warrantee here, every one that's on third party FW should have serial cable and be prepare for a brick.
Listen to omiez that's a good proposal
Re: How to revert back to factory firmware
Thx you for answer. I'm not ask for warranty :/ i just don't want to brick it
But thx for the answer but may be i guess better stick with gargoyle as you said it bad habit
Anyway Thank you all
Guess i should study about what you talking. The serial cable
Thx for advise
But thx for the answer but may be i guess better stick with gargoyle as you said it bad habit
Anyway Thank you all
Guess i should study about what you talking. The serial cable
Thx for advise
Re: How to revert back to factory firmware
Thank you danymarc for your answer.
I had a brick problem with my TL-WR841ND and had to wait a lot of time until my Nokia Cable arrived to unbrick.
Now that i know what i made wrong the best way to flash back is to cut the firmware upload it via WinScp and flash it with the mtd command.
I had a brick problem with my TL-WR841ND and had to wait a lot of time until my Nokia Cable arrived to unbrick.
Now that i know what i made wrong the best way to flash back is to cut the firmware upload it via WinScp and flash it with the mtd command.
Re: How to revert back to factory firmware
I running gargoyle 1.6.1 on tl-wdr4300
could anyone help me cut the version:TL-WDR4300_V1_130617.
filename: wdr4300v1_en_3_13_33_up_boot(130617).bin
i want to revert back for factory firmware. Can anyone guide me how to flash back to stock firmware without brick the router
Thank you
could anyone help me cut the version:TL-WDR4300_V1_130617.
filename: wdr4300v1_en_3_13_33_up_boot(130617).bin
i want to revert back for factory firmware. Can anyone guide me how to flash back to stock firmware without brick the router
Thank you
Re: How to revert back to factory firmware
Hello garyhome
Upload the file using Winscp in the /tmp folder of your router.
Connect with Putty and give this commands:
cd /tmp
mtd -r write /tmp/tplink.bin firmware
Every command at once hitting Enter.
Here is the link to the Cutted Firmware:
http://1drv.ms/1sedBjW
If it is not the last version just upgrade normally after flashing this one.
Upload the file using Winscp in the /tmp folder of your router.
Connect with Putty and give this commands:
cd /tmp
mtd -r write /tmp/tplink.bin firmware
Every command at once hitting Enter.
Here is the link to the Cutted Firmware:
http://1drv.ms/1sedBjW
If it is not the last version just upgrade normally after flashing this one.
Re: How to revert back to factory firmware
Omiez to let you know
I used your post to help kuruczfarm from DD-WRT forum and he was happy back to stock
interesting answer
I have a doubt, you uploaded a stripped FW with no boot, to be uploaded through WinScp
My question, what happens if he does it through web-ui, according to my logic it's the same, and it's clear to me that sometimes web-ui does not let you upload for whatever reason, as kuruczfarm case
I used your post to help kuruczfarm from DD-WRT forum and he was happy back to stock
interesting answer
here http://www.dd-wrt.com/phpBB2/viewtopic. ... 977#903977I did the same. mtd write error However it reverted to stock fw after reboot
I have a doubt, you uploaded a stripped FW with no boot, to be uploaded through WinScp
My question, what happens if he does it through web-ui, according to my logic it's the same, and it's clear to me that sometimes web-ui does not let you upload for whatever reason, as kuruczfarm case
Re: How to revert back to factory firmware
Look, i don't know if we can flash back via Web Interface but to be sure i did not try it and will allways use the upload method because it worked several times without problem.
In DDWRT they have revert firmwares it would be a nice option on Gargoyle if this was possible.
In DDWRT they have revert firmwares it would be a nice option on Gargoyle if this was possible.