Version 1.10.0 : New stable version with critical security fixes

The latest news about Gargoyle

Moderator: Moderators

kanenas
Posts: 15
Joined: Tue Feb 19, 2013 9:53 am

Re: Version 1.10.0 : New stable version with critical security fixes

Postby kanenas » Wed Nov 01, 2017 1:48 pm

Lantis wrote:Can you please present the same logs when using 36?
I'm just following what the errors say.

Also, what router is this?

I think possibly need to set regulatory region.


This a xiaomi mini (mt7620), https://wiki.openwrt.org/toh/xiaomi/mini
using the channel 36 the system log is


Wed Nov 1 19:41:55 2017 daemon.notice netifd: Network device 'wlan1' link is up
Wed Nov 1 19:41:55 2017 daemon.info dnsmasq[11239]: started, version 2.78 cachesize 150
Wed Nov 1 19:41:55 2017 daemon.info dnsmasq[11239]: DNS service limited to local subnets
Wed Nov 1 19:41:55 2017 daemon.info dnsmasq[11239]: compile time options: no-IPv6 GNU-getopt no-DBus no-i18n no-IDN DHCP no-DHCPv6 no-Lua TFTP no-conntrack no-ipset no-auth no-DNSSEC no-ID loop-detect inotify
Wed Nov 1 19:41:55 2017 daemon.info dnsmasq-dhcp[11239]: DHCP, IP range 10.0.0.223 -- 10.0.0.254, lease time 12h
Wed Nov 1 19:41:55 2017 daemon.info dnsmasq[11239]: using nameserver 95.142.171.235#53 for domain micro
Wed Nov 1 19:41:55 2017 daemon.info dnsmasq[11239]: using nameserver 95.211.32.162#53 for domain micro
Wed Nov 1 19:41:55 2017 daemon.info dnsmasq[11239]: using nameserver 66.244.95.20#53 for domain micro
Wed Nov 1 19:41:55 2017 daemon.info dnsmasq[11239]: using nameserver 95.142.171.235#53 for domain oss
Wed Nov 1 19:41:55 2017 daemon.info dnsmasq[11239]: using nameserver 95.211.32.162#53 for domain oss
Wed Nov 1 19:41:55 2017 daemon.info dnsmasq[11239]: using nameserver 66.244.95.20#53 for domain oss
Wed Nov 1 19:41:55 2017 daemon.info dnsmasq[11239]: using nameserver 95.142.171.235#53 for domain null
Wed Nov 1 19:41:55 2017 daemon.info dnsmasq[11239]: using nameserver 95.211.32.162#53 for domain null
Wed Nov 1 19:41:55 2017 daemon.info dnsmasq[11239]: using nameserver 66.244.95.20#53 for domain null
Wed Nov 1 19:41:55 2017 daemon.info dnsmasq[11239]: using nameserver 95.142.171.235#53 for domain ing
Wed Nov 1 19:41:55 2017 daemon.info dnsmasq[11239]: using nameserver 95.211.32.162#53 for domain ing
Wed Nov 1 19:41:55 2017 daemon.info dnsmasq[11239]: using nameserver 66.244.95.20#53 for domain ing
Wed Nov 1 19:41:55 2017 daemon.info dnsmasq[11239]: using nameserver 95.142.171.235#53 for domain indy
Wed Nov 1 19:41:55 2017 daemon.info dnsmasq[11239]: using nameserver 95.211.32.162#53 for domain indy
Wed Nov 1 19:41:55 2017 daemon.info dnsmasq[11239]: using nameserver 66.244.95.20#53 for domain indy
Wed Nov 1 19:41:55 2017 daemon.info dnsmasq[11239]: using nameserver 95.142.171.235#53 for domain gopher
Wed Nov 1 19:41:55 2017 daemon.info dnsmasq[11239]: using nameserver 95.211.32.162#53 for domain gopher
Wed Nov 1 19:41:55 2017 daemon.info dnsmasq[11239]: using nameserver 66.244.95.20#53 for domain gopher
Wed Nov 1 19:41:55 2017 daemon.info dnsmasq[11239]: using nameserver 95.142.171.235#53 for domain geek
Wed Nov 1 19:41:55 2017 daemon.info dnsmasq[11239]: using nameserver 95.211.32.162#53 for domain geek
Wed Nov 1 19:41:55 2017 daemon.info dnsmasq[11239]: using nameserver 66.244.95.20#53 for domain geek
Wed Nov 1 19:41:55 2017 daemon.info dnsmasq[11239]: using nameserver 95.142.171.235#53 for domain fur
Wed Nov 1 19:41:55 2017 daemon.info dnsmasq[11239]: using nameserver 95.211.32.162#53 for domain fur
Wed Nov 1 19:41:55 2017 daemon.info dnsmasq[11239]: using nameserver 66.244.95.20#53 for domain fur
Wed Nov 1 19:41:55 2017 daemon.info dnsmasq[11239]: using nameserver 95.142.171.235#53 for domain free
Wed Nov 1 19:41:55 2017 daemon.info dnsmasq[11239]: using nameserver 95.211.32.162#53 for domain free
Wed Nov 1 19:41:55 2017 daemon.info dnsmasq[11239]: using nameserver 66.244.95.20#53 for domain free
Wed Nov 1 19:41:55 2017 daemon.info dnsmasq[11239]: using nameserver 95.142.171.235#53 for domain bbs
Wed Nov 1 19:41:55 2017 daemon.info dnsmasq[11239]: using nameserver 95.211.32.162#53 for domain bbs
Wed Nov 1 19:41:55 2017 daemon.info dnsmasq[11239]: using nameserver 66.244.95.20#53 for domain bbs
Wed Nov 1 19:41:55 2017 daemon.info dnsmasq[11239]: using 12 more nameservers
Wed Nov 1 19:41:55 2017 daemon.info dnsmasq[11239]: reading /tmp/resolv.conf.auto
Wed Nov 1 19:41:55 2017 daemon.info dnsmasq[11239]: using nameserver 95.142.171.235#53 for domain micro
Wed Nov 1 19:41:55 2017 daemon.info dnsmasq[11239]: using nameserver 95.211.32.162#53 for domain micro
Wed Nov 1 19:41:55 2017 daemon.info dnsmasq[11239]: using nameserver 66.244.95.20#53 for domain micro
Wed Nov 1 19:41:55 2017 daemon.info dnsmasq[11239]: using nameserver 95.142.171.235#53 for domain oss
Wed Nov 1 19:41:55 2017 daemon.info dnsmasq[11239]: using nameserver 95.211.32.162#53 for domain oss
Wed Nov 1 19:41:55 2017 daemon.info dnsmasq[11239]: using nameserver 66.244.95.20#53 for domain oss
Wed Nov 1 19:41:55 2017 daemon.info dnsmasq[11239]: using nameserver 95.142.171.235#53 for domain null
Wed Nov 1 19:41:55 2017 daemon.info dnsmasq[11239]: using nameserver 95.211.32.162#53 for domain null
Wed Nov 1 19:41:55 2017 daemon.info dnsmasq[11239]: using nameserver 66.244.95.20#53 for domain null
Wed Nov 1 19:41:55 2017 daemon.info dnsmasq[11239]: using nameserver 95.142.171.235#53 for domain ing
Wed Nov 1 19:41:55 2017 daemon.info dnsmasq[11239]: using nameserver 95.211.32.162#53 for domain ing
Wed Nov 1 19:41:55 2017 daemon.info dnsmasq[11239]: using nameserver 66.244.95.20#53 for domain ing
Wed Nov 1 19:41:55 2017 daemon.info dnsmasq[11239]: using nameserver 95.142.171.235#53 for domain indy
Wed Nov 1 19:41:55 2017 daemon.info dnsmasq[11239]: using nameserver 95.211.32.162#53 for domain indy
Wed Nov 1 19:41:55 2017 daemon.info dnsmasq[11239]: using nameserver 66.244.95.20#53 for domain indy
Wed Nov 1 19:41:55 2017 daemon.info dnsmasq[11239]: using nameserver 95.142.171.235#53 for domain gopher
Wed Nov 1 19:41:55 2017 daemon.info dnsmasq[11239]: using nameserver 95.211.32.162#53 for domain gopher
Wed Nov 1 19:41:55 2017 daemon.info dnsmasq[11239]: using nameserver 66.244.95.20#53 for domain gopher
