Search found 1373 matches

by DoesItMatter
Fri May 30, 2014 2:24 am
Forum: Hardware / Installation Issues
Topic: v 2.0 TL-WR1043ND with Atheros AR83xx
Replies: 8
Views: 13670

Re: v 2.0 TL-WR1043ND with Atheros AR83xx

http://wiki.openwrt.org/toh/tp-link/tl-wr1043nd View that page for info on WR1043ND-V2 Gargoyle runs on OpenWRT underneath so any hardware questions should be researched on the OpenWRT website/forums/wiki If there is a image available for download - it should flash BUT - as always - you take the ris...
by DoesItMatter
Fri May 30, 2014 2:21 am
Forum: Hardware / Installation Issues
Topic: TL-WR841ND - Flashed ok but..
Replies: 5
Views: 3574

Re: TL-WR841ND - Flashed ok but..

1) Reset to defaults
2) Re-flash 1.6.1
3) Try a different browser (make sure the cache is cleared)

Try the above
by DoesItMatter
Fri May 30, 2014 2:17 am
Forum: General Discussion
Topic: Rosewill 300RT Would I be able to go back Stock
Replies: 1
Views: 739

Re: Rosewill 300RT Would I be able to go back Stock

You should be able to flash back and forth from Gargoyle to DD-WRT

Make sure you are able to serial recover if it's that critical to you

There's always a chance for a bad flash and you might have to
serial recover a router.
by DoesