Have you got igb driver?
"dmesg" just after booting to see what the kernel has to say about your hardware.
Looking to build a x86 base router with gargoyle
Moderator: Moderators
Re: Looking to build a x86 base router with gargoyle
http://lantisproject.com/downloads/gargoyle_ispyisail.php for the latest releases
Please be respectful when posting. I do this in my free time on a volunteer basis.
Please be respectful when posting. I do this in my free time on a volunteer basis.
Re: Looking to build a x86 base router with gargoyle
I did a dmesg | grep -i igb and I got nothing???
Re: Looking to build a x86 base router with gargoyle
but I see the e1000e and e1000 loading up
Re: Looking to build a x86 base router with gargoyle
I just found the igb module, recompiling...
Re: Looking to build a x86 base router with gargoyle
It work, both eth0 and eth1 are online... Now on to next problem, wireless...
Re: Looking to build a x86 base router with gargoyle
Cool. Progress at least 
As I said before o think that wireless device is covered by brcmsmac.
I'd start there
As I said before o think that wireless device is covered by brcmsmac.
I'd start there
http://lantisproject.com/downloads/gargoyle_ispyisail.php for the latest releases
Please be respectful when posting. I do this in my free time on a volunteer basis.
Please be respectful when posting. I do this in my free time on a volunteer basis.
Re: Looking to build a x86 base router with gargoyle
Ok stuck again, wireless seam to being detected properly:
I gargoyle, it on give B and G and 2.4 GHz for signal, and when I try to stop wireless in "wifi scheduler", first it's active and I can't stop it.
Code: Select all
[ 16.331099] bcma: bus0: Found chip with id 43224, rev 0x01 and package 0x0A
[ 16.352059] bcma: bus0: Core 0 found: ChipCommon (manuf 0x4BF, id 0x800, rev 0x22, class 0x0)
[ 16.377777] bcma: bus0: Core 1 found: IEEE 802.11 (manuf 0x4BF, id 0x812, rev 0x17, class 0x0)
[ 16.403770] bcma: bus0: Core 2 found: PCIe (manuf 0x4BF, id 0x820, rev 0x0F, class 0x0)
[ 16.477891] bcma: bus0: Bus registered
[ 18.607069] b43-phy0: Broadcom 43224 WLAN found (core revision 23)
[ 18.626091] b43-phy0: Found PHY: Analog 8, Type 4 (N), Revision 6
[ 18.644439] b43-phy0: Found Radio: Manuf 0x17F, ID 0x2056, Revision 11, Version 0
[ 18.667505] Broadcom 43xx driver loaded [ Features: PNL ]
[ 18.691583] Broadcom 43xx-legacy driver loaded [ Features: PLD ]
[ 18.710105] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
Re: Looking to build a x86 base router with gargoyle
Can you check for errors in the system log?
Have you got iwinfo compiled?
Have you got iwinfo compiled?
http://lantisproject.com/downloads/gargoyle_ispyisail.php for the latest releases
Please be respectful when posting. I do this in my free time on a volunteer basis.
Please be respectful when posting. I do this in my free time on a volunteer basis.
Re: Looking to build a x86 base router with gargoyle
iwinfo wasn't selected. Recompiling, once done, what will iwinfo give me?
Re: Looking to build a x86 base router with gargoyle
Here the logs after booting with the new img.
Code: Select all
[ 0.000000] Linux version 3.18.45 (root@phil-desktop) (gcc version 4.8.3 (OpenWrt/Linaro GCC 4.8-2014.04 r49389) ) #20 SMP Sun Mar 12 16:38:13 EDT 2017
[ 0.000000] Command line: BOOT_IMAGE=/boot/vmlinuz block2mtd.block2mtd=PARTUUID=c3d6313e-02,65536,rootfs,5 root=/dev/mtdblock0 rootfstype=squashfs rootwait console=tty0 console=ttyS0,38400n8 noinitrd
[ 0.000000] e820: BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: [mem 0x0000000000000000-0x000000000009d7ff] usable
[ 0.000000] BIOS-e820: [mem 0x000000000009d800-0x000000000009ffff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000000e0000-0x00000000000fffff] reserved
[ 0.000000] BIOS-e820: [mem 0x0000000000100000-0x00000000d6e13fff] usable
[ 0.000000] BIOS-e820: [mem 0x00000000d6e14000-0x00000000d70cafff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000d70cb000-0x00000000db359fff] usable
[ 0.000000] BIOS-e820: [mem 0x00000000db35a000-0x00000000db3b9fff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000db3ba000-0x00000000db5a9fff] usable
[ 0.000000] BIOS-e820: [mem 0x00000000db5aa000-0x00000000dbd26fff] ACPI NVS
[ 0.000000] BIOS-e820: [mem 0x00000000dbd27000-0x00000000dbffefff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000dbfff000-0x00000000dbffffff] usable
[ 0.000000] BIOS-e820: [mem 0x00000000dd000000-0x00000000df1fffff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000f8000000-0x00000000fbffffff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000fec00000-0x00000000fec00fff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000fed00000-0x00000000fed03fff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000fed1c000-0x00000000fed1ffff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000fee00000-0x00000000fee00fff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000ff000000-0x00000000ffffffff] reserved
[ 0.000000] BIOS-e820: [mem 0x0000000100000000-0x000000011fdfffff] usable
[ 0.000000] NX (Execute Disable) protection: active
[ 0.000000] e820: update [mem 0x00000000-0x00000fff] usable ==> reserved
[ 0.000000] e820: remove [mem 0x000a0000-0x000fffff] usable
[ 0.000000] AGP: No AGP bridge found
[ 0.000000] e820: last_pfn = 0x11fe00 max_arch_pfn = 0x400000000
[ 0.000000] MTRR default type: uncachable
[ 0.000000] MTRR fixed ranges enabled:
[ 0.000000] 00000-9FFFF write-back
[ 0.000000] A0000-BFFFF uncachable
[ 0.000000] C0000-FFFFF write-protect
[ 0.000000] MTRR variable ranges enabled:
[ 0.000000] 0 base 0000000000 mask 7F00000000 write-back
[ 0.000000] 1 base 0100000000 mask 7FE0000000 write-back
[ 0.000000] 2 base 00E0000000 mask 7FE0000000 uncachable