Wed Nov 1 19:41:55 2017 daemon.info dnsmasq[11239]: using nameserver 95.142.171.235#53 for domain geek
Wed Nov 1 19:41:55 2017 daemon.info dnsmasq[11239]: using nameserver 95.211.32.162#53 for domain geek
Wed Nov 1 19:41:55 2017 daemon.info dnsmasq[11239]: using nameserver 66.244.95.20#53 for domain geek
Wed Nov 1 19:41:55 2017 daemon.info dnsmasq[11239]: using nameserver 95.142.171.235#53 for domain fur
Wed Nov 1 19:41:55 2017 daemon.info dnsmasq[11239]: using nameserver 95.211.32.162#53 for domain fur
Wed Nov 1 19:41:55 2017 daemon.info dnsmasq[11239]: using nameserver 66.244.95.20#53 for domain fur
Wed Nov 1 19:41:55 2017 daemon.info dnsmasq[11239]: using nameserver 95.142.171.235#53 for domain free
Wed Nov 1 19:41:55 2017 daemon.info dnsmasq[11239]: using nameserver 95.211.32.162#53 for domain free
Wed Nov 1 19:41:55 2017 daemon.info dnsmasq[11239]: using nameserver 66.244.95.20#53 for domain free
Wed Nov 1 19:41:55 2017 daemon.info dnsmasq[11239]: using nameserver 95.142.171.235#53 for domain bbs
Wed Nov 1 19:41:55 2017 daemon.info dnsmasq[11239]: using nameserver 95.211.32.162#53 for domain bbs
Wed Nov 1 19:41:55 2017 daemon.info dnsmasq[11239]: using nameserver 66.244.95.20#53 for domain bbs
Wed Nov 1 19:41:55 2017 daemon.info dnsmasq[11239]: using 16 more nameservers
Wed Nov 1 19:41:55 2017 daemon.info dnsmasq[11239]: read /etc/hosts - 20 addresses
Wed Nov 1 19:41:55 2017 daemon.info dnsmasq[11239]: read /tmp/hosts/dhcp - 1 addresses
Wed Nov 1 19:41:55 2017 daemon.info dnsmasq-dhcp[11239]: read /etc/ethers - 17 addresses
Wed Nov 1 19:41:55 2017 daemon.err uhttpd[1719]: uci: Entry not found
Wed Nov 1 19:41:55 2017 daemon.err uhttpd[1719]: arping: interface eth0 not found: No such device
Wed Nov 1 19:41:57 2017 kern.info kernel: [70671.380000] br-lan: port 2(wlan1) entered forwarding state
Wed Nov 1 19:41:59 2017 daemon.info dnsmasq[11239]: exiting on receipt of SIGTERM
Wed Nov 1 19:41:59 2017 daemon.info dnsmasq[11431]: started, version 2.78 cachesize 150
Wed Nov 1 19:41:59 2017 daemon.info dnsmasq[11431]: DNS service limited to local subnets
Wed Nov 1 19:41:59 2017 daemon.info dnsmasq[11431]: compile time options: no-IPv6 GNU-getopt no-DBus no-i18n no-IDN DHCP no-DHCPv6 no-Lua TFTP no-conntrack no-ipset no-auth no-DNSSEC no-ID loop-detect inotify
Wed Nov 1 19:41:59 2017 daemon.info dnsmasq-dhcp[11431]: DHCP, IP range 10.0.0.223 -- 10.0.0.254, lease time 12h
Wed Nov 1 19:41:59 2017 daemon.info dnsmasq[11431]: using nameserver 95.142.171.235#53 for domain micro
Wed Nov 1 19:41:59 2017 daemon.info dnsmasq[11431]: using nameserver 95.211.32.162#53 for domain micro
Wed Nov 1 19:41:59 2017 daemon.info dnsmasq[11431]: using nameserver 66.244.95.20#53 for domain micro
Wed Nov 1 19:41:59 2017 daemon.info dnsmasq[11431]: using nameserver 95.142.171.235#53 for domain oss
Wed Nov 1 19:41:59 2017 daemon.info dnsmasq[11431]: using nameserver 95.211.32.162#53 for domain oss
Wed Nov 1 19:41:59 2017 daemon.info dnsmasq[11431]: using nameserver 66.244.95.20#53 for domain oss
Wed Nov 1 19:41:59 2017 daemon.info dnsmasq[11431]: using nameserver 95.142.171.235#53 for domain null
Wed Nov 1 19:41:59 2017 daemon.info dnsmasq[11431]: using nameserver 95.211.32.162#53 for domain null
Wed Nov 1 19:41:59 2017 daemon.info dnsmasq[11431]: using nameserver 66.244.95.20#53 for domain null
Wed Nov 1 19:41:59 2017 daemon.info dnsmasq[11431]: using nameserver 95.142.171.235#53 for domain ing
Wed Nov 1 19:41:59 2017 daemon.info dnsmasq[11431]: using nameserver 95.211.32.162#53 for domain ing
Wed Nov 1 19:41:59 2017 daemon.info dnsmasq[11431]: using nameserver 66.244.95.20#53 for domain ing
Wed Nov 1 19:41:59 2017 daemon.info dnsmasq[11431]: using nameserver 95.142.171.235#53 for domain indy
Wed Nov 1 19:41:59 2017 daemon.info dnsmasq[11431]: using nameserver 95.211.32.162#53 for domain indy
Wed Nov 1 19:41:59 2017 daemon.info dnsmasq[11431]: using nameserver 66.244.95.20#53 for domain indy
Wed Nov 1 19:41:59 2017 daemon.info dnsmasq[11431]: using nameserver 95.142.171.235#53 for domain gopher
Wed Nov 1 19:41:59 2017 daemon.info dnsmasq[11431]: using nameserver 95.211.32.162#53 for domain gopher
Wed Nov 1 19:41:59 2017 daemon.info dnsmasq[11431]: using nameserver 66.244.95.20#53 for domain gopher
Wed Nov 1 19:41:59 2017 daemon.info dnsmasq[11431]: using nameserver 95.142.171.235#53 for domain geek
Wed Nov 1 19:41:59 2017 daemon.info dnsmasq[11431]: using nameserver 95.211.32.162#53 for domain geek
Wed Nov 1 19:41:59 2017 daemon.info dnsmasq[11431]: using nameserver 66.244.95.20#53 for domain geek
Wed Nov 1 19:41:59 2017 daemon.info dnsmasq[11431]: using nameserver 95.142.171.235#53 for domain fur
Wed Nov 1 19:41:59 2017 daemon.info dnsmasq[11431]: using nameserver 95.211.32.162#53 for domain fur
Wed Nov 1 19:41:59 2017 daemon.info dnsmasq[11431]: using nameserver 66.244.95.20#53 for domain fur
Wed Nov 1 19:41:59 2017 daemon.info dnsmasq[11431]: using nameserver 95.142.171.235#53 for domain free
Wed Nov 1 19:41:59 2017 daemon.info dnsmasq[11431]: using nameserver 95.211.32.162#53 for domain free
Wed Nov 1 19:41:59 2017 daemon.info dnsmasq[11431]: using nameserver 66.244.95.20#53 for domain free
Wed Nov 1 19:41:59 2017 daemon.info dnsmasq[11431]: using nameserver 95.142.171.235#53 for domain bbs
Wed Nov 1 19:41:59 2017 daemon.info dnsmasq[11431]: using nameserver 95.211.32.162#53 for domain bbs
Wed Nov 1 19:41:59 2017 daemon.info dnsmasq[11431]: using nameserver 66.244.95.20#53 for domain bbs
Wed Nov 1 19:41:59 2017 daemon.info dnsmasq[11431]: using 12 more nameservers
Wed Nov 1 19:41:59 2017 daemon.info dnsmasq[11431]: reading /tmp/resolv.conf.auto
Wed Nov 1 19:41:59 2017 daemon.info dnsmasq[11431]: using nameserver 95.142.171.235#53 for domain micro
Wed Nov 1 19:41:59 2017 daemon.info dnsmasq[11431]: using nameserver 95.211.32.162#53 for domain micro
Wed Nov 1 19:41:59 2017 daemon.info dnsmasq[11431]: using nameserver 66.244.95.20#53 for domain micro
Wed Nov 1 19:41:59 2017 daemon.info dnsmasq[11431]: using nameserver 95.142.171.235#53 for domain oss
Wed Nov 1 19:41:59 2017 daemon.info dnsmasq[11431]: using nameserver 95.211.32.162#53 for domain oss
