TP-Link WR1043nd v1.10
Moderator: Moderators
TP-Link WR1043nd v1.10
Is TP-Link WR1043nd v1.10 version supported. I don't see it on supported list. If so, which is stable version to download and install. Do I need to install German version before going with Gargoyle firmware?
Re: TP-Link WR1043nd v1.10
http://wiki.openwrt.org/toh/tp-link/tl- ... d.versions
http://www.gargoyle-router.com/wiki/dok ... =changelog
Looks like 1.5.9 and 1.5.10 should work
As usual try at your own risk
http://www.gargoyle-router.com/wiki/dok ... =changelog
Looks like 1.5.9 and 1.5.10 should work
As usual try at your own risk
Re: TP-Link WR1043nd v1.10
Thanks ...will try & let you know how it goes.
Re: TP-Link WR1043nd v1.10
I'm running 1.5.10 on a 1043nd 1.11 so your 1.10 should be fine.
Re: TP-Link WR1043nd v1.10
Hello
Sorry if this question is old. Was reading some posts and a wiki some very old and some from just a few months back and seem to get conflicting information.
I have been running gargoyle on my wndr3700 v1 for well over a year with excellent results (thanks Eric) Just bought the in-laws a TP Link WR1043nd ver 1.11 and want to configure it and send it with the wife for x-mas. (they live 4 hours away and I have to work)
Can I load the one of these files directly from the TP firmware. I do know I may need to shorten filename, but not sure if I will have to revert to older stock firmware first.
gargoyle_1.5.11-ar71xx-generic-tl-wr1043nd-v1-squashfs-factory.bin
gargoyle_1.5.11-ar71xx-generic-tl-wr1043nd-v1-squashfs-sysupgrade.bin
Been a long time since I have upgraded from the site and forget which to use (If I can at all) Normally I would just go for it and report my results - just don't have time to figure it out on my own before she makes the trip, or time to get a new device in the mail.
Thanks for the help here & on all the other thousands of posts I've read over the years.
John
Sorry if this question is old. Was reading some posts and a wiki some very old and some from just a few months back and seem to get conflicting information.
I have been running gargoyle on my wndr3700 v1 for well over a year with excellent results (thanks Eric) Just bought the in-laws a TP Link WR1043nd ver 1.11 and want to configure it and send it with the wife for x-mas. (they live 4 hours away and I have to work)
Can I load the one of these files directly from the TP firmware. I do know I may need to shorten filename, but not sure if I will have to revert to older stock firmware first.
gargoyle_1.5.11-ar71xx-generic-tl-wr1043nd-v1-squashfs-factory.bin
gargoyle_1.5.11-ar71xx-generic-tl-wr1043nd-v1-squashfs-sysupgrade.bin
Been a long time since I have upgraded from the site and forget which to use (If I can at all) Normally I would just go for it and report my results - just don't have time to figure it out on my own before she makes the trip, or time to get a new device in the mail.
Thanks for the help here & on all the other thousands of posts I've read over the years.
John
Re: TP-Link WR1043nd v1.10
Hi if you are stil on stock fw then flash gargoyle_1.5.11-ar71xx-generic-tl-wr1043nd-v1-squashfs-factory.bin
if it has openwrt or ddwrt on there then go with the 2nd one. good luck!
if it has openwrt or ddwrt on there then go with the 2nd one. good luck!
Linksys WRT3200ACM
NETGEAR Nighthawk R7800
NETGEAR R6260
NETGEAR Nighthawk R7800
NETGEAR R6260
Re: TP-Link WR1043nd v1.10
Tapper
Thanks a lot for the quick reply. I will do that in the morning. I appreciate it.
Thanks a lot for the quick reply. I will do that in the morning. I appreciate it.