[ 0.000000] 3 base 00DE000000 mask 7FFE000000 uncachable
[ 0.000000] 4 base 00DD000000 mask 7FFF000000 uncachable
[ 0.000000] 5 base 011FE00000 mask 7FFFE00000 uncachable
[ 0.000000] 6 disabled
[ 0.000000] 7 disabled
[ 0.000000] 8 disabled
[ 0.000000] 9 disabled
[ 0.000000] x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
[ 0.000000] e820: update [mem 0xdd000000-0xffffffff] usable ==> reserved
[ 0.000000] e820: last_pfn = 0xdc000 max_arch_pfn = 0x400000000
[ 0.000000] found SMP MP-table at [mem 0x000fd820-0x000fd82f] mapped at [ffff8800000fd820]
[ 0.000000] Base memory trampoline at [ffff880000097000] 97000 size 24576
[ 0.000000] Using GB pages for direct mapping
[ 0.000000] init_memory_mapping: [mem 0x00000000-0x000fffff]
[ 0.000000] [mem 0x00000000-0x000fffff] page 4k
[ 0.000000] BRK [0x01718000, 0x01718fff] PGTABLE
[ 0.000000] BRK [0x01719000, 0x01719fff] PGTABLE
[ 0.000000] BRK [0x0171a000, 0x0171afff] PGTABLE
[ 0.000000] init_memory_mapping: [mem 0x11fc00000-0x11fdfffff]
[ 0.000000] [mem 0x11fc00000-0x11fdfffff] page 2M
[ 0.000000] BRK [0x0171b000, 0x0171bfff] PGTABLE
[ 0.000000] init_memory_mapping: [mem 0x11c000000-0x11fbfffff]
[ 0.000000] [mem 0x11c000000-0x11fbfffff] page 2M
[ 0.000000] init_memory_mapping: [mem 0x100000000-0x11bffffff]
[ 0.000000] [mem 0x100000000-0x11bffffff] page 2M
[ 0.000000] init_memory_mapping: [mem 0x00100000-0xd6e13fff]
[ 0.000000] [mem 0x00100000-0x001fffff] page 4k
[ 0.000000] [mem 0x00200000-0x3fffffff] page 2M
[ 0.000000] [mem 0x40000000-0xbfffffff] page 1G
[ 0.000000] [mem 0xc0000000-0xd6dfffff] page 2M
[ 0.000000] [mem 0xd6e00000-0xd6e13fff] page 4k
[ 0.000000] init_memory_mapping: [mem 0xd70cb000-0xdb359fff]
[ 0.000000] [mem 0xd70cb000-0xd71fffff] page 4k
[ 0.000000] [mem 0xd7200000-0xdb1fffff] page 2M
[ 0.000000] [mem 0xdb200000-0xdb359fff] page 4k
[ 0.000000] BRK [0x0171c000, 0x0171cfff] PGTABLE
[ 0.000000] BRK [0x0171d000, 0x0171dfff] PGTABLE
[ 0.000000] init_memory_mapping: [mem 0xdb3ba000-0xdb5a9fff]
[ 0.000000] [mem 0xdb3ba000-0xdb5a9fff] page 4k
[ 0.000000] init_memory_mapping: [mem 0xdbfff000-0xdbffffff]
[ 0.000000] [mem 0xdbfff000-0xdbffffff] page 4k
[ 0.000000] ACPI: Early table checksum verification disabled
[ 0.000000] ACPI: RSDP 0x00000000000F0530 000024 (v02 ALASKA)
[ 0.000000] ACPI: XSDT 0x00000000DBCF0088 00008C (v01 ALASKA A M I 01072009 AMI 00010013)
[ 0.000000] ACPI: FACP 0x00000000DBD02B18 00010C (v05 ALASKA A M I 01072009 AMI 00010013)
[ 0.000000] ACPI: DSDT 0x00000000DBCF01A8 012969 (v02 ALASKA A M I 01072009 INTL 20120913)
[ 0.000000] ACPI: FACS 0x00000000DBD25F80 000040
[ 0.000000] ACPI: APIC 0x00000000DBD02C28 000084 (v03 ALASKA A M I 01072009 AMI 00010013)
[ 0.000000] ACPI: FPDT 0x00000000DBD02CB0 000044 (v01 ALASKA A M I 01072009 AMI 00010013)
[ 0.000000] ACPI: FIDT 0x00000000DBD02CF8 00009C (v01 ALASKA A M I 01072009 AMI 00010013)
[ 0.000000] ACPI: MCFG 0x00000000DBD02D98 00003C (v01 ALASKA A M I 01072009 MSFT 00000097)
[ 0.000000] ACPI: HPET 0x00000000DBD02DD8 000038 (v01 ALASKA A M I 01072009 AMI. 00000005)
[ 0.000000] ACPI: SSDT 0x00000000DBD02E10 000315 (v01 SataRe SataTabl 00001000 INTL 20120913)
[ 0.000000] ACPI: UEFI 0x00000000DBD03128 000042 (v01 00000000 00000000)
[ 0.000000] ACPI: SSDT 0x00000000DBD03170 000C7D (v01 Ther_R Ther_Rvp 00001000 INTL 20120913)
[ 0.000000] ACPI: ASF! 0x00000000DBD03DF0 0000A0 (v32 INTEL HCG 00000001 TFSM 000F4240)
[ 0.000000] ACPI: SSDT 0x00000000DBD03E90 000539 (v01 PmRef Cpu0Ist 00003000 INTL 20120913)
[ 0.000000] ACPI: SSDT 0x00000000DBD043D0 000B74 (v01 CpuRef CpuSsdt 00003000 INTL 20120913)
[ 0.000000] ACPI: SSDT 0x00000000DBD04F48 005B10 (v01 SaSsdt SaSsdt 00003000 INTL 20120913)
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] Zone ranges:
[ 0.000000] DMA [mem 0x00001000-0x00ffffff]
[ 0.000000] DMA32 [mem 0x01000000-0xffffffff]
[ 0.000000] Normal [mem 0x100000000-0x11fdfffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x00001000-0x0009cfff]
[ 0.000000] node 0: [mem 0x00100000-0xd6e13fff]
[ 0.000000] node 0: [mem 0xd70cb000-0xdb359fff]
[ 0.000000] node 0: [mem 0xdb3ba000-0xdb5a9fff]
[ 0.000000] node 0: [mem 0xdbfff000-0xdbffffff]
[ 0.000000] node 0: [mem 0x100000000-0x11fdfffff]
[ 0.000000] Initmem setup node 0 [mem 0x00001000-0x11fdfffff]
[ 0.000000] On node 0 totalpages: 1028144
[ 0.000000] DMA zone: 64 pages used for memmap
[ 0.000000] DMA zone: 21 pages reserved
[ 0.000000] DMA zone: 3996 pages, LIFO batch:0
[ 0.000000] DMA32 zone: 13963 pages used for memmap
[ 0.000000] DMA32 zone: 893588 pages, LIFO batch:31
[ 0.000000] Normal zone: 2040 pages used for memmap
[ 0.000000] Normal zone: 130560 pages, LIFO batch:31
[ 0.000000] Reserving Intel graphics stolen memory at 0xdd200000-0xdf1fffff
[ 0.000000] ACPI: PM-Timer IO Port: 0x1808
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x02] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x03] lapic_id[0x01] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x04] lapic_id[0x03] enabled)
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x01] dfl dfl lint[0x0])
[ 0.000000] ACPI: NMI not connected to LINT 1!
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x02] dfl dfl lint[0x0])
[ 0.000000] ACPI: NMI not connected to LINT 1!
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x03] dfl dfl lint[0x0])
[ 0.000000] ACPI: NMI not connected to LINT 1!
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x04] dfl dfl lint[0x0])
[ 0.000000] ACPI: NMI not connected to LINT 1!
[ 0.000000] ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
[ 0.000000] IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, GSI 0-39
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[ 0.000000] ACPI: IRQ0 used by override.
[ 0.000000] ACPI: IRQ9 used by override.