Wed Nov 1 19:41:59 2017 daemon.info dnsmasq[11431]: using nameserver 66.244.95.20#53 for domain oss
Wed Nov 1 19:41:59 2017 daemon.info dnsmasq[11431]: using nameserver 95.142.171.235#53 for domain null
Wed Nov 1 19:41:59 2017 daemon.info dnsmasq[11431]: using nameserver 95.211.32.162#53 for domain null
Wed Nov 1 19:41:59 2017 daemon.info dnsmasq[11431]: using nameserver 66.244.95.20#53 for domain null
Wed Nov 1 19:41:59 2017 daemon.info dnsmasq[11431]: using nameserver 95.142.171.235#53 for domain ing
Wed Nov 1 19:41:59 2017 daemon.info dnsmasq[11431]: using nameserver 95.211.32.162#53 for domain ing
Wed Nov 1 19:41:59 2017 daemon.info dnsmasq[11431]: using nameserver 66.244.95.20#53 for domain ing
Wed Nov 1 19:41:59 2017 daemon.info dnsmasq[11431]: using nameserver 95.142.171.235#53 for domain indy
Wed Nov 1 19:41:59 2017 daemon.info dnsmasq[11431]: using nameserver 95.211.32.162#53 for domain indy
Wed Nov 1 19:41:59 2017 daemon.info dnsmasq[11431]: using nameserver 66.244.95.20#53 for domain indy
Wed Nov 1 19:41:59 2017 daemon.info dnsmasq[11431]: using nameserver 95.142.171.235#53 for domain gopher
Wed Nov 1 19:41:59 2017 daemon.info dnsmasq[11431]: using nameserver 95.211.32.162#53 for domain gopher
Wed Nov 1 19:41:59 2017 daemon.info dnsmasq[11431]: using nameserver 66.244.95.20#53 for domain gopher
Wed Nov 1 19:41:59 2017 daemon.info dnsmasq[11431]: using nameserver 95.142.171.235#53 for domain geek
Wed Nov 1 19:41:59 2017 daemon.info dnsmasq[11431]: using nameserver 95.211.32.162#53 for domain geek
Wed Nov 1 19:41:59 2017 daemon.info dnsmasq[11431]: using nameserver 66.244.95.20#53 for domain geek
Wed Nov 1 19:41:59 2017 daemon.info dnsmasq[11431]: using nameserver 95.142.171.235#53 for domain fur
Wed Nov 1 19:41:59 2017 daemon.info dnsmasq[11431]: using nameserver 95.211.32.162#53 for domain fur
Wed Nov 1 19:41:59 2017 daemon.info dnsmasq[11431]: using nameserver 66.244.95.20#53 for domain fur
Wed Nov 1 19:41:59 2017 daemon.info dnsmasq[11431]: using nameserver 95.142.171.235#53 for domain free
Wed Nov 1 19:41:59 2017 daemon.info dnsmasq[11431]: using nameserver 95.211.32.162#53 for domain free
Wed Nov 1 19:41:59 2017 daemon.info dnsmasq[11431]: using nameserver 66.244.95.20#53 for domain free
Wed Nov 1 19:41:59 2017 daemon.info dnsmasq[11431]: using nameserver 95.142.171.235#53 for domain bbs
Wed Nov 1 19:41:59 2017 daemon.info dnsmasq[11431]: using nameserver 95.211.32.162#53 for domain bbs
Wed Nov 1 19:41:59 2017 daemon.info dnsmasq[11431]: using nameserver 66.244.95.20#53 for domain bbs
Wed Nov 1 19:41:59 2017 daemon.info dnsmasq[11431]: using 16 more nameservers
Wed Nov 1 19:41:59 2017 daemon.info dnsmasq[11431]: read /etc/hosts - 20 addresses
Wed Nov 1 19:41:59 2017 daemon.info dnsmasq[11431]: read /tmp/hosts/dhcp - 1 addresses
Wed Nov 1 19:41:59 2017 daemon.info dnsmasq-dhcp[11431]: read /etc/ethers - 17 addresses
Wed Nov 1 19:42:30 2017 user.notice firewall: Reloading firewall due to ifup of wan6 (eth0.2)
Wed Nov 1 19:42:33 2017 user.notice firewall: Reloading firewall due to ifup of wan (pppoe-wan)
Wed Nov 1 19:42:42 2017 kern.info kernel: [70716.870000] IMQ driver unloaded successfully.
Wed Nov 1 19:42:42 2017 kern.info kernel: [70716.900000] Hooked IMQ after mangle on INPUT
Wed Nov 1 19:42:42 2017 kern.info kernel: [70716.910000] Hooked IMQ after mangle on FORWARD
Wed Nov 1 19:42:42 2017 kern.info kernel: [70716.910000] IMQ driver loaded successfully. (numdevs = 1, numqueues = 1, imq_dev_accurate_stats = 1)
Wed Nov 1 19:42:42 2017 kern.info kernel: [70716.920000] Hooking IMQ before NAT on PREROUTING.
Wed Nov 1 19:42:42 2017 kern.info kernel: [70716.930000] Hooking IMQ after NAT on POSTROUTING.
Wed Nov 1 19:42:42 2017 daemon.err insmod: module is already loaded - cls_fw
Wed Nov 1 19:42:42 2017 daemon.err insmod: module is already loaded - cls_flow
Wed Nov 1 19:42:42 2017 daemon.err insmod: module is already loaded - sch_hfsc
Wed Nov 1 19:42:42 2017 daemon.err insmod: module is already loaded - sch_sfq
Wed Nov 1 19:42:55 2017 local5.info qosmon[13748]: starting socketfd = 5, statusfd = 4
Wed Nov 1 19:43:01 2017 daemon.info ddns_gargoyle[2543]: Forcing update:
Wed Nov 1 19:43:01 2017 daemon.info ddns_gargoyle[2543]: service provider=freedns.afraid.org
Wed Nov 1 19:43:01 2017 daemon.info ddns_gargoyle[2543]: domain=kan3nas.mooo.com
Wed Nov 1 19:43:02 2017 daemon.info hostapd: wlan1: STA 78:02:f8:27:3e:3c IEEE 802.11: authenticated
Wed Nov 1 19:43:02 2017 daemon.info hostapd: wlan1: STA 78:02:f8:27:3e:3c IEEE 802.11: associated (aid 1)
Wed Nov 1 19:43:02 2017 daemon.info hostapd: wlan1: STA 78:02:f8:27:3e:3c RADIUS: starting accounting session 965661AC3B75429A
Wed Nov 1 19:43:02 2017 daemon.info hostapd: wlan1: STA 78:02:f8:27:3e:3c WPA: pairwise key handshake completed (RSN)
Wed Nov 1 19:43:02 2017 daemon.info dnsmasq-dhcp[11431]: DHCPDISCOVER(br-lan) 78:02:f8:27:3e:3c
Wed Nov 1 19:43:02 2017 daemon.info dnsmasq-dhcp[11431]: DHCPOFFER(br-lan) 10.0.0.246 78:02:f8:27:3e:3c
Wed Nov 1 19:43:02 2017 daemon.info dnsmasq-dhcp[11431]: DHCPREQUEST(br-lan) 10.0.0.246 78:02:f8:27:3e:3c
Wed Nov 1 19:43:02 2017 daemon.info dnsmasq-dhcp[11431]: DHCPACK(br-lan) 10.0.0.246 78:02:f8:27:3e:3c MI5s-denleo
Wed Nov 1 19:43:06 2017 daemon.info ddns_gargoyle[2543]: Could not determine local ip from url: http://checkip.org
Wed Nov 1 19:43:15 2017 daemon.info ddns_gargoyle[2543]: Could not determine local ip from url: http://www.ip-address.org
Wed Nov 1 19:43:15 2017 daemon.info ddns_gargoyle[2543]: Could not determine local ip from url: http://my-ip-address.com
Wed Nov 1 19:43:15 2017 daemon.info ddns_gargoyle[2543]: Could not determine local ip from url: http://www.selfseo.com/what_is_my_ip.php
Wed Nov 1 19:43:16 2017 daemon.info ddns_gargoyle[2543]: Could not determine local ip from url: http://aruljohn.com
Wed Nov 1 19:43:16 2017 daemon.info ddns_gargoyle[2543]: Successfully retrieved local ip from url: http://www.lawrencegoetz.com/programs/ipinfo/
Wed Nov 1 19:43:16 2017 daemon.info ddns_gargoyle[2543]: local IP = 2.87.93.145
Wed Nov 1 19:43:16 2017 daemon.info ddns_gargoyle[2543]: remote IP cannot be determined
Wed Nov 1 19:43:17 2017 daemon.info ddns_gargoyle[2543]: Update failed

