Search found 89 matches

by throughwalls
Wed Feb 15, 2012 11:03 pm
Forum: Other Issues
Topic: DMZ host validation error and strange behaviour
Replies: 6
Views: 1916

Re: DMZ host validation error and strange behaviour

I fully understand the results you posted the picture of. I get (almost) the same results, with the exception that my ISP seems to block some different ports. But I still do not understand the results from my original picture, when I have a DMZ host specified which is not available on the network. W...
by throughwalls
Wed Feb 15, 2012 9:22 pm
Forum: Other Issues
Topic: DMZ host validation error and strange behaviour
Replies: 6
Views: 1916

Re: DMZ host validation error and strange behaviour

Also, if you setup a DMZ IP of 192.168.1.254 and there is no machine using that IP, the results from grc.com are either hitting your modem or router instead, not actually using that IP address. This does not make sense to me. If I configure a DMZ machine and it happens to be powered off (or in this...
by throughwalls
Wed Feb 15, 2012 3:05 pm
Forum: Other Issues
Topic: DMZ host validation error and strange behaviour
Replies: 6
Views: 1916

Re: DMZ host validation error and strange behaviour

Yes, there are restrictions on using .0 and .255 for an IP You're usually using .1 thru .254 as normal IP's Interesting. I did not know this. And so I find http://en.wikipedia.org/wiki/IPv4#Addresses_ending_in_0_or_255 Why are you messing with the DMZ? ... Also, if you setup a DMZ IP of 192.168.1.2...
by throughwalls
Wed Feb 15, 2012 10:00 am
Forum: Other Issues
Topic: DMZ host validation error and strange behaviour
Replies: 6
Views: 1916

DMZ host validation error and strange behaviour

I am running 1.4.2. I have a default DHCP subnet of 192.168.1.xxx Bug report : I tried setting up a DMZ host (Firewall menu, Port Forwarding page). When I typed 192.168.1.255 , the validation code makes it glow red and refuses to allow it. When I choose 192.168.1.254, it is happily accepted. I assum...
by throughwalls
Fri Nov 26, 2010 11:09 am
Forum: Hardware / Installation Issues
Topic: reseting a router to default settings
Replies: 3
Views: 6456

Re: reseting a router to default settings

So it sounds like there is no way to get back to default settings within Gargoyle. Instead I need to load a different firmware (e.g. DD-WRT), clearing everything out, and then reload gargoyle.
by throughwalls
Wed Nov 24, 2010 1:30 pm
Forum: Hardware / Installation Issues
Topic: reseting a router to default settings
Replies: 3
Views: 6456

reseting a router to default settings

I have a lovely WRT54G v2. I have installed Gargoyle on it and it worked fine in AP mode. I reconfigured it as a wireless bridge mode, following the instructions, but I can now not connect to it. I have tried the IP address I told it to be, and it does not respond (router and computer are on the sam...
by throughwalls
Mon Aug 30, 2010 5:32 pm
Forum: Other Issues
Topic: problems with upgrade to 1.3.4
Replies: 5
Views: 1901

Re: problems with upgrade to 1.3.4

I'm also having the exact same problem on a WRT54g v2.2 I was able to do a 30/30/30 and roll back to ver 1.2.4 Does Gargoyle respond to a 30/30/30 in general? From prior experience, I thought it did not. Do you have a link to a documentation page on this? In any case, I already have the default set...
by throughwalls
Sat Aug 28, 2010 10:27 pm
Forum: Other Issues
Topic: problems with upgrade to 1.3.4
Replies: 5
Views: 1901

Re: problems with upgrade to 1.3.4

Your second problem I have not really seen. Once you login with "password" you should immediately be prompted to set a new password. It is then necessary to go again to 192.168.1.1 and re-login with the new password. I suspect that your changes are not being saved because you are not actu...
by throughwalls
Sat Aug 28, 2010 2:26 pm
Forum: Other Issues
Topic: problems with upgrade to 1.3.4
Replies: 5
Views: 1901

problems with upgrade to 1.3.4

I have a WRT54G v2 which used to have DD-WRT. I upgraded it yesterday using the DD-WRT gui to the new 1.3.4 The reflashing seemed initially to have worked, but I have two (related?) major problems that I have subsequently found. Problem 1 : When I power on the router, it ignores the cable-connected ...

Go to advanced search