[ 0.000000] Using ACPI (MADT) for SMP configuration information
[ 0.000000] ACPI: HPET id: 0x8086a701 base: 0xfed00000
[ 0.000000] smpboot: Allowing 4 CPUs, 0 hotplug CPUs
[ 0.000000] e820: [mem 0xdf200000-0xf7ffffff] available for PCI devices
[ 0.000000] Booting paravirtualized kernel on bare hardware
[ 0.000000] setup_percpu: NR_CPUS:8 nr_cpumask_bits:8 nr_cpu_ids:4 nr_node_ids:1
[ 0.000000] PERCPU: Embedded 27 pages/cpu @ffff88011fa00000 s72896 r8192 d29504 u524288
[ 0.000000] pcpu-alloc: s72896 r8192 d29504 u524288 alloc=1*2097152
[ 0.000000] pcpu-alloc: [0] 0 1 2 3
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 1012056
[ 0.000000] Kernel command line: BOOT_IMAGE=/boot/vmlinuz block2mtd.block2mtd=PARTUUID=c3d6313e-02,65536,rootfs,5 root=/dev/mtdblock0 rootfstype=squashfs rootwait console=tty0 console=ttyS0,38400n8 noinitrd
[ 0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.000000] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes)
[ 0.000000] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes)
[ 0.000000] xsave: enabled xstate_bv 0x7, cntxt size 0x340 using standard form
[ 0.000000] AGP: Checking aperture...
[ 0.000000] AGP: No AGP bridge found
[ 0.000000] Calgary: detecting Calgary via BIOS EBDA area
[ 0.000000] Calgary: Unable to locate Rio Grande table in EBDA - bailing!
[ 0.000000] Memory: 3966960K/4112576K available (4119K kernel code, 476K rwdata, 1412K rodata, 744K init, 488K bss, 145616K reserved)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] CONFIG_RCU_FANOUT set to non-default value of 32
[ 0.000000] RCU restricting CPUs from NR_CPUS=8 to nr_cpu_ids=4.
[ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4
[ 0.000000] NR_IRQS:4352 nr_irqs:728 0
[ 0.000000] spurious 8259A interrupt: IRQ7.
[ 0.000000] Console: colour VGA+ 80x25
[ 0.000000] console [tty0] enabled
[ 0.000000] console [ttyS0] enabled
[ 0.000000] hpet clockevent registered
[ 0.000000] tsc: Fast TSC calibration using PIT
[ 0.000000] tsc: Detected 2294.771 MHz processor
[ 0.000001] Calibrating delay loop (skipped), value calculated using timer frequency.. 4589.54 BogoMIPS (lpj=22947710)
[ 0.032218] pid_max: default: 32768 minimum: 301
[ 0.046127] ACPI: Core revision 20140926
[ 0.072255] ACPI: All ACPI Tables successfully acquired
[ 0.088185] Mount-cache hash table entries: 8192 (order: 4, 65536 bytes)
[ 0.108338] Mountpoint-cache hash table entries: 8192 (order: 4, 65536 bytes)
[ 0.129916] CPU: Physical Processor ID: 0
[ 0.142011] CPU: Processor Core ID: 0
[ 0.153055] ENERGY_PERF_BIAS: Set to 'normal', was 'performance'
[ 0.153055] ENERGY_PERF_BIAS: View and update with x86_energy_perf_policy(8)
[ 0.192211] mce: CPU supports 7 MCE banks
[ 0.204307] CPU0: Thermal monitoring enabled (TM1)
[ 0.218727] process: using mwait in idle threads
[ 0.232624] Last level iTLB entries: 4KB 1024, 2MB 1024, 4MB 1024
[ 0.232624] Last level dTLB entries: 4KB 1024, 2MB 1024, 4MB 1024, 1GB 4
[ 0.271082] Freeing SMP alternatives memory: 16K (ffffffff8169a000 - ffffffff8169e000)
[ 0.296192] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=0 pin2=0
[ 0.413698] smpboot: CPU0: Intel(R) Core(TM) i5-4200U CPU @ 1.60GHz (fam: 06, model: 45, stepping: 01)
[ 0.441920] TSC deadline timer enabled
[ 0.441940] Performance Events: PEBS fmt2+, 16-deep LBR, Haswell events, full-width counters, Intel PMU driver.
[ 0.472686] ... version: 3
[ 0.484776] ... bit width: 48
[ 0.497143] ... generic registers: 4
[ 0.509253] ... value mask: 0000ffffffffffff
[ 0.525263] ... max period: 0000ffffffffffff
[ 0.541268] ... fixed-purpose events: 3
[ 0.553375] ... event mask: 000000070000000f
[ 0.569572] x86: Booting SMP configuration:
[ 0.582195] .... node #0, CPUs: #1 #2 #3
[ 0.635049] x86: Booted up 1 node, 4 CPUs
[ 0.647808] smpboot: Total of 4 processors activated (18358.16 BogoMIPS)
[ 0.671656] NET: Registered protocol family 16
[ 0.715047] cpuidle: using governor ladder
[ 0.727451] ACPI FADT declares the system doesn't support PCIe ASPM, so disable it
[ 0.750285] ACPI: bus type PCI registered
[ 0.762387] PCI: Using configuration type 1 for base access
[ 0.809400] ACPI: Added _OSI(Module Device)
[ 0.822017] ACPI: Added _OSI(Processor Device)
[ 0.835428] ACPI: Added _OSI(3.0 _SCP Extensions)
[ 0.849617] ACPI: Added _OSI(Processor Aggregator Device)
[ 0.926064] ACPI: Executed 18 blocks of module-level executable AML code
[ 1.105831] ACPI: Dynamic OEM Table Load:
[ 1.118098] ACPI: SSDT 0xFFFF88011B255C00 0003D3 (v01 PmRef Cpu0Cst 00003001 INTL 20120913)
[ 1.173569] ACPI: Dynamic OEM Table Load:
[ 1.185808] ACPI: SSDT 0xFFFF88011B0E5000 0005AA (v01 PmRef ApIst 00003000 INTL 20120913)
[ 1.241075] ACPI: Dynamic OEM Table Load:
[ 1.253319] ACPI: SSDT 0xFFFF88011A8CC000 000119 (v01 PmRef ApCst 00003000 INTL 20120913)
[ 1.309604] ACPI: Interpreter enabled
[ 1.320685] ACPI: (supports S0 S5)
[ 1.330969] ACPI: Using IOAPIC for interrupt routing
[ 1.345963] PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug
[ 1.374962] ACPI: Power Resource [PG00] (on)
[ 1.420003] ACPI: Power Resource [PG01] (on)
[ 1.473216] ACPI: Power Resource [PG02] (on)
[ 1.525134] ACPI: Power Resource [FN00] (off)
[ 1.538361] ACPI: Power Resource [FN01] (off)
[ 1.551578] ACPI: Power Resource [FN02] (off)
[ 1.564783] ACPI: Power Resource [FN03] (off)
[ 1.578010] ACPI: Power Resource [FN04] (off)
