Russian PPPoE (Dual Access)
Moderator: Moderators
Russian PPPoE (Dual Access)
Good afternoon. Please implement this type of connectivity as Russia pppoe or dual access. This is when the wan port have 2 asssigned address by pppoe and local(maybe static and DHCP).
I have TP-LINK 1043, on stock firmware connection Russia PPPoE working very well, but the rest leaves much to be desired
Thanks in advance.
I have TP-LINK 1043, on stock firmware connection Russia PPPoE working very well, but the rest leaves much to be desired
Thanks in advance.
Re: Russian PPPoE (Dual Access)
Вы далекооо не первый , кто об этом просит
Не хотят этого делать буржуи . Хотя в той же wive-ng это реализовано прекрасно.
Не хотят этого делать буржуи . Хотя в той же wive-ng это реализовано прекрасно.
Re: Russian PPPoE (Dual Access)
I am afraid I cannot understand the technical details of this request. Please post more details about why Russian PPPoE is different than everyone elses PPPoE? Gargoyle already receives a DHCP assigned IP address on its WAN port if your PPPoE modem is configured to supply such addresses in addition to the PPPoE assigned address.
And counter what was stated by werter below I am not aware of any previous request for such a feature.
And counter what was stated by werter below I am not aware of any previous request for such a feature.
Linksys WRT1900ACv2
Netgear WNDR3700v2
TP Link 1043ND v3
TP-Link TL-WDR3600 v1
Buffalo WZR-HP-G300NH2
WRT54G-TM
Netgear WNDR3700v2
TP Link 1043ND v3
TP-Link TL-WDR3600 v1
Buffalo WZR-HP-G300NH2
WRT54G-TM
Re: Russian PPPoE (Dual Access)
pbix, i think they ask for PPTP Dual Access as i saw on their russian forums
TL-WR1043ND HW v1.8 | FW Gargoyle 1.5.X (Built 20120504-1907 git@2bf3cf2) | 2 Mbit | PPPoE
Re: Russian PPPoE (Dual Access)
Thank you very much for your feedback. I'll try to explain their connection.
ADSL modem in bridge mode, set up two PVC compounds - one for the Internet, the second for IP TV.
Connected to the router port WAN, which rises PPPOE connection to the Internet.
1) To set up IP-TV in the config file to specify IGMPPROXY upstate interface - what should I specify?
2) How to get to the ADSL modem - how?
Thank you for your attention.
Sorry for bad english
ADSL modem in bridge mode, set up two PVC compounds - one for the Internet, the second for IP TV.
Connected to the router port WAN, which rises PPPOE connection to the Internet.
1) To set up IP-TV in the config file to specify IGMPPROXY upstate interface - what should I specify?
2) How to get to the ADSL modem - how?
Thank you for your attention.
Sorry for bad english
Re: Russian PPPoE (Dual Access)
Here as implemented in Wive-ng firmare :
1. First WAN connection is STATIC or DHCP
2. Second is VPN connection - PPTP, L2TP or PPPOE
Can you make like this in Gargoyle ?
1. First WAN connection is STATIC or DHCP
2. Second is VPN connection - PPTP, L2TP or PPPOE
Can you make like this in Gargoyle ?
- Attachments
-
- VPN
- 3.jpg (151.4 KiB) Viewed 26435 times
-
- WAN
- 2.jpg (123.77 KiB) Viewed 26435 times
-
- The general form
- 1.jpg (34.22 KiB) Viewed 26435 times
Re: Russian PPPoE (Dual Access)
Yes, but there is only the possibility for DHCP and PPPoE (it is one setting "PPPoE client" that is the same as choosing PPPoE and DHCP).werter wrote:Here as implemented in Wive-ng firmare :
1. First WAN connection is STATIC or DHCP
2. Second is VPN connection - PPTP, L2TP or PPPOE
Can you make like this in Gargoyle ?
You should be able to use L2TP with this package:
http://wiki.openwrt.org/doc/howto/connect_by_l2tp
Router: TL-WR1043ND - Gargoyle 1.5.4
AP: TL-WR1043ND - Gargoyle 1.5.4
AP: TL-WR1043ND - Gargoyle 1.5.4
Re: Russian PPPoE (Dual Access)
Hmm..May be you don't understand me?hnl_dk wrote:Yes, but there is only the possibility for DHCP and PPPoE (it is one setting "PPPoE client" that is the same as choosing PPPoE and DHCP).werter wrote:Here as implemented in Wive-ng firmare :
1. First WAN connection is STATIC or DHCP
2. Second is VPN connection - PPTP, L2TP or PPPOE
Can you make like this in Gargoyle ?
You should be able to use L2TP with this package:
http://wiki.openwrt.org/doc/howto/connect_by_l2tp
I would like to be able to establish two connections simultaneously - first Static or DHCP and second - PPTP, L2TP or PPPOE
If it is possible to Wive-ng (Linux) and DD-WRT (Linux) why is not possible to Gargoyle (Linux) like on my screenshots?
Re: Russian PPPoE (Dual Access)
On the picture, it just looks like there is only one WAN connection, with PPPoE and a static IP address.werter wrote:Hmm..May be you don't understand me?hnl_dk wrote:Yes, but there is only the possibility for DHCP and PPPoE (it is one setting "PPPoE client" that is the same as choosing PPPoE and DHCP).werter wrote:Here as implemented in Wive-ng firmare :
1. First WAN connection is STATIC or DHCP
2. Second is VPN connection - PPTP, L2TP or PPPOE
Can you make like this in Gargoyle ?
You should be able to use L2TP with this package:
http://wiki.openwrt.org/doc/howto/connect_by_l2tp
I would like to be able to establish two connections simultaneously - first Static or DHCP and second - PPTP, L2TP or PPPOE
If it is possible to Wive-ng (Linux) and DD-WRT (Linux) why is not possible to Gargoyle (Linux) like on my screenshots?
So you are in fact having having two WAN ports?
If so, can we give that a try.
Router: TL-WR1043ND - Gargoyle 1.5.4
AP: TL-WR1043ND - Gargoyle 1.5.4
AP: TL-WR1043ND - Gargoyle 1.5.4
Re: Russian PPPoE (Dual Access)
Gargoyle cannot perform this function and there is no plan to add this type of feature.
Perhaps you can do this with OpenWRT with some effort if you are familiar with Linux networking. For more help on that you should post at openwrt.org.
Perhaps you can do this with OpenWRT with some effort if you are familiar with Linux networking. For more help on that you should post at openwrt.org.
Linksys WRT1900ACv2
Netgear WNDR3700v2
TP Link 1043ND v3
TP-Link TL-WDR3600 v1
Buffalo WZR-HP-G300NH2
WRT54G-TM
Netgear WNDR3700v2
TP Link 1043ND v3
TP-Link TL-WDR3600 v1
Buffalo WZR-HP-G300NH2
WRT54G-TM