and the dmesg is

[26755.260000] device wlan1 entered promiscuous mode
[26755.730000] device wlan0 entered promiscuous mode
[26755.740000] br-lan: port 3(wlan0) entered forwarding state
[26755.740000] br-lan: port 3(wlan0) entered forwarding state
[26755.760000] device wlan0 left promiscuous mode
[26755.760000] br-lan: port 3(wlan0) entered disabled state
[26756.860000] br-lan: port 2(wlan1) entered forwarding state
[26756.860000] br-lan: port 2(wlan1) entered forwarding state
[26758.860000] br-lan: port 2(wlan1) entered forwarding state
[70665.120000] device wlan1 left promiscuous mode
[70665.120000] br-lan: port 2(wlan1) entered disabled state
[70666.120000] br-lan: port 1(eth0.1) entered disabled state
[70666.130000] device eth0.1 left promiscuous mode
[70666.130000] br-lan: port 1(eth0.1) entered disabled state
[70666.170000] device eth0 left promiscuous mode
[70666.180000] 8021q: adding VLAN 0 to HW filter on device eth0
[70666.180000] device eth0 entered promiscuous mode
[70666.200000] device eth0.1 entered promiscuous mode
[70666.200000] br-lan: port 1(eth0.1) entered forwarding state
[70666.210000] br-lan: port 1(eth0.1) entered forwarding state
[70667.190000] pppoe-wan: renamed from ppp0
[70667.640000] device wlan1 entered promiscuous mode
[70667.640000] br-lan: port 2(wlan1) entered forwarding state
[70667.650000] br-lan: port 2(wlan1) entered forwarding state
[70668.150000] br-lan: port 2(wlan1) entered disabled state
[70668.160000] device wlan0 entered promiscuous mode
[70668.170000] device wlan0 left promiscuous mode
[70668.170000] br-lan: port 3(wlan0) entered disabled state
[70668.210000] br-lan: port 1(eth0.1) entered forwarding state
[70669.380000] br-lan: port 2(wlan1) entered forwarding state
[70669.380000] br-lan: port 2(wlan1) entered forwarding state
[70671.380000] br-lan: port 2(wlan1) entered forwarding state
[70716.870000] IMQ driver unloaded successfully.
[70716.900000] Hooked IMQ after mangle on INPUT
[70716.910000] Hooked IMQ after mangle on FORWARD
[70716.910000] IMQ driver loaded successfully. (numdevs = 1, numqueues = 1, imq_dev_accurate_stats = 1)
[70716.920000] Hooking IMQ before NAT on PREROUTING.
[70716.930000] Hooking IMQ after NAT on POSTROUTING.

Please provide more info how can I set the regulatory region.

Lantis
Moderator
Posts: 5094
Joined: Mon Jan 05, 2015 5:33 am
Location: Australia

Re: Version 1.10.0 : New stable version with critical security fixes

Postby Lantis » Wed Nov 01, 2017 3:46 pm

That log missed the important bits. Can’t see anything.
Use the wifi command and try again to avoid the messages we don’t need.

https://wiki.openwrt.org/doc/uci/wirele ... ce_options
See “country”. It may not be required yet.
Routers: Various ar71xx/mvebu/x86-64
http://lantisproject.com/downloads/gargoyle_ispyisail.php for the latest releases

bake15
Posts: 7
Joined: Wed Sep 30, 2009 12:25 pm

Re: Version 1.10.0 : New stable version with critical security fixes

Postby bake15 » Wed Nov 01, 2017 3:53 pm

Changed the 5ghz channel to 36 and its running great now.
24 hours and its not disappeared.

themadsens
Posts: 2
Joined: Wed Nov 01, 2017 3:45 pm

Re: Version 1.10.0 : New stable version with critical security fixes

Postby themadsens » Wed Nov 01, 2017 3:55 pm

30 sec boot loop on MR3220 v1

Hello, and thanks for a very well executed system that I have been using for many years.

For the first time I am having trouble: Just installed 1.10.0 om my TL-MR3220 v1 up from 1.9.1 and it crashes after about 30 second of uptime. Ie. effectively bricked.. I managed to secure the dmesg boot log.