[ 1.592062] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-3e])
[ 1.610665] acpi PNP0A08:00: _OSC: OS supports [Segments MSI]
[ 1.628102] acpi PNP0A08:00: _OSC: not requesting OS control; OS requires [ExtendedConfig ASPM ClockPM MSI]
[ 1.657911] PCI host bridge to bus 0000:00
[ 1.670267] pci_bus 0000:00: root bus resource [bus 00-3e]
[ 1.686792] pci_bus 0000:00: root bus resource [io 0x0000-0x0cf7]
[ 1.705404] pci_bus 0000:00: root bus resource [io 0x0d00-0xffff]
[ 1.724009] pci_bus 0000:00: root bus resource [mem 0x000a0000-0x000bffff]
[ 1.744694] pci_bus 0000:00: root bus resource [mem 0xdf200000-0xfeafffff]
[ 1.765382] pci 0000:00:00.0: [8086:0a04] type 00 class 0x060000
[ 1.765464] pci 0000:00:02.0: [8086:0a16] type 00 class 0x030000
[ 1.765476] pci 0000:00:02.0: reg 0x10: [mem 0xf7800000-0xf7bfffff 64bit]
[ 1.765482] pci 0000:00:02.0: reg 0x18: [mem 0xe0000000-0xefffffff 64bit pref]
[ 1.765487] pci 0000:00:02.0: reg 0x20: [io 0xf000-0xf03f]
[ 1.765561] pci 0000:00:03.0: [8086:0a0c] type 00 class 0x040300
[ 1.765569] pci 0000:00:03.0: reg 0x10: [mem 0xf7f14000-0xf7f17fff 64bit]
[ 1.765664] pci 0000:00:14.0: [8086:9c31] type 00 class 0x0c0330
[ 1.765680] pci 0000:00:14.0: reg 0x10: [mem 0xf7f00000-0xf7f0ffff 64bit]
[ 1.765736] pci 0000:00:14.0: PME# supported from D3hot D3cold
[ 1.765792] pci 0000:00:16.0: [8086:9c3a] type 00 class 0x078000
[ 1.765810] pci 0000:00:16.0: reg 0x10: [mem 0xf7f1c000-0xf7f1c01f 64bit]
[ 1.765868] pci 0000:00:16.0: PME# supported from D0 D3hot D3cold
[ 1.765932] pci 0000:00:1b.0: [8086:9c20] type 00 class 0x040300
[ 1.765948] pci 0000:00:1b.0: reg 0x10: [mem 0xf7f10000-0xf7f13fff 64bit]
[ 1.766003] pci 0000:00:1b.0: PME# supported from D0 D3hot D3cold
[ 1.766057] pci 0000:00:1c.0: [8086:9c14] type 01 class 0x060400
[ 1.766116] pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold
[ 1.766174] pci 0000:00:1c.3: [8086:9c16] type 01 class 0x060400
[ 1.766233] pci 0000:00:1c.3: PME# supported from D0 D3hot D3cold
[ 1.766289] pci 0000:00:1c.4: [8086:9c18] type 01 class 0x060400
[ 1.766355] pci 0000:00:1c.4: PME# supported from D0 D3hot D3cold
[ 1.766420] pci 0000:00:1d.0: [8086:9c26] type 00 class 0x0c0320
[ 1.766439] pci 0000:00:1d.0: reg 0x10: [mem 0xf7f1a000-0xf7f1a3ff]
[ 1.766525] pci 0000:00:1d.0: PME# supported from D0 D3hot D3cold
[ 1.766587] pci 0000:00:1f.0: [8086:9c43] type 00 class 0x060100
[ 1.766749] pci 0000:00:1f.2: [8086:9c03] type 00 class 0x010601
[ 1.766763] pci 0000:00:1f.2: reg 0x10: [io 0xf0b0-0xf0b7]
[ 1.766770] pci 0000:00:1f.2: reg 0x14: [io 0xf0a0-0xf0a3]
[ 1.766776] pci 0000:00:1f.2: reg 0x18: [io 0xf090-0xf097]
[ 1.766782] pci 0000:00:1f.2: reg 0x1c: [io 0xf080-0xf083]
[ 1.766789] pci 0000:00:1f.2: reg 0x20: [io 0xf060-0xf07f]
[ 1.766795] pci 0000:00:1f.2: reg 0x24: [mem 0xf7f19000-0xf7f197ff]
[ 1.766829] pci 0000:00:1f.2: PME# supported from D3hot
[ 1.766880] pci 0000:00:1f.3: [8086:9c22] type 00 class 0x0c0500
[ 1.766893] pci 0000:00:1f.3: reg 0x10: [mem 0xf7f18000-0xf7f180ff 64bit]
[ 1.766911] pci 0000:00:1f.3: reg 0x20: [io 0xf040-0xf05f]
[ 1.767046] pci 0000:01:00.0: [8086:1539] type 00 class 0x020000
[ 1.767065] pci 0000:01:00.0: reg 0x10: [mem 0xf7e00000-0xf7e1ffff]
[ 1.767091] pci 0000:01:00.0: reg 0x18: [io 0xe000-0xe01f]
[ 1.767106] pci 0000:01:00.0: reg 0x1c: [mem 0xf7e20000-0xf7e23fff]
[ 1.767222] pci 0000:01:00.0: PME# supported from D0 D3hot D3cold
[ 1.767263] pci 0000:00:1c.0: PCI bridge to [bus 01]
[ 1.782241] pci 0000:00:1c.0: bridge window [io 0xe000-0xefff]
[ 1.782245] pci 0000:00:1c.0: bridge window [mem 0xf7e00000-0xf7efffff]
[ 1.782311] pci 0000:02:00.0: [14e4:4353] type 00 class 0x028000
[ 1.782333] pci 0000:02:00.0: reg 0x10: [mem 0xf7d00000-0xf7d03fff 64bit]
[ 1.782457] pci 0000:02:00.0: supports D1 D2
[ 1.782458] pci 0000:02:00.0: PME# supported from D0 D3hot D3cold
[ 1.782498] pci 0000:00:1c.3: PCI bridge to [bus 02]
[ 1.797468] pci 0000:00:1c.3: bridge window [mem 0xf7d00000-0xf7dfffff]
[ 1.797545] pci 0000:03:00.0: [8086:1539] type 00 class 0x020000
[ 1.797563] pci 0000:03:00.0: reg 0x10: [mem 0xf7c00000-0xf7c1ffff]
[ 1.797590] pci 0000:03:00.0: reg 0x18: [io 0xd000-0xd01f]
[ 1.797603] pci 0000:03:00.0: reg 0x1c: [mem 0xf7c20000-0xf7c23fff]
[ 1.797729] pci 0000:03:00.0: PME# supported from D0 D3hot D3cold
[ 1.797770] pci 0000:00:1c.4: PCI bridge to [bus 03]
[ 1.812865] pci 0000:00:1c.4: bridge window [io 0xd000-0xdfff]
[ 1.812868] pci 0000:00:1c.4: bridge window [mem 0xf7c00000-0xf7cfffff]
[ 1.812910] pci_bus 0000:00: on NUMA node 0
[ 1.814019] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 10 *11 12 14 15)
[ 1.835591] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 10 11 12 14 15) *0, disabled.
[ 1.862389] ACPI: PCI Interrupt Link [LNKC] (IRQs *3 4 5 6 10 11 12 14 15)
[ 1.883946] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 *10 11 12 14 15)
[ 1.905512] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 10 11 12 14 15) *0, disabled.
[ 1.930669] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 10 11 12 14 15) *0, disabled.
[ 1.955823] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 *5 6 10 11 12 14 15)
[ 1.977391] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 10 *11 12 14 15)
[ 1.999190] ACPI: Enabled 4 GPEs in block 00 to 7F
[ 2.013898] SCSI subsystem initialized
[ 2.025237] libata version 3.00 loaded.
