Search found 6049 matches

by Lantis
Fri Jul 09, 2021 4:48 am
Forum: General Discussion
Topic: Connecting one router to another via cable
Replies: 7
Views: 204

Re: Connecting one router to another via cable

If you left the address as 192.168.2.1 then chances are it's still set to that. To access it you'll need to assign a device a static address in the 192.168.2.x range and then plug into the LAN of the device and attempt to access it. Not much risk posting your MAC addresses. The only risk is if someo...
by Lantis
Wed Jul 07, 2021 9:34 pm
Forum: General Discussion
Topic: Connecting one router to another via cable
Replies: 7
Views: 204

Re: Connecting one router to another via cable

The downstream router will have received an IP address from the main one. It will be in the range 192.168.1.x You may need to use the upstream router's DHCP lease list to try and identify the device. Once you have found it again, it may be a good idea to assign it a static address so you can find it...
by Lantis
Wed Jul 07, 2021 4:10 am
Forum: General Discussion
Topic: Connecting one router to another via cable
Replies: 7
Views: 204

Re: Connecting one router to another via cable

The AP side of things looks fine. No reason it would not be broadcasting that I can tell. I would disable the guest networking and retest. As for the connection settings at the top, to get everything on the same network (as it was when you used wireless bridge) you should set this to disabled, and c...
by Lantis
Tue Jul 06, 2021 11:40 pm
Forum: Network / Wireless Issues
Topic: DHCP enabled, but not working.
Replies: 6
Views: 369

Re: DHCP enabled, but not working.

Thanks. Not much i can do without seeing the actual data while the issue is occurring sorry. If you ever go back to that configuration and see the issue again, please capture the same info and let me know. Just as a note, you have your current configuration as an access point, but DHCP is still enab...
by Lantis
Tue Jul 06, 2021 5:54 pm
Forum: Other Issues
Topic: How to Enable Web admin via Telnet
Replies: 5
Views: 4998

Re: How to Enable Web admin via Telnet

The instructions have not changed.
by Lantis
Tue Jul 06, 2021 5:00 am
Forum: Network / Wireless Issues
Topic: DHCP enabled, but not working.
Replies: 6
Views: 369

Re: DHCP enabled, but not working.

Alright.
Can you give an extract of your config files
cat /etc/config/network
cat /etc/config/dhcp

Also the output of
ls -al /etc/rc.d/

Looking to understand why it would not be starting automatically.
by Lantis
Mon Jul 05, 2021 5:54 pm
Forum: Network / Wireless Issues
Topic: DHCP enabled, but not working.
Replies: 6
Views: 369

Re: DHCP enabled, but not working.

What do you mean it stops handing out addresses? How can you tell this is happening? Do you have connectivity issues or something else?
by Lantis
Tue Jun 22, 2021 6:24 pm
Forum: Network / Wireless Issues
Topic: Picostation2 Wireless Brige/Repeater Setup Woes
Replies: 10
Views: 463

Re: Picostation2 Wireless Brige/Repeater Setup Woes

Find the BSSID of the repeated network and connect specifically to that.
OpenWrt allows this, maybe a wifi scanner will show these details on a phone or laptop.
by Lantis
Tue Jun 22, 2021 5:52 am
Forum: Network / Wireless Issues
Topic: Picostation2 Wireless Brige/Repeater Setup Woes
Replies: 10
Views: 463

Re: Picostation2 Wireless Brige/Repeater Setup Woes

For a warehouse, honestly it would be cheaper/quicker to get a spool of cat5/6 cable and just run it along the roof/rafters/walls.
Way better result!
by Lantis
Mon Jun 21, 2021 9:58 pm
Forum: Hardware / Installation Issues
Topic: Router Speed tests
Replies: 33
Views: 50996

Re: Router Speed tests

the new Technicolor modem set to BRIDGED mode, and usingthe same test computer: PING ms 16 DOWNLOAD Mbps 741.86 UPLOAD Mbps 26.83 In bridge mode, is Gargoyle just using DHCP or is it PPPoE authentication? PPPoE will add additional overhead. Otherwise, it is a slightly slower result than i expected ...