Version 1.5.7 -- OpenWRT "Attitude Adjustment"

[b4nd0ler0]

Another one requesting feedback on 1.5.7 Attitude Adjustment running on a Netgear WNDR3700 v1.

I'm currently on 1.5.4, only using "basic wireless router" features
(no VPN, no USB, no QoS)

Has wireless performance improved over that of v1.5.4?
I often find the latter quite poor, particularly stability and range for both 2.4 and 5 GHz bands.

Thanks

[Silvah]

wtf is this openvpn gargoyle not supporting tap? I had to delete it and configure it from the console. I'm using tap bridge and this is really lame.

The Attitude Adjustment didn't work you say?

Apparently not for him

Running fine so far for me on 2x 1043nd, one flashed from factory and one from 1.5.6.

Running what? I was talking about openvpn in 1.5.7... Try to configure openvpn with gui with the dev tap option. It says that tap is not supported

edit ispy

[danielkza]

Another one requesting feedback on 1.5.7 Attitude Adjustment running on a Netgear WNDR3700 v1.

I'm currently on 1.5.4, only using "basic wireless router" features
(no VPN, no USB, no QoS)

Has wireless performance improved over that of v1.5.4?
I often find the latter quite poor, particularly stability and range for both 2.4 and 5 GHz bands.

Thanks

The WNDR3700v1 uses the Atheros 9k wireless chipset, which did receive quite a lot of work on Attitude Adjusment. I had very poor performance with my WR1043NDv1 and it improved substantially, in both stability and bandwidth. I'd give 1.5.7 a try if I were you.

[edud2k]

Hello fellaz,

I installed 1.5.7 on the TP LINK TL WR740N v4 and can not make the network wirelesse work, the machines see the network but can not authenticate the password, I am using LAN ports and how I enabled Wireless AP. any tips on how to solve this problem.

Edud2k

[wilsonhlacerda]

TP-LINK WDR4300 or WDR4310, have anyone tried? Hardware version 1.0, 1.1, 1.2...?
http://www.gargoyle-router.com/phpbb/vi ... f=7&t=3134
thanks!

[jefman]

Pls Build for x86 without 3dnow instructions. my x86 machine cannot boot it say my current system does not support 3dnow instructions and cannot continue.

Thanks Eric

[DoesItMatter]

TP-LINK WDR4300 or WDR4310, have anyone tried? Hardware version 1.0, 1.1, 1.2...?
http://www.gargoyle-router.com/phpbb/vi ... f=7&t=3134
thanks!

I replied in the post.

You can be the first!

Try it out and see how it works for you!

[dnd]

dare i ask, is there an eta for 1.5.8? this one sounds a little unstable for me at the moment.

[UsernameTaken]

Using a 1043ND v1.8 I've noticed that whenever I connect an openvpn client the router becomes unresponsive after a couple of minutes (the wifi goes down atleast, I didn't try with a wired connection to see if it was just the wifi or the whole router).

I've not tried openvpn in any previous version of gargoyle so I cannot tell if this is a new problem or not.

All setting were made from scratch in a fresh installation.

[Tonka]

I noticed a previous comment about 1.5.7 being unstable on a WNDR3800 however I can report no problems in my case - I've no TOR or QoS set up but I am using OpenVPN. Not sure if it was necessary, I did do a 30 30 30 reset before upgrading.