[ 2.025247] ACPI: bus type USB registered
[ 2.037379] usbcore: registered new interface driver usbfs
[ 2.053901] usbcore: registered new interface driver hub
[ 2.069911] usbcore: registered new device driver usb
[ 2.085174] PCI: Using ACPI for IRQ routing
[ 2.097814] PCI: pci_cache_line_size set to 64 bytes
[ 2.097884] e820: reserve RAM buffer [mem 0x0009d800-0x0009ffff]
[ 2.097886] e820: reserve RAM buffer [mem 0xd6e14000-0xd7ffffff]
[ 2.097887] e820: reserve RAM buffer [mem 0xdb35a000-0xdbffffff]
[ 2.097888] e820: reserve RAM buffer [mem 0xdb5aa000-0xdbffffff]
[ 2.097890] e820: reserve RAM buffer [mem 0x11fe00000-0x11fffffff]
[ 2.098027] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0, 0, 0, 0, 0, 0
[ 2.117307] hpet0: 8 comparators, 64-bit 14.318180 MHz counter
[ 2.136872] amd_nb: Cannot enumerate AMD northbridges
[ 2.152105] Switched to clocksource hpet
[ 2.165623] pnp: PnP ACPI init
[ 2.175059] system 00:00: [io 0x0a00-0x0a2f] has been reserved
[ 2.192891] system 00:00: [io 0x0a30-0x0a3f] has been reserved
[ 2.210714] system 00:00: [io 0x0a40-0x0a4f] has been reserved
[ 2.228542] system 00:00: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 2.228764] pnp 00:01: [dma 0 disabled]
[ 2.228801] pnp 00:01: Plug and Play ACPI device, IDs PNP0501 (active)
[ 2.229254] system 00:02: [io 0x0680-0x069f] has been reserved
[ 2.247071] system 00:02: [io 0xffff] has been reserved
[ 2.263074] system 00:02: [io 0xffff] has been reserved
[ 2.279085] system 00:02: [io 0xffff] has been reserved
[ 2.295090] system 00:02: [io 0x1800-0x18fe] could not be reserved
[ 2.313955] system 00:02: [io 0x164e-0x164f] has been reserved
[ 2.331781] system 00:02: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 2.331818] pnp 00:03: Plug and Play ACPI device, IDs PNP0b00 (active)
[ 2.331849] system 00:04: [io 0x1854-0x1857] has been reserved
[ 2.349661] system 00:04: Plug and Play ACPI device, IDs INT3f0d PNP0c02 (active)
[ 2.349803] system 00:05: [mem 0xfed1c000-0xfed1ffff] has been reserved
[ 2.369696] system 00:05: [mem 0xfed10000-0xfed17fff] has been reserved
[ 2.389600] system 00:05: [mem 0xfed18000-0xfed18fff] has been reserved
[ 2.409506] system 00:05: [mem 0xfed19000-0xfed19fff] has been reserved
[ 2.429409] system 00:05: [mem 0xf8000000-0xfbffffff] has been reserved
[ 2.449315] system 00:05: [mem 0xfed20000-0xfed3ffff] has been reserved
[ 2.469219] system 00:05: [mem 0xfed90000-0xfed93fff] has been reserved
[ 2.489126] system 00:05: [mem 0xfed45000-0xfed8ffff] has been reserved
[ 2.509030] system 00:05: [mem 0xff000000-0xffffffff] has been reserved
[ 2.528935] system 00:05: [mem 0xfee00000-0xfeefffff] could not be reserved
[ 2.549880] system 00:05: [mem 0xf7fe0000-0xf7feffff] has been reserved
[ 2.569783] system 00:05: [mem 0xf7ff0000-0xf7ffffff] has been reserved
[ 2.589689] system 00:05: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 2.590002] system 00:06: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 2.590329] pnp: PnP ACPI: found 7 devices
[ 2.607981] pci 0000:00:1c.0: PCI bridge to [bus 01]
[ 2.622955] pci 0000:00:1c.0: bridge window [io 0xe000-0xefff]
[ 2.641298] pci 0000:00:1c.0: bridge window [mem 0xf7e00000-0xf7efffff]
[ 2.661727] pci 0000:00:1c.3: PCI bridge to [bus 02]
[ 2.676688] pci 0000:00:1c.3: bridge window [mem 0xf7d00000-0xf7dfffff]
[ 2.697118] pci 0000:00:1c.4: PCI bridge to [bus 03]
[ 2.712083] pci 0000:00:1c.4: bridge window [io 0xd000-0xdfff]
[ 2.730429] pci 0000:00:1c.4: bridge window [mem 0xf7c00000-0xf7cfffff]
[ 2.750857] pci_bus 0000:00: resource 4 [io 0x0000-0x0cf7]
[ 2.750859] pci_bus 0000:00: resource 5 [io 0x0d00-0xffff]
[ 2.750861] pci_bus 0000:00: resource 6 [mem 0x000a0000-0x000bffff]
[ 2.750862] pci_bus 0000:00: resource 7 [mem 0xdf200000-0xfeafffff]
[ 2.750864] pci_bus 0000:01: resource 0 [io 0xe000-0xefff]
[ 2.750865] pci_bus 0000:01: resource 1 [mem 0xf7e00000-0xf7efffff]
[ 2.750867] pci_bus 0000:02: resource 1 [mem 0xf7d00000-0xf7dfffff]
[ 2.750868] pci_bus 0000:03: resource 0 [io 0xd000-0xdfff]
[ 2.750870] pci_bus 0000:03: resource 1 [mem 0xf7c00000-0xf7cfffff]
[ 2.750892] NET: Registered protocol family 2
[ 2.764132] TCP established hash table entries: 32768 (order: 6, 262144 bytes)
[ 2.785959] TCP bind hash table entries: 32768 (order: 7, 524288 bytes)
[ 2.805958] TCP: Hash tables configured (established 32768 bind 32768)
[ 2.825625] TCP: reno registered
[ 2.835375] UDP hash table entries: 2048 (order: 4, 65536 bytes)
[ 2.853480] UDP-Lite hash table entries: 2048 (order: 4, 65536 bytes)
[ 2.872908] NET: Registered protocol family 1
[ 2.886062] pci 0000:00:02.0: Video device with shadowed ROM
[ 2.901827] PCI: CLS 64 bytes, default 64
[ 2.901874] PCI-DMA: Using software bounce buffering for IO (SWIOTLB)
[ 2.921268] software IO TLB [mem 0xd735a000-0xdb35a000] (64MB) mapped at [ffff8800d735a000-ffff8800db359fff]
[ 2.950999] RAPL PMU detected, hw unit 2^-14 Joules, API unit is 2^-32 Joules, 4 fixed counters 655360 ms ovfl timer
[ 2.982845] futex hash table entries: 1024 (order: 4, 65536 bytes)
[ 3.003160] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 3.020713] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 3.050121] msgmni has been set to 7748
[ 3.061776] io scheduler noop registered