Code: Select all


BusyBox v1.23.2 (2017-10-25 11:54:23 EDT) built-in shell (ash)

------------------------------------------------------------------
|            _____                             _                 |
|           |  __ \                           | |                |
|           | |  \/ __ _ _ __ __ _  ___  _   _| | ___            |
|           | | __ / _` | '__/ _` |/ _ \| | | | |/ _ \           |
|           | |_\ \ (_| | | | (_| | (_) | |_| | |  __/           |
|            \____/\__,_|_|  \__, |\___/ \__, |_|\___|           |
|                             __/ |       __/ |                  |
|                            |___/       |___/                   |
|                                                                |
|----------------------------------------------------------------|
| Gargoyle version 1.10.0   | OpenWrt Chaos Calmer branch        |
| Gargoyle revision ab16f958| OpenWrt commit 216adcf             |
| Built October 25, 2017    | Target  ar71xx/default             |
------------------------------------------------------------------
root@Gargoyle2:~# dmesg
[    0.000000] Linux version 3.18.75 (eric@Osiris) (gcc version 4.8.3 (OpenWrt/Linaro GCC 4.8-2014.04 r49389) ) #2 Wed Oct 25 11:58:01 EDT 2017
[    0.000000] MyLoader: sysp=ffffffff, boardp=ffffffff, parts=ffffffff
[    0.000000] bootconsole [early0] enabled
[    0.000000] CPU0 revision is: 00019374 (MIPS 24Kc)
[    0.000000] SoC: Atheros AR7241 rev 1
[    0.000000] Determined physical RAM map:
[    0.000000]  memory: 02000000 @ 00000000 (usable)
[    0.000000] Initrd not found or empty - disabling initrd
[    0.000000] Zone ranges:
[    0.000000]   Normal   [mem 0x00000000-0x01ffffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x00000000-0x01ffffff]
[    0.000000] Initmem setup node 0 [mem 0x00000000-0x01ffffff]
[    0.000000] On node 0 totalpages: 8192
[    0.000000] free_area_init_node: node 0, pgdat 8030ddf0, node_mem_map 81000000
[    0.000000]   Normal zone: 64 pages used for memmap
[    0.000000]   Normal zone: 0 pages reserved
[    0.000000]   Normal zone: 8192 pages, LIFO batch:0
[    0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[    0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[    0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[    0.000000] pcpu-alloc: [0] 0
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 8128
[    0.000000] Kernel command line:  board=TL-MR3220 console=ttyS0,115200 rootfstype=squashfs,jffs2 noinitrd
[    0.000000] PID hash table entries: 128 (order: -3, 512 bytes)
[    0.000000] Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000] Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
[    0.000000] Writing ErrCtl register=00000000
[    0.000000] Readback ErrCtl register=00000000
[    0.000000] Memory: 28716K/32768K available (2428K kernel code, 140K rwdata, 284K rodata, 276K init, 184K bss, 4052K reserved, 0K cma-reserved)
[    0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[    0.000000] NR_IRQS:51
[    0.000000] Clocks: CPU:400.000MHz, DDR:400.000MHz, AHB:200.000MHz, Ref:5.000MHz
[    0.000000] Calibrating delay loop... 265.42 BogoMIPS (lpj=1327104)
[    0.080000] pid_max: default: 32768 minimum: 301
[    0.080000] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.090000] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.100000] NET: Registered protocol family 16
[    0.100000] MIPS: machine is TP-LINK TL-MR3220
[    0.550000] registering PCI controller with io_map_base unset
[    0.590000] PCI host bridge to bus 0000:00
[    0.600000] pci_bus 0000:00: root bus resource [mem 0x10000000-0x13ffffff]
[    0.600000] pci_bus 0000:00: root bus resource [io  0x0000]
[    0.610000] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[    0.610000] pci 0000:00:00.0: [168c:002b] type 00 class 0x028000
[    0.610000] pci 0000:00:00.0: fixup device configuration
[    0.620000] pci 0000:00:00.0: reg 0x10: [mem 0x10000000-0x1000ffff 64bit]
[    0.620000] pci 0000:00:00.0: supports D1
[    0.620000] pci 0000:00:00.0: PME# supported from D0 D1 D3hot
[    0.620000] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 00
[    0.620000] pci 0000:00:00.0: BAR 0: assigned [mem 0x10000000-0x1000ffff 64bit]
[    0.620000] pci 0000:00:00.0: using irq 40 for pin 1
[    0.630000] Switched to clocksource MIPS
[    0.630000] NET: Registered protocol family 2
[    0.640000] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[    0.640000] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[    0.650000] TCP: Hash tables configured (established 1024 bind 1024)
[    0.660000] TCP: reno registered
[    0.660000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    0.670000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    0.670000] NET: Registered protocol family 1
[    0.680000] PCI: CLS 0 bytes, default 32
[    0.680000] futex hash table entries: 256 (order: -1, 3072 bytes)
[    0.690000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.700000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    0.710000] msgmni has been set to 56
[    0.720000] io scheduler noop registered
[    0.720000] io scheduler deadline registered (default)
[    0.720000] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
[    0.730000] console [ttyS0] disabled
[    0.760000] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11, base_baud = 12500000) is a 16550A
[    0.760000] console [ttyS0] enabled
[    0.770000] bootconsole [early0] disabled
[    0.780000] m25p80 spi0.0: found en25f32, expected m25p80
[    0.790000] m25p80 spi0.0: en25f32 (4096 Kbytes)
[    0.790000] 5 tp-link partitions found on MTD device spi0.0
[    0.800000] Creating 5 MTD partitions on "spi0.0":
[    0.800000] 0x000000000000-0x000000020000 : "u-boot"
[    0.810000] 0x000000020000-0x00000011b200 : "kernel"
[    0.810000] 0x00000011b200-0x0000003f0000 : "rootfs"
[    0.820000] mtd: device 2 (rootfs) set to be root filesystem
[    0.830000] 1 squashfs-split partitions found on MTD device rootfs
[    0.830000] 0x000000380000-0x0000003f0000 : "rootfs_data"
[    0.840000] 0x0000003f0000-0x000000400000 : "art"
[    0.850000] 0x000000020000-0x0000003f0000 : "firmware"
[    0.880000] libphy: ag71xx_mdio: probed
[    1.480000] ag71xx-mdio.1: Found an AR7240/AR9330 built-in switch
[    1.520000] eth0: Atheros AG71xx at 0xba000000, irq 5, mode:GMII
[    2.110000] ag71xx ag71xx.0: connected to PHY at ag71xx-mdio.1:04 [uid=004dd041, driver=Generic PHY]
[    2.120000] eth1: Atheros AG71xx at 0xb9000000, irq 4, mode:MII
[    2.120000] TCP: cubic registered
[    2.130000] NET: Registered protocol family 17
[    2.130000] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this.
[    2.140000] Bridge firewalling registered
[    2.150000] 8021q: 802.1Q VLAN Support v1.8
[    2.160000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
[    2.170000] Freeing unused kernel memory: 276K
[    3.490000] init: Console is alive
[    3.500000] init: - watchdog -
[    5.540000] init: - preinit -
[    6.320000] random: procd urandom read with 9 bits of entropy available
[    7.890000] eth0: link up (1000Mbps/Full duplex)
[    8.720000] jffs2: notice: (329) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
[    8.740000] mount_root: switching to jffs2 overlay
[    8.790000] eth0: link down
[    8.800000] procd: - early -
[    8.800000] procd: - watchdog -
[    9.670000] procd: - ubus -
[   10.680000] procd: - init -
[   11.980000] tun: Universal TUN/TAP device driver, 1.6
[   11.990000] tun: (C) 1999-2004 Max Krasnyansky <maxk _at_ qualcomm com>
[   12.000000] gre: GRE over IPv4 demultiplexor driver
[   12.010000] ip_gre: GRE over IPv4 tunneling driver
[   12.030000] nf_conntrack version 0.5.0 (453 buckets, 1812 max)
[   12.060000]    Hooked IMQ after mangle on PREROUTING
[   12.070000]    Hooked IMQ after nat on POSTROUTING
[   12.070000] IMQ driver loaded successfully. (numdevs = 2, numqueues = 1, imq_dev_accurate_stats = 1)
[   12.080000]    Hooking IMQ before NAT on PREROUTING.
[   12.090000]    Hooking IMQ after NAT on POSTROUTING.
[   12.110000] u32 classifier
[   12.110000]     input device check on
[   12.120000]     Actions configured
[   12.120000] Mirror/redirect action on
[   12.220000] Loading modules backported from Linux version v4.4-rc5-1913-gc8fdf68
[   12.230000] Backport generated by backports.git backports-20151218-0-g2f58d9d
[   12.280000] Ebtables v2.0 registered
[   12.290000] ip_tables: (C) 2000-2006 Netfilter Core Team
[   12.430000] Netfilter messages via NETLINK v0.30.
[   12.570000] xt_time: kernel timezone is -0000
[   12.770000] PPP generic driver version 2.4.2
[   12.790000] PPP MPPE Compression module registered
[   12.790000] NET: Registered protocol family 24
[   12.800000] PPTP driver version 0.8.5
[   12.910000] PCI: Enabling device 0000:00:00.0 (0000 -> 0002)
[   12.930000] ath: phy0: Ignoring endianness difference in EEPROM magic bytes.
[   12.930000] ath: phy0: Enable LNA combining
[   12.940000] ath: EEPROM regdomain: 0x0
[   12.940000] ath: EEPROM indicates default country code should be used
[   12.940000] ath: doing EEPROM country->regdmn map search
[   12.940000] ath: country maps to regdmn code: 0x3a
[   12.940000] ath: Country alpha2 being used: US
[   12.940000] ath: Regpair used: 0x3a
[   12.950000] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
[   12.960000] ieee80211 phy0: Atheros AR9285 Rev:2 mem=0xb0000000, irq=40
[   22.930000] device eth0 entered promiscuous mode
[   22.960000] device eth1 entered promiscuous mode
[   22.970000] br-lan: port 2(eth1) entered forwarding state
[   22.970000] br-lan: port 2(eth1) entered forwarding state
[   23.980000] br-lan: port 2(eth1) entered disabled state
[   24.910000] eth0: link up (1000Mbps/Full duplex)
[   24.910000] br-lan: port 1(eth0) entered forwarding state
[   24.920000] br-lan: port 1(eth0) entered forwarding state
[   25.790000] device wlan0 entered promiscuous mode
[   25.800000] br-lan: port 3(wlan0) entered forwarding state
[   25.800000] br-lan: port 3(wlan0) entered forwarding state
[   25.980000] br-lan: port 3(wlan0) entered disabled state
[   26.920000] br-lan: port 1(eth0) entered forwarding state
[   28.230000] br-lan: port 3(wlan0) entered forwarding state
[   28.230000] br-lan: port 3(wlan0) entered forwarding state
[   30.230000] br-lan: port 3(wlan0) entered forwarding state
root@Gargoyle2:~# packet_write_wait: Connection to 192.168.1.42 port 22: Broken pipe

