Search found 290 matches
- Fri Mar 02, 2012 6:36 pm
- Forum: News
- Topic: Version 1.5.4 & 1.4.7
- Replies: 70
- Views: 233798
Re: Version 1.5.4 & 1.4.7
Just did an upgrade from 1.4.6 to 1.4.7 and a restore of the config, all good no problems on a TP-Link 1043nd.
- Thu Mar 01, 2012 4:42 am
- Forum: Network / Wireless Issues
- Topic: Gargoyle Performance
- Replies: 31
- Views: 29550
Re: Gargoyle Performance
There is no database of performance metrics for different routers so in reality no one can say of what you have observed is typical or not. There is something on small net builder (not with gargoyle) but it gives you a good idea of hardware performance. Check out http://www.smallnetbuilder.com/lanw...
- Thu Mar 01, 2012 1:46 am
- Forum: Network / Wireless Issues
- Topic: Gargoyle Performance
- Replies: 31
- Views: 29550
Re: Gargoyle Performance
I looked at Top while doing a SpeedTest and the CPU numbers were nothing special, I think I rememebr seeing a 13% but in most cases it was about 4-5%. It appears that the CPU is doing very little work, mostly waiting for the next packet to come through. Should point out, this was to a wired PC and n...
- Thu Feb 23, 2012 5:32 am
- Forum: Network / Wireless Issues
- Topic: Gargoyle Performance
- Replies: 31
- Views: 29550
Re: Gargoyle Performance
Tried the mod, not bad, from 46 to 55Mbits per sec with QoS, a 20% performance improvement.
I guess I can live without the stats and I don't really care about the reporting for a home network.
Many thanks!
I guess I can live without the stats and I don't really care about the reporting for a home network.
Many thanks!
- Tue Feb 21, 2012 3:17 am
- Forum: Network / Wireless Issues
- Topic: Gargoyle Performance
- Replies: 31
- Views: 29550
Re: Gargoyle Performance
No no, not over wireless, a wired 1 Gbit connection to the router. Here's the speed test with QoS on http://www.speedtest.net/result/1786578923.png and here it is turned off http://www.speedtest.net/result/1786583163.png The performance is not up to the par of the stock firmware which was generally ...
- Mon Feb 20, 2012 4:31 pm
- Forum: Network / Wireless Issues
- Topic: Gargoyle Performance
- Replies: 31
- Views: 29550
Re: Gargoyle Performance
So what are you saying? If I upgrade to 1.5.3 and put a swap drive on the 1043nd with a USB key I'll get better performance? I note from the status page that I have Memory Usage: 12.9MB / 28.8MB (45%) which seems to indicate I have free memory, so I'l not sure what the USB key will do??? Out of curi...
- Mon Feb 20, 2012 3:51 am
- Forum: Network / Wireless Issues
- Topic: Gargoyle Performance
- Replies: 31
- Views: 29550
Gargoyle Performance
Some performance measures for my 100 Mbit link from Optus. Gargoyle 1.4.6, TP Link 1043nd If I connect directly to the cable modem (no router) I get 98 Mbits/sec via speedtest.net. If I go through Gargoyle I get about 50 Mbits/sec (with QoS on). With QoS off I get about 75 MBits/sec. As a comparison...
- Sat Feb 18, 2012 1:03 am
- Forum: Hardware / Installation Issues
- Topic: Hosts with active connections
- Replies: 5
- Views: 4557
Re: Hosts with active connections
Version is 1.4.6, and I've attached a screen shot.
There does not seem to be any data just a spurious entry???
There does not seem to be any data just a spurious entry???
- Fri Feb 17, 2012 4:57 pm
- Forum: Hardware / Installation Issues
- Topic: Hosts with active connections
- Replies: 5
- Views: 4557
Hosts with active connections
I note on the Connected Hosts page, there is the following entry
(unknown) 10.85.0.1 unknown 0 0 1
What's this, given the the DHCP start is 192.168.1.100???
(unknown) 10.85.0.1 unknown 0 0 1
What's this, given the the DHCP start is 192.168.1.100???
- Fri Feb 17, 2012 4:48 pm
- Forum: Network / Wireless Issues
- Topic: WPS and Gargoyle 1.4.6
- Replies: 1
- Views: 4904
WPS and Gargoyle 1.4.6
Hi, Just installed Gargoyle 1.4.6 on my TP-Link 1043nd. All seems good and am having better luck with the wireless than the stock firmware, which crashed the router using Wireless N. One question I have though, I have a wireless printer and previously used WPS to set it up using the QSS button on th...