[ 3.073617] io scheduler deadline registered (default)
[ 3.089526] input: Sleep Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0E:00/input/input0
[ 3.114705] ACPI: Sleep Button [SLPB]
[ 3.125791] input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input1
[ 3.150963] ACPI: Power Button [PWRB]
[ 3.162044] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input2
[ 3.184353] ACPI: Power Button [PWRF]
[ 3.195768] Monitor-Mwait will be used to enter C-1 state
[ 3.195774] Monitor-Mwait will be used to enter C-2 state
[ 3.195779] Monitor-Mwait will be used to enter C-3 state
[ 3.195788] ACPI: acpi_idle registered with cpuidle
[ 3.196523] thermal LNXTHERM:00: registered as thermal_zone0
[ 3.213577] ACPI: Thermal Zone [TZ00] (28 C)
[ 3.226617] thermal LNXTHERM:01: registered as thermal_zone1
[ 3.243664] ACPI: Thermal Zone [TZ01] (30 C)
[ 3.256616] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[ 3.296337] 00:01: ttyS0 at I/O 0x3f8 (irq = 4, base_baud = 115200) is a 16550A
[ 3.318672] Non-volatile memory driver v1.3
[ 3.331358] Guest personality initialized and is inactive
[ 3.347617] VMCI host device registered (name=vmci, major=10, minor=63)
[ 3.367515] Initialized host personality
[ 3.379423] VMware PVSCSI driver - version 1.0.5.0-k
[ 3.394431] ahci 0000:00:1f.2: version 3.0
[ 3.394531] ahci 0000:00:1f.2: irq 40 for MSI/MSI-X
[ 3.411488] ahci 0000:00:1f.2: AHCI 0001.0300 32 slots 4 ports 6 Gbps 0x1 impl SATA mode
[ 3.435871] ahci 0000:00:1f.2: flags: 64bit ncq pm led clo only pio slum part deso sadm sds apst
[ 3.462835] scsi host0: ahci
[ 3.471663] scsi host1: ahci
[ 3.480453] scsi host2: ahci
[ 3.489266] scsi host3: ahci
[ 3.498045] ata1: SATA max UDMA/133 abar m2048@0xf7f19000 port 0xf7f19100 irq 40
[ 3.520345] ata2: DUMMY
[ 3.527758] ata3: DUMMY
[ 3.535165] ata4: DUMMY
[ 3.542676] VMware vmxnet3 virtual NIC driver - version 1.2.1.0-k-NAPI
[ 3.562474] xhci_hcd 0000:00:14.0: xHCI Host Controller
[ 3.578207] xhci_hcd 0000:00:14.0: new USB bus registered, assigned bus number 1
[ 3.600574] xhci_hcd 0000:00:14.0: cache line size of 64 is not supported
[ 3.600585] xhci_hcd 0000:00:14.0: irq 41 for MSI/MSI-X
[ 3.600693] hub 1-0:1.0: USB hub found
[ 3.612016] hub 1-0:1.0: 9 ports detected
[ 3.625728] xhci_hcd 0000:00:14.0: xHCI Host Controller
[ 3.641482] xhci_hcd 0000:00:14.0: new USB bus registered, assigned bus number 2
[ 3.663874] hub 2-0:1.0: USB hub found
[ 3.675209] hub 2-0:1.0: 4 ports detected
[ 3.688239] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 3.707903] ehci-pci: EHCI PCI platform driver
[ 3.721408] ehci-pci 0000:00:1d.0: EHCI Host Controller
[ 3.737160] ehci-pci 0000:00:1d.0: new USB bus registered, assigned bus number 3
[ 3.759471] ehci-pci 0000:00:1d.0: debug port 2
[ 3.777001] ehci-pci 0000:00:1d.0: cache line size of 64 is not supported
[ 3.777012] ehci-pci 0000:00:1d.0: irq 23, io mem 0xf7f1a000
[ 3.811253] ehci-pci 0000:00:1d.0: USB 2.0 started, EHCI 1.00
[ 3.828658] hub 3-0:1.0: USB hub found
[ 3.839982] hub 3-0:1.0: 2 ports detected
[ 3.852179] ehci-platform: EHCI generic platform driver
[ 3.867927] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 3.886528] ohci-pci: OHCI PCI platform driver
[ 3.899940] ohci-platform: OHCI generic platform driver
[ 3.901169] ata1: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
[ 3.902761] ata1.00: supports DRM functions and may not be fully accessible
[ 3.902931] ata1.00: disabling queued TRIM support
[ 3.902932] ata1.00: ATA-9: Samsung SSD 850 EVO mSATA 250GB, EMT41B6Q, max UDMA/133
[ 3.902933] ata1.00: 488397168 sectors, multi 1: LBA48 NCQ (depth 31/32), AA
[ 3.903592] ata1.00: supports DRM functions and may not be fully accessible
[ 3.903711] ata1.00: disabling queued TRIM support
[ 3.904061] ata1.00: configured for UDMA/133
[ 3.904140] scsi 0:0:0:0: Direct-Access ATA Samsung SSD 850 1B6Q PQ: 0 ANSI: 5
[ 3.904262] sd 0:0:0:0: [sda] 488397168 512-byte logical blocks: (250 GB/232 GiB)
[ 3.904296] sd 0:0:0:0: [sda] Write Protect is off
[ 3.904298] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 3.904305] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 3.904650] sda: sda1 sda2 < sda5 >
[ 3.904805] sd 0:0:0:0: [sda] Attached SCSI disk
[ 4.146697] uhci_hcd: USB Universal Host Controller Interface driver
[ 4.165860] usbcore: registered new interface driver usb-storage
[ 4.183961] i8042: PNP: No PS/2 controller found. Probing ports directly.
[ 4.204666] tsc: Refined TSC clocksource calibration: 2294.687 MHz
[ 4.204825] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 4.204830] serio: i8042 AUX port at 0x60,0x64 irq 12
[ 4.204884] rtc_cmos 00:03: RTC can wake from S4
[ 4.205086] rtc_cmos 00:03: rtc core: registered rtc_cmos as rtc0
[ 4.205131] rtc_cmos 00:03: alarms up to one month, y3k, 242 bytes nvram, hpet irqs
[ 4.205140] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.11
[ 4.205164] iTCO_wdt: Found a Lynx Point_LP TCO device (Version=2, TCOBASE=0x1860)
[ 4.205237] iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
[ 4.205270] hidraw: raw HID events driver (C) Jiri Kosina
[ 4.205331] TCP: cubic registered
[ 4.205344] NET: Registered protocol family 17
[ 4.205357] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this.
