Version 1.5.9 - Plugins Interface
Moderator: Moderators
Re: Version 1.5.9 - Plugins Interface
When upgrading from 1.5.8 preserving settings file /etc/config/gargoyle is remaining old, and Plugins option not showing.
Re: Version 1.5.9 - Plugins Interface
Reporting in from successful 1.5.8 -> 1.5.9 upgrade on Linksys WRT160NL.
I did not "Attempt to Preserve Settings". Manual settings restore worked fine. I'll let you know in a few days if 1.5.8 version's wireless problems still exist.
Gargoyle plugin URL returns "403 Forbidden". I guess there are no plugins available yet.
Thank you for this great firmware!
I did not "Attempt to Preserve Settings". Manual settings restore worked fine. I'll let you know in a few days if 1.5.8 version's wireless problems still exist.
Gargoyle plugin URL returns "403 Forbidden". I guess there are no plugins available yet.
Thank you for this great firmware!
Re: Version 1.5.9 - Plugins Interface
WR4310ND - When trying to change password of a user under usb storage, i get a password mismatch between the two new passwords.
I've even tried to put "1" as a password, but i get the same message.
I use Chrome.
I've even tried to put "1" as a password, but i get the same message.
I use Chrome.
Re: Version 1.5.9 - Plugins Interface
I upgraded fine. Ticked the "Preserve Settings" box. However if I should have a menu item Systems\Plugins, then it's not there.Wild Rat wrote:When upgrading from 1.5.8 preserving settings file /etc/config/gargoyle is remaining old, and Plugins option not showing.
Suggestions other than a full "firstboot"'?
Re: Version 1.5.9 - Plugins Interface
Additionally to the above for my WNDR3700 v2:Sitman wrote:I upgraded fine. Ticked the "Preserve Settings" box. However if I should have a menu item Systems\Plugins, then it's not there.Wild Rat wrote:When upgrading from 1.5.8 preserving settings file /etc/config/gargoyle is remaining old, and Plugins option not showing.
Suggestions other than a full "firstboot"'?
I think something is dodgy with this release. (Sorry Eric)
Flashed 1.5.9 over ispyisail's last release and as I said ticked the "Preserve Settings" box.
I changed my DNS servers via the GUI. Then my internet / NIC dropped connection. The router appeared unresponsive. I changed my IP manually to 192.168.1.2 with GW 192.168.1.1 and still couldn't connect.
I then gained access via the reset / Telnet method. I ran 'firstboot' so the same as reset to default from the GUI. Recycled the power and was able to connect to the router via the browser GUI. The menu item Systems\Plugins was then available. I ran a refresh and got a few themes listed.
Then I changed my settings for wireless, static IPs etc and saved the config. A few times whilst trying to save the config I was sent back to the password screen to reenter it. This is after about 2 or 3 mins of being in say the Static IP section.
I then rebooted the router and it didn't come backup. It just sat with the green power light blinking and the WAN and the 1 connected LAN for hard amber.
Once again I entered the Telnet reset and carried out a firstboot. Recycled the power / router and it didn't come up even after 15 minutes. Just the same green power light blinking and the WAN and the 1 connected LAN for hard amber.
I've now done another telnet reset firstboot and powered off the router. So I'm sending this plugged directly into my cable modem.
What can I do? I'd even think of dropping back to 1.5.6 if you thought that was more stable.
Re: Version 1.5.9 - Plugins Interface
Eric, Is there any guide available for how one would write a Gargoyle plugin?
Re: Version 1.5.9 - Plugins Interface
Hello,
I can confirm (with both a WNDR3700v1 and a WNDR3800) that "Plugins" does not show up under "System" if you keep your settings while upgrading from 1.5.8 to 1.5.9. However, the url <router-ip>/plugins.sh works fine.
The issue does not exist if you upgrade without preserving the settings, and then restore your configuration.
It appears that a reflash is not necessary to fix this issue. You can save your configuration, restore the default configuration, and then restore the saved configuration. "Plugins" will then show up under "System".
Good news: the wireless issues experienced under 1.5.8 with a WNDR3700v1 and a WNDR3800 have disappeared with 1.5.9. These issues were apparently fixed in OpenWRT around r34200. Details in https://dev.openwrt.org/ticket/11894
Thanks for the great work, Eric.
Cheers!
I can confirm (with both a WNDR3700v1 and a WNDR3800) that "Plugins" does not show up under "System" if you keep your settings while upgrading from 1.5.8 to 1.5.9. However, the url <router-ip>/plugins.sh works fine.
The issue does not exist if you upgrade without preserving the settings, and then restore your configuration.
It appears that a reflash is not necessary to fix this issue. You can save your configuration, restore the default configuration, and then restore the saved configuration. "Plugins" will then show up under "System".
Good news: the wireless issues experienced under 1.5.8 with a WNDR3700v1 and a WNDR3800 have disappeared with 1.5.9. These issues were apparently fixed in OpenWRT around r34200. Details in https://dev.openwrt.org/ticket/11894
Thanks for the great work, Eric.
Cheers!
Re: Version 1.5.9 - Plugins Interface
same here
from 1.5.7 to 1.5.9 preserve setting not working
after clean installation it is ok
from 1.5.7 to 1.5.9 preserve setting not working
after clean installation it is ok
- SirLancelot1982
- Posts: 20
- Joined: Wed Feb 08, 2012 4:01 pm
Re: Version 1.5.9 - Plugins Interface
Just install Gargoyle 1.5.9 on my TP-LINK TL-WR1043ND HW:1.9
Everything looks quick and stable. Even my Epson Stylus DX7450 started to print wireless(on Windows 7 32-bit and Ubuntu 12.04).
Everything looks quick and stable. Even my Epson Stylus DX7450 started to print wireless(on Windows 7 32-bit and Ubuntu 12.04).
---
Best Regards
SirLancelot1982
#---#
ROUTER: TP-LINK TL-WR1043ND
HW: 1.8
SW: Gargoyle 1.5.8
#---#
Best Regards
SirLancelot1982
#---#
ROUTER: TP-LINK TL-WR1043ND
HW: 1.8
SW: Gargoyle 1.5.8
#---#
Re: Version 1.5.9 - Plugins Interface
Hello guys!
Came across the Gargoyle firmware after trying dd-wrt on my netgear WNDR3700 and haven't looked back since. Really nice firmware and cheers for all the hard work put in.
I am currently running 1.5.5 and very stable too. I would like to upgrade to 1.5.9. Would it be possible for me to retain settings by making a backup off my settings, then upgrade to 1.5.9 without preserving settings, and after upgrading import the settings?
Thanks for any advice on this matter!
Came across the Gargoyle firmware after trying dd-wrt on my netgear WNDR3700 and haven't looked back since. Really nice firmware and cheers for all the hard work put in.
I am currently running 1.5.5 and very stable too. I would like to upgrade to 1.5.9. Would it be possible for me to retain settings by making a backup off my settings, then upgrade to 1.5.9 without preserving settings, and after upgrading import the settings?
Thanks for any advice on this matter!
---
using Gargoyle firmware 1.5.5 on a Netgear WNDR3700v2
---
using Gargoyle firmware 1.5.5 on a Netgear WNDR3700v2
---