ispyisail
Moderator
Posts: 4654
Joined: Mon Apr 06, 2009 3:15 am
Location: New Zealand

Re: Version 1.10.0 : New stable version with critical security fixes

Postby ispyisail » Wed Nov 01, 2017 4:12 pm

I've had the same problem

failsafe / refalsh will fix the problem

If you are quick you should able to reset via GUI

Image


themadsens wrote:30 sec boot loop on MR3220 v1

Hello, and thanks for a very well executed system that I have been using for many years.

For the first time I am having trouble: Just installed 1.10.0 om my TL-MR3220 v1 up from 1.9.1 and it crashes after about 30 second of uptime. Ie. effectively bricked.. I managed to secure the dmesg boot log.

Code: Select all


BusyBox v1.23.2 (2017-10-25 11:54:23 EDT) built-in shell (ash)

------------------------------------------------------------------
|            _____                             _                 |
|           |  __ \                           | |                |
|           | |  \/ __ _ _ __ __ _  ___  _   _| | ___            |
|           | | __ / _` | '__/ _` |/ _ \| | | | |/ _ \           |
|           | |_\ \ (_| | | | (_| | (_) | |_| | |  __/           |
|            \____/\__,_|_|  \__, |\___/ \__, |_|\___|           |
|                             __/ |       __/ |                  |
|                            |___/       |___/                   |
|                                                                |
|----------------------------------------------------------------|
| Gargoyle version 1.10.0   | OpenWrt Chaos Calmer branch        |
| Gargoyle revision ab16f958| OpenWrt commit 216adcf             |
| Built October 25, 2017    | Target  ar71xx/default             |
------------------------------------------------------------------
root@Gargoyle2:~# dmesg
[    0.000000] Linux version 3.18.75 (eric@Osiris) (gcc version 4.8.3 (OpenWrt/Linaro GCC 4.8-2014.04 r49389) ) #2 Wed Oct 25 11:58:01 EDT 2017
[    0.000000] MyLoader: sysp=ffffffff, boardp=ffffffff, parts=ffffffff
[    0.000000] bootconsole [early0] enabled
[    0.000000] CPU0 revision is: 00019374 (MIPS 24Kc)
[    0.000000] SoC: Atheros AR7241 rev 1
[    0.000000] Determined physical RAM map:
[    0.000000]  memory: 02000000 @ 00000000 (usable)
[    0.000000] Initrd not found or empty - disabling initrd
[    0.000000] Zone ranges:
[    0.000000]   Normal   [mem 0x00000000-0x01ffffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x00000000-0x01ffffff]
[    0.000000] Initmem setup node 0 [mem 0x00000000-0x01ffffff]
[    0.000000] On node 0 totalpages: 8192
[    0.000000] free_area_init_node: node 0, pgdat 8030ddf0, node_mem_map 81000000
[    0.000000]   Normal zone: 64 pages used for memmap
[    0.000000]   Normal zone: 0 pages reserved
[    0.000000]   Normal zone: 8192 pages, LIFO batch:0
[    0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[    0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[    0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[    0.000000] pcpu-alloc: [0] 0
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 8128
[    0.000000] Kernel command line:  board=TL-MR3220 console=ttyS0,115200 rootfstype=squashfs,jffs2 noinitrd
[    0.000000] PID hash table entries: 128 (order: -3, 512 bytes)
[    0.000000] Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000] Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
[    0.000000] Writing ErrCtl register=00000000
[    0.000000] Readback ErrCtl register=00000000
[    0.000000] Memory: 28716K/32768K available (2428K kernel code, 140K rwdata, 284K rodata, 276K init, 184K bss, 4052K reserved, 0K cma-reserved)
[    0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[    0.000000] NR_IRQS:51
[    0.000000] Clocks: CPU:400.000MHz, DDR:400.000MHz, AHB:200.000MHz, Ref:5.000MHz
[    0.000000] Calibrating delay loop... 265.42 BogoMIPS (lpj=1327104)
[    0.080000] pid_max: default: 32768 minimum: 301
[    0.080000] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.090000] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.100000] NET: Registered protocol family 16
[    0.100000] MIPS: machine is TP-LINK TL-MR3220
[    0.550000] registering PCI controller with io_map_base unset
[    0.590000] PCI host bridge to bus 0000:00
[    0.600000] pci_bus 0000:00: root bus resource [mem 0x10000000-0x13ffffff]
[    0.600000] pci_bus 0000:00: root bus resource [io  0x0000]
[    0.610000] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[    0.610000] pci 0000:00:00.0: [168c:002b] type 00 class 0x028000
[    0.610000] pci 0000:00:00.0: fixup device configuration
[    0.620000] pci 0000:00:00.0: reg 0x10: [mem 0x10000000-0x1000ffff 64bit]
[    0.620000] pci 0000:00:00.0: supports D1
[    0.620000] pci 0000:00:00.0: PME# supported from D0 D1 D3hot
[    0.620000] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 00
[    0.620000] pci 0000:00:00.0: BAR 0: assigned [mem 0x10000000-0x1000ffff 64bit]
[    0.620000] pci 0000:00:00.0: using irq 40 for pin 1
[    0.630000] Switched to clocksource MIPS
[    0.630000] NET: Registered protocol family 2
[    0.640000] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[    0.640000] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[    0.650000] TCP: Hash tables configured (established 1024 bind 1024)
[    0.660000] TCP: reno registered
[    0.660000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    0.670000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    0.670000] NET: Registered protocol family 1
[    0.680000] PCI: CLS 0 bytes, default 32
[    0.680000] futex hash table entries: 256 (order: -1, 3072 bytes)
[    0.690000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.700000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    0.710000] msgmni has been set to 56