[ 4.205363] Bridge firewalling registered
[ 4.205365] 8021q: 802.1Q VLAN Support v1.8
[ 4.205382] NET: Registered protocol family 40
[ 4.600812] usb 1-3: new high-speed USB device number 2 using xhci_hcd
[ 4.700756] usb 3-1: new high-speed USB device number 2 using ehci-pci
[ 4.861431] hub 3-1:1.0: USB hub found
[ 4.872926] hub 3-1:1.0: 8 ports detected
[ 4.950618] usb 1-4: new low-speed USB device number 3 using xhci_hcd
[ 5.116765] usb 1-4: ep 0x81 - rounding interval to 64 microframes, ep desc says 80 microframes
[ 5.142972] usb 1-4: ep 0x82 - rounding interval to 64 microframes, ep desc says 80 microframes
[ 5.340401] usb 1-6: new high-speed USB device number 4 using xhci_hcd
[ 5.480488] Switched to clocksource tsc
[ 5.512467] hub 1-6:1.0: USB hub found
[ 5.524100] hub 1-6:1.0: 4 ports detected
[ 5.710192] usb 1-7: new full-speed USB device number 5 using xhci_hcd
[ 5.921880] usb 1-7: ep 0x82 - rounding interval to 64 microframes, ep desc says 80 microframes
[ 6.320129] usb 2-4: new SuperSpeed USB device number 2 using xhci_hcd
[ 6.366664] usb-storage 2-4:1.0: USB Mass Storage device detected
[ 6.385165] scsi host4: usb-storage 2-4:1.0
[ 7.653401] scsi 4:0:0:0: Direct-Access Samsung Flash Drive 1100 PQ: 0 ANSI: 6
[ 7.678382] sd 4:0:0:0: [sdb] 125304832 512-byte logical blocks: (64.1 GB/59.7 GiB)
[ 7.701935] sd 4:0:0:0: [sdb] Write Protect is off
[ 7.716386] sd 4:0:0:0: [sdb] Mode Sense: 43 00 00 00
[ 7.716832] sd 4:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 7.747468] sdb: sdb1 sdb2
[ 7.757592] sd 4:0:0:0: [sdb] Attached SCSI removable disk
[ 8.459281] Creating 1 MTD partitions on "rootfs":
[ 8.473735] 0x000000000000-0x000006000000 : "rootfs"
[ 8.488816] mtd: device 0 (rootfs) set to be root filesystem
[ 8.506516] 1 squashfs-split partitions found on MTD device rootfs
[ 8.525137] 0x000000990000-0x000006000000 : "rootfs_data"
[ 8.541526] block2mtd: mtd0: [rootfs] erase_size = 64KiB [65536]
[ 8.559658] rtc_cmos 00:03: setting system clock to 2017-03-12 20:41:34 UTC (1489351294)
[ 8.586740] VFS: Mounted root (squashfs filesystem) readonly on device 31:0.
[ 8.608283] Freeing unused kernel memory: 744K (ffffffff815e0000 - ffffffff8169a000)
[ 8.781661] init: Console is alive
[ 8.791986] init: - watchdog -
[ 9.178752] pps_core: LinuxPPS API ver. 1 registered
[ 9.193709] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[ 9.221318] PTP clock support registered
[ 9.800888] init: - preinit -
[ 9.888507] random: mktemp urandom read with 80 bits of entropy available
[ 11.942529] mount_root: loading kmods from internal overlay
[ 12.533074] random: nonblocking pool is initialized
[ 14.060033] jffs2: notice: (847) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
[ 14.106518] block: attempting to load /tmp/jffs_cfg/upper/etc/config/fstab
[ 14.127360] block: extroot: not configured
[ 14.177423] jffs2: notice: (844) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
[ 14.231772] block: attempting to load /tmp/jffs_cfg/upper/etc/config/fstab
[ 14.252669] block: extroot: not configured
[ 14.315586] mount_root: switching to jffs2 overlay
[ 14.361650] EXT4-fs (sdb1): mounted filesystem without journal. Opts: (null)
[ 14.429708] procd: - early -
[ 14.438442] procd: - watchdog -
[ 15.069744] procd: - ubus -
[ 16.084494] procd: - init -
[ 16.249638] NET: Registered protocol family 10
[ 16.264477] bcma: bus0: Found chip with id 43224, rev 0x01 and package 0x0A
[ 16.285452] bcma: bus0: Core 0 found: ChipCommon (manuf 0x4BF, id 0x800, rev 0x22, class 0x0)
[ 16.311162] bcma: bus0: Core 1 found: IEEE 802.11 (manuf 0x4BF, id 0x812, rev 0x17, class 0x0)
[ 16.337141] bcma: bus0: Core 2 found: PCIe (manuf 0x4BF, id 0x820, rev 0x0F, class 0x0)
[ 16.411771] bcma: bus0: Bus registered
[ 16.425085] RPC: Registered named UNIX socket transport module.
[ 16.442934] RPC: Registered udp transport module.
[ 16.457115] RPC: Registered tcp transport module.
[ 16.471302] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 16.491475] tun: Universal TUN/TAP device driver, 1.6
[ 16.506724] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[ 16.525717] e1000: Intel(R) PRO/1000 Network Driver - version 7.3.21-k8-NAPI
[ 16.546955] e1000: Copyright (c) 1999-2006 Intel Corporation.
[ 16.564949] igb: Intel(R) Gigabit Ethernet Network Driver - version 5.2.15-k
[ 16.586167] igb: Copyright (c) 2007-2014 Intel Corporation.
[ 16.603444] igb 0000:01:00.0: irq 42 for MSI/MSI-X
[ 16.603448] igb 0000:01:00.0: irq 43 for MSI/MSI-X
[ 16.603451] igb 0000:01:00.0: irq 44 for MSI/MSI-X
[ 16.603453] igb 0000:01:00.0: irq 45 for MSI/MSI-X
[ 16.603456] igb 0000:01:00.0: irq 46 for MSI/MSI-X
[ 16.633649] igb 0000:01:00.0: added PHC on eth0
[ 16.647334] igb 0000:01:00.0: Intel(R) Gigabit Ethernet Network Connection
[ 16.668018] igb 0000:01:00.0: eth0: (PCIe:2.5Gb/s:Width x1) 00:0e:c4:d0:1b:e7
[ 16.689483] igb 0000:01:00.0: eth0: PBA No: FFFFFF-0FF
[ 16.704960] igb 0000:01:00.0: Using MSI-X interrupts. 2 rx queue(s), 2 tx queue(s)
[ 16.728354] igb 0000:03:00.0: irq 47 for MSI/MSI-X
[ 16.728359] igb 0000:03:00.0: irq 48 for MSI/MSI-X
[ 16.728363] igb 0000:03:00.0: irq 49 for MSI/MSI-X
[ 16.728367] igb 0000:03:00.0: irq 50 for MSI/MSI-X
[ 16.728371] igb 0000:03:00.0: irq 51 for MSI/MSI-X
[ 16.758788] igb 0000:03:00.0: added PHC on eth1
[ 16.772456] igb 0000:03:00.0: Intel(R) Gigabit Ethernet Network Connection
[ 16.793145] igb 0000:03:00.0: eth1: (PCIe:2.5Gb/s:Width x1) 00:0e:c4:d0:1b:e8
[ 16.814633] igb 0000:03:00.0: eth1: PBA No: FFFFFF-0FF
[ 16.830129] igb 0000:03:00.0: Using MSI-X interrupts. 2 rx queue(s), 2 tx queue(s)
[ 16.868083] gre: GRE over IPv4 demultiplexor driver
[ 16.882996] ip_gre: GRE over IPv4 tunneling driver
[ 16.900033] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[ 16.919664] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 16.937297] Hooked IMQ after mangle on PREROUTING
[ 16.951767] Hooked IMQ after nat on POSTROUTING
[ 16.965706] IMQ driver loaded successfully. (numdevs = 2, numqueues = 1, imq_dev_accurate_stats = 1)
[ 16.993219] Hooking IMQ before NAT on PREROUTING.
[ 17.007672] Hooking IMQ after NAT on POSTROUTING.
[ 17.022440] Netfilter messages via NETLINK v0.30.
