Because it's an USB drive...
I connect it to my router when I need it there.
Then I connect it to my laptop when I need it there.
Then I bring it to office...
Etc.
Search found 122 matches
- Mon Jun 10, 2019 4:55 am
- Forum: Other Issues
- Topic: Problems with shared directory
- Replies: 7
- Views: 8044
- Thu May 23, 2019 2:41 am
- Forum: Network / Wireless Issues
- Topic: WNDR3700v2 and NIC teaming
- Replies: 2
- Views: 2999
Re: WNDR3700v2 and NIC teaming
Ok, I will take this as "not possible"
Thanks a lot.
Thanks a lot.
- Wed May 22, 2019 4:32 pm
- Forum: Network / Wireless Issues
- Topic: WNDR3700v2 and NIC teaming
- Replies: 2
- Views: 2999
WNDR3700v2 and NIC teaming
Is it possible to configure NIC teaming with Netgear WNDR3700v2?
I’d like to connect a NAS with dual NIC.
As far as I understand, the NAS supports LACP 802.3ad both on layer 2 or layer 2+3.
Thanks in advance.
I’d like to connect a NAS with dual NIC.
As far as I understand, the NAS supports LACP 802.3ad both on layer 2 or layer 2+3.
Thanks in advance.
- Mon May 20, 2019 4:09 pm
- Forum: Other Issues
- Topic: Problems with shared directory
- Replies: 7
- Views: 8044
Problems with shared directory
Maybe I have hit a bug. My router is a Netgear WNDR3700 V2 with Gargoyle 1.10.0. I have shared a directory of my USB attached drive, which I use to share my audio/video files across my network (share type CIFS) Everything works fine until I unmount the drive, and then plug it again. In this case, th...
- Thu Jan 10, 2019 12:47 pm
- Forum: General Discussion
- Topic: WPA2 Enterprise support (wireless gateway)
- Replies: 4
- Views: 3429
Re: WPA2 Enterprise support (wireless gateway)
Ok, I found the solution. At the end I had to install OpenWRT, remove wpad-mini and install wpad. Then I created the configuration via OpenWRT web interface, and went to check the file /etc/config/wireless Then I reinstalled Gargoyle, and copied the same parameters in the same file. In my case corr...
- Thu Jan 10, 2019 12:46 pm
- Forum: General Discussion
- Topic: WPA2 Enterprise support (wireless gateway)
- Replies: 4
- Views: 3429
Re: WPA2 Enterprise support (wireless gateway)
Ok, I found the solution. At the end I had to install OpenWRT, remove wpad-mini and install wpad. Then I created the configuration via OpenWRT web interface, and went to check the file /etc/config/wireless Then I reinstalled Gargoyle, and copied the same parameters in the same file. In my case corre...
- Thu Jan 10, 2019 12:46 pm
- Forum: Other Issues
- Topic: BUG: OpenVPN config is not being backed up.
- Replies: 2
- Views: 3240
BUG: OpenVPN config is not being backed up.
I had to uninstall and reinstall Gargoyle to make a few tests with OpenWRT. Obviously I did a backup of the config via Gargoyle WebGUI, so it should have been easy to restore once reinstalled. Unfortunately all configurations were backed up, except OpenVPN config (I had it configured as a client). N...
- Tue Jan 08, 2019 3:43 pm
- Forum: General Discussion
- Topic: WPA2 Enterprise support (wireless gateway)
- Replies: 4
- Views: 3429
Re: WPA2 Enterprise support (wireless gateway)
I tried, but could not manage
- Sun Jan 06, 2019 7:36 am
- Forum: General Discussion
- Topic: WPA2 Enterprise support (wireless gateway)
- Replies: 4
- Views: 3429
WPA2 Enterprise support (wireless gateway)
I need to use Gargoyle 1.10 as a wireless gateway, and the network that I need to connect to is using:
802.1x EAP
PEAP
MSCHAPv2
There's no way to configure this via web GUI ...
Can I set up this via SSH?
Can somebody help?
802.1x EAP
PEAP
MSCHAPv2
There's no way to configure this via web GUI ...
Can I set up this via SSH?
Can somebody help?
- Wed Nov 07, 2018 5:04 am
- Forum: Other Issues
- Topic: Wireless Bridge/Repeater mode
- Replies: 7
- Views: 5137
Re: Wireless Bridge/Repeater mode
I have tried many times to unplug/plug the RJ45 cable, and also to run ipconfig /release and ipconfig /renew command.
Wired client takes an IP on the same subnet as the main router (192.168.1.0/24).
Wired client takes an IP on the same subnet as the main router (192.168.1.0/24).