[    0.720000] io scheduler noop registered
[    0.720000] io scheduler deadline registered (default)
[    0.720000] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
[    0.730000] console [ttyS0] disabled
[    0.760000] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11, base_baud = 12500000) is a 16550A
[    0.760000] console [ttyS0] enabled
[    0.770000] bootconsole [early0] disabled
[    0.780000] m25p80 spi0.0: found en25f32, expected m25p80
[    0.790000] m25p80 spi0.0: en25f32 (4096 Kbytes)
[    0.790000] 5 tp-link partitions found on MTD device spi0.0
[    0.800000] Creating 5 MTD partitions on "spi0.0":
[    0.800000] 0x000000000000-0x000000020000 : "u-boot"
[    0.810000] 0x000000020000-0x00000011b200 : "kernel"
[    0.810000] 0x00000011b200-0x0000003f0000 : "rootfs"
[    0.820000] mtd: device 2 (rootfs) set to be root filesystem
[    0.830000] 1 squashfs-split partitions found on MTD device rootfs
[    0.830000] 0x000000380000-0x0000003f0000 : "rootfs_data"
[    0.840000] 0x0000003f0000-0x000000400000 : "art"
[    0.850000] 0x000000020000-0x0000003f0000 : "firmware"
[    0.880000] libphy: ag71xx_mdio: probed
[    1.480000] ag71xx-mdio.1: Found an AR7240/AR9330 built-in switch
[    1.520000] eth0: Atheros AG71xx at 0xba000000, irq 5, mode:GMII
[    2.110000] ag71xx ag71xx.0: connected to PHY at ag71xx-mdio.1:04 [uid=004dd041, driver=Generic PHY]
[    2.120000] eth1: Atheros AG71xx at 0xb9000000, irq 4, mode:MII
[    2.120000] TCP: cubic registered
[    2.130000] NET: Registered protocol family 17
[    2.130000] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this.
[    2.140000] Bridge firewalling registered
[    2.150000] 8021q: 802.1Q VLAN Support v1.8
[    2.160000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
[    2.170000] Freeing unused kernel memory: 276K
[    3.490000] init: Console is alive
[    3.500000] init: - watchdog -
[    5.540000] init: - preinit -
[    6.320000] random: procd urandom read with 9 bits of entropy available
[    7.890000] eth0: link up (1000Mbps/Full duplex)
[    8.720000] jffs2: notice: (329) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
[    8.740000] mount_root: switching to jffs2 overlay
[    8.790000] eth0: link down
[    8.800000] procd: - early -
[    8.800000] procd: - watchdog -
[    9.670000] procd: - ubus -
[   10.680000] procd: - init -
[   11.980000] tun: Universal TUN/TAP device driver, 1.6
[   11.990000] tun: (C) 1999-2004 Max Krasnyansky <maxk _at_ qualcomm com>
[   12.000000] gre: GRE over IPv4 demultiplexor driver
[   12.010000] ip_gre: GRE over IPv4 tunneling driver
[   12.030000] nf_conntrack version 0.5.0 (453 buckets, 1812 max)
[   12.060000]    Hooked IMQ after mangle on PREROUTING
[   12.070000]    Hooked IMQ after nat on POSTROUTING
[   12.070000] IMQ driver loaded successfully. (numdevs = 2, numqueues = 1, imq_dev_accurate_stats = 1)
[   12.080000]    Hooking IMQ before NAT on PREROUTING.
[   12.090000]    Hooking IMQ after NAT on POSTROUTING.
[   12.110000] u32 classifier
[   12.110000]     input device check on
[   12.120000]     Actions configured
[   12.120000] Mirror/redirect action on
[   12.220000] Loading modules backported from Linux version v4.4-rc5-1913-gc8fdf68
[   12.230000] Backport generated by backports.git backports-20151218-0-g2f58d9d
[   12.280000] Ebtables v2.0 registered
[   12.290000] ip_tables: (C) 2000-2006 Netfilter Core Team
[   12.430000] Netfilter messages via NETLINK v0.30.
[   12.570000] xt_time: kernel timezone is -0000
[   12.770000] PPP generic driver version 2.4.2
[   12.790000] PPP MPPE Compression module registered
[   12.790000] NET: Registered protocol family 24
[   12.800000] PPTP driver version 0.8.5
[   12.910000] PCI: Enabling device 0000:00:00.0 (0000 -> 0002)
[   12.930000] ath: phy0: Ignoring endianness difference in EEPROM magic bytes.
[   12.930000] ath: phy0: Enable LNA combining
[   12.940000] ath: EEPROM regdomain: 0x0
[   12.940000] ath: EEPROM indicates default country code should be used
[   12.940000] ath: doing EEPROM country->regdmn map search
[   12.940000] ath: country maps to regdmn code: 0x3a
[   12.940000] ath: Country alpha2 being used: US
[   12.940000] ath: Regpair used: 0x3a
[   12.950000] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
[   12.960000] ieee80211 phy0: Atheros AR9285 Rev:2 mem=0xb0000000, irq=40
[   22.930000] device eth0 entered promiscuous mode
[   22.960000] device eth1 entered promiscuous mode
[   22.970000] br-lan: port 2(eth1) entered forwarding state
[   22.970000] br-lan: port 2(eth1) entered forwarding state
[   23.980000] br-lan: port 2(eth1) entered disabled state
[   24.910000] eth0: link up (1000Mbps/Full duplex)
[   24.910000] br-lan: port 1(eth0) entered forwarding state
[   24.920000] br-lan: port 1(eth0) entered forwarding state
[   25.790000] device wlan0 entered promiscuous mode
[   25.800000] br-lan: port 3(wlan0) entered forwarding state
[   25.800000] br-lan: port 3(wlan0) entered forwarding state
[   25.980000] br-lan: port 3(wlan0) entered disabled state
[   26.920000] br-lan: port 1(eth0) entered forwarding state
[   28.230000] br-lan: port 3(wlan0) entered forwarding state
[   28.230000] br-lan: port 3(wlan0) entered forwarding state
[   30.230000] br-lan: port 3(wlan0) entered forwarding state
root@Gargoyle2:~# packet_write_wait: Connection to 192.168.1.42 port 22: Broken pipe

lucianor
Posts: 13
Joined: Wed Dec 21, 2016 1:58 pm

Re: Version 1.10.0 : New stable version with critical security fixes

Postby lucianor » Wed Nov 01, 2017 9:00 pm

Same problem with 5ghz on TP-Link TL-WDR4300 v1.

On logread I see this error message after sending a 'wifi' command. I assume wlan1 is the 5ghz radio/network connection:

Code: Select all

Wed Nov  1 22:40:41 2017 kern.info kernel: [63628.830000] device wlan0 left promiscuous mode
Wed Nov  1 22:40:41 2017 kern.info kernel: [63628.830000] br-lan: port 2(wlan0) entered disabled state
Wed Nov  1 22:40:41 2017 daemon.notice netifd: Network device 'wlan0' link is down
Wed Nov  1 22:40:42 2017 daemon.notice netifd: radio1 (4804): Configuration file: /var/run/hostapd-phy1.conf
Wed Nov  1 22:40:42 2017 kern.info kernel: [63629.580000] device wlan1 entered promiscuous mode
Wed Nov  1 22:40:42 2017 kern.info kernel: [63629.580000] br-lan: port 2(wlan1) entered forwarding state
Wed Nov  1 22:40:42 2017 kern.info kernel: [63629.590000] br-lan: port 2(wlan1) entered forwarding state
Wed Nov  1 22:40:42 2017 daemon.notice netifd: radio1 (4804): wlan1: IEEE 802.11 Configured channel (116) not found from the channel list of current mode (2) IEEE 802.11a
Wed Nov  1 22:40:42 2017 daemon.warn hostapd: wlan1: IEEE 802.11 Configured channel (116) not found from the channel list of current mode (2) IEEE 802.11a
Wed Nov  1 22:40:42 2017 daemon.notice netifd: radio1 [b](4804): wlan1: IEEE 802.11 Hardware does not support configured channel[/b]
Wed Nov  1 22:40:42 2017 daemon.warn hostapd: wlan1: IEEE 802.11 Hardware does not support configured channel
Wed Nov  1 22:40:42 2017 daemon.notice netifd: radio1 (4804): Could not select hw_mode and channel. (-3)
Wed Nov  1 22:40:42 2017 daemon.notice netifd: radio1 (4804): wlan1: interface state UNINITIALIZED->DISABLED
Wed Nov  1 22:40:42 2017 daemon.notice netifd: radio1 (4804): wlan1: AP-DISABLED
Wed Nov  1 22:40:42 2017 daemon.notice netifd: radio1 (4804): wlan1: Unable to setup interface.
Wed Nov  1 22:40:42 2017 daemon.notice netifd: radio1 (4804): wlan1: interface state DISABLED->DISABLED
Wed Nov  1 22:40:42 2017 daemon.notice netifd: radio1 (4804): wlan1: AP-DISABLED
Wed Nov  1 22:40:42 2017 daemon.notice netifd: radio1 (4804): hostapd_free_hapd_data: Interface wlan1 wasn't started
Wed Nov  1 22:40:42 2017 daemon.notice netifd: radio1 (4804): nl80211: deinit ifname=wlan1 disabled_11b_rates=0
Wed Nov  1 22:40:42 2017 kern.info kernel: [63629.620000] device wlan1 left promiscuous mode
Wed Nov  1 22:40:42 2017 kern.info kernel: [63629.630000] br-lan: port 2(wlan1) entered disabled state
Wed Nov  1 22:40:42 2017 daemon.notice netifd: radio1 (4804): cat: can't open '/var/run/wifi-phy1.pid': No such file or directory
Wed Nov  1 22:40:42 2017 daemon.notice netifd: radio1 (4804): Command failed: Invalid argument
Wed Nov  1 22:40:42 2017 daemon.notice netifd: radio1 (4804): Device setup failed: HOSTAPD_START_FAILED
Wed Nov  1 22:40:42 2017 daemon.notice netifd: radio0 (4826): Configuration file: /var/run/hostapd-phy0.conf
Wed Nov  1 22:40:42 2017 kern.info kernel: [63629.960000] device wlan0 entered promiscuous mode
Wed Nov  1 22:40:42 2017 kern.info kernel: [63629.960000] br-lan: port 2(wlan0) entered forwarding state
Wed Nov  1 22:40:42 2017 kern.info kernel: [63629.970000] br-lan: port 2(wlan0) entered forwarding state
Wed Nov  1 22:40:42 2017 daemon.notice netifd: radio0 (4826): Using interface wlan0 with hwaddr 30:b5:c2:b4:dd:7e and ssid "Samanta"
Wed Nov  1 22:40:42 2017 daemon.notice netifd: radio0 (4826): wlan0: interface state UNINITIALIZED->ENABLED
Wed Nov  1 22:40:42 2017 daemon.notice netifd: radio0 (4826): wlan0: AP-ENABLED
Wed Nov  1 22:40:43 2017 daemon.notice netifd: Network device 'wlan0' link is up


From the error message below, it seems I have the invalid channel set. After changing it, the 5ghz channel is working just fine.

Code: Select all

Wed Nov  1 22:40:42 2017 daemon.notice netifd: radio1 (4804): wlan1: IEEE 802.11 Configured channel (116) not found from the channel list of current mode (2) IEEE 802.11a
Wed Nov  1 22:40:42 2017 daemon.warn hostapd: wlan1: IEEE 802.11 Configured channel (116) not found from the channel list of current mode (2) IEEE 802.11a
Wed Nov  1 22:40:42 2017 daemon.notice netifd: radio1 [b](4804): wlan1: IEEE 802.11 Hardware does not support configured channel[/b]


So for those having problem with 5ghz, try googling for your router model and available channels for that frequency.

Lantis
Moderator
Posts: 5094
Joined: Mon Jan 05, 2015 5:33 am
Location: Australia

Re: Version 1.10.0 : New stable version with critical security fixes

Postby Lantis » Wed Nov 01, 2017 11:24 pm

Some models do not support DFS channels correctly.
This is possibly a fault of Gargoyle (not including correct packages) or the country regulatory settings may be required to be set.

If you want 5ghz to work, stick low or high in the band. Not in the middle.

If you want to report that your particular model doesn’t work on DFS, I can try and investigate why.
Routers: Various ar71xx/mvebu/x86-64
http://lantisproject.com/downloads/gargoyle_ispyisail.php for the latest releases

kanenas
Posts: 15
Joined: Tue Feb 19, 2013 9:53 am

Re: Version 1.10.0 : New stable version with critical security fixes

Postby kanenas » Thu Nov 02, 2017 4:40 am

Lantis wrote:Some models do not support DFS channels correctly.
This is possibly a fault of Gargoyle (not including correct packages) or the country regulatory settings may be required to be set.

If you want 5ghz to work, stick low or high in the band. Not in the middle.

If you want to report that your particular model doesn’t work on DFS, I can try and investigate why.


Using google and trying various things regarding the regulatory country and DFS it seems that the problem is that by default gargoyle is setup to be on the global regulatory country. Change it to your country code it turns on 5ghz wifi and works perfectly.

I ssh to my router (I am using a ubuntu box e.g. ssh root@192.168.1.1 from the terminal) input my password and using the following commands works perfectly now!

uci show wireless

from there I can see that I am using at least on xiaomi mini(mt7620) radio0 and radio1

uci set wireless.radio0.country=GR
uci set wireless.radio1.country=GR
uci commit wireless

GR is for Greece and then

iw reg get

To check that the country is changed
Last edited by kanenas on Thu Nov 02, 2017 4:43 am, edited 1 time in total.

Lantis
Moderator
Posts: 5094
Joined: Mon Jan 05, 2015 5:33 am
Location: Australia

Re: Version 1.10.0 : New stable version with critical security fixes

Postby Lantis » Thu Nov 02, 2017 4:42 am

Not all routers require it. Some do.

I'm glad we found you a solution.
Regulatory settings are an intended feature in a future version.
Routers: Various ar71xx/mvebu/x86-64
http://lantisproject.com/downloads/gargoyle_ispyisail.php for the latest releases

User avatar
apvm
Posts: 97
Joined: Thu Apr 30, 2015 7:30 am

Re: Version 1.10.0 : New stable version with critical security fixes

Postby apvm » Thu Nov 02, 2017 6:14 pm

Jumping from landline to voip today. Grandstream HT-502 behind router without problem, no need to port forward.


Return to “News”

Who is online

Users browsing this forum: No registered users and 2 guests