[ 17.036935] ip_set: protocol 6
[ 17.048186] i2c /dev entries driver
[ 17.060110] Linux video capture interface: v2.00
[ 17.075678] u32 classifier
[ 17.083886] input device check on
[ 17.094972] Actions configured
[ 17.105518] Mirror/redirect action on
[ 17.118777] fuse init (API version 7.23)
[ 17.131757] usbcore: registered new interface driver cdc_acm
[ 17.148802] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
[ 17.173179] usbcore: registered new interface driver cdc_wdm
[ 17.190647] Loading modules backported from Linux version v4.4-rc5-1913-gc8fdf68
[ 17.212947] Backport generated by backports.git backports-20151218-0-g2f58d9d
[ 17.235051] e100: Intel(R) PRO/100 Network Driver, 3.5.24-k2-NAPI
[ 17.253478] e100: Copyright(c) 1999-2006 Intel Corporation
[ 17.270949] e1000e: Intel(R) PRO/1000 Network Driver - 2.3.2-k
[ 17.288533] e1000e: Copyright(c) 1999 - 2014 Intel Corporation.
[ 17.307660] Ebtables v2.0 registered
[ 17.318785] gspca_main: v2.14.0 registered
[ 17.331305] usbcore: registered new interface driver ov534
[ 17.348054] usbcore: registered new interface driver gspca_zc3xx
[ 17.366603] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 17.383994] nf_conntrack version 0.5.0 (16384 buckets, 65536 max)
[ 17.487598] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null)
[ 17.522357] Adding 4111356k swap on /dev/sda5. Priority:-1 extents:1 across:4111356k SS
[ 17.563482] EXT4-fs (sdb1): mounted filesystem without journal. Opts: (null)
[ 17.625196] usbcore: registered new interface driver ums-alauda
[ 17.643147] usbcore: registered new interface driver ums-cypress
[ 17.661324] usbcore: registered new interface driver ums-datafab
[ 17.679522] usbcore: registered new interface driver ums-freecom
[ 17.697707] usbcore: registered new interface driver ums-isd200
[ 17.715662] usbcore: registered new interface driver ums-jumpshot
[ 17.734079] usbcore: registered new interface driver ums-karma
[ 17.751779] usbcore: registered new interface driver ums-sddr09
[ 17.769715] usbcore: registered new interface driver ums-sddr55
[ 17.787659] usbcore: registered new interface driver ums-usbat
[ 17.808748] input: ELMCU iPazzPort as /devices/pci0000:00/0000:00:14.0/usb1/1-4/1-4:1.0/0003:0C40:8000.0001/input/input7
[ 17.841510] hid-generic 0003:0C40:8000.0001: input,hidraw0: USB HID v1.11 Keyboard [ELMCU iPazzPort] on usb-0000:00:14.0-4/input0
[ 17.880767] input: ELMCU iPazzPort as /devices/pci0000:00/0000:00:14.0/usb1/1-4/1-4:1.1/0003:0C40:8000.0002/input/input8
[ 17.913515] hid-generic 0003:0C40:8000.0002: input,hidraw1: USB HID v1.11 Mouse [ELMCU iPazzPort] on usb-0000:00:14.0-4/input1
[ 17.948793] usbcore: registered new interface driver usbhid
[ 17.965588] usbhid: USB HID core driver
[ 17.977369] usbcore: registered new interface driver usblp
[ 17.994784] usbcore: registered new interface driver usbserial
[ 18.012435] usbcore: registered new interface driver usbserial_generic
[ 18.032098] usbserial: USB Serial support registered for generic
[ 18.032571] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null)
[ 18.041810] Adding 4111356k swap on /dev/sda5. Priority:-1 extents:1 across:4111356k SS
[ 18.055943] EXT4-fs (sdb1): mounted filesystem without journal. Opts: (null)
[ 18.119417] usbcore: registered new interface driver uvcvideo
[ 18.138610] USB Video Class driver (1.1.1)
[ 18.154354] xt_time: kernel timezone is -0000
[ 18.167697] usbcore: registered new interface driver cdc_ether
[ 18.185555] usbcore: registered new interface driver cdc_ncm
[ 18.212753] usbcore: registered new interface driver huawei_cdc_ncm
[ 18.235985] PPP generic driver version 2.4.2
[ 18.249015] PPP MPPE Compression module registered
[ 18.263631] NET: Registered protocol family 24
[ 18.277185] PPTP driver version 0.8.5
[ 18.288512] usbcore: registered new interface driver qmi_wwan
[ 18.306057] usbcore: registered new interface driver rndis_host
[ 18.324012] usbcore: registered new interface driver sierra
[ 18.340821] usbserial: USB Serial support registered for Sierra USB modem
[ 18.361443] usbcore: registered new interface driver sierra_net
[ 18.381459] b43-phy0: Broadcom 43224 WLAN found (core revision 23)
[ 18.400476] b43-phy0: Found PHY: Analog 8, Type 4 (N), Revision 6
[ 18.418832] b43-phy0: Found Radio: Manuf 0x17F, ID 0x2056, Revision 11, Version 0
[ 18.441900] Broadcom 43xx driver loaded [ Features: PNL ]
[ 18.459774] Broadcom 43xx-legacy driver loaded [ Features: PLD ]
[ 18.514286] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
[ 18.514591] usbcore: registered new interface driver brcmfmac
[ 18.533336] usbcore: registered new interface driver cdc_mbim
[ 18.536029] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null)
[ 18.545872] Adding 4111356k swap on /dev/sda5. Priority:-1 extents:1 across:4111356k SS
[ 18.560099] EXT4-fs (sdb1): mounted filesystem without journal. Opts: (null)
[ 18.619773] usbcore: registered new interface driver option
[ 18.636561] usbserial: USB Serial support registered for GSM modem (1-port)
[ 18.658002] usbcore: registered new interface driver qcserial
[ 18.675324] usbserial: USB Serial support registered for Qualcomm USB modem
[ 18.830651] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null)
[ 18.864016] Adding 4111356k swap on /dev/sda5. Priority:-1 extents:1 across:4111356k SS
[ 18.904783] EXT4-fs (sdb1): mounted filesystem without journal. Opts: (null)
[ 19.170475] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null)
[ 19.203656] Adding 4111356k swap on /dev/sda5. Priority:-1 extents:1 across:4111356k SS
[ 19.244769] EXT4-fs (sdb1): mounted filesystem without journal. Opts: (null)
[ 19.490439] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null)
[ 19.524503] Adding 4111356k swap on /dev/sda5. Priority:-1 extents:1 across:4111356k SS
[ 19.565449] EXT4-fs (sdb1): mounted filesystem without journal. Opts: (null)
[ 19.755069] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null)
[ 19.788833] Adding 4111356k swap on /dev/sda5. Priority:-1 extents:1 across:4111356k SS
[ 19.836183] EXT4-fs (sdb1): mounted filesystem without journal. Opts: (null)
[ 20.406944] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null)
[ 20.463551] 8021q: adding VLAN 0 to HW filter on device eth0
[ 20.480757] device eth0 entered promiscuous mode
[ 20.494936] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
[ 20.522973] EXT4-fs (sdb1): mounted filesystem without journal. Opts: (null)
[ 20.741390] 8021q: adding VLAN 0 to HW filter on device eth1
[ 20.758444] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready
[ 23.361338] igb 0000:01:00.0 eth0: igb: eth0 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX
[ 23.388878] br-lan: port 1(eth0) entered forwarding state
[ 23.405140] br-lan: port 1(eth0) entered forwarding state
[ 23.421579] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[ 25.399217] br-lan: port 1(eth0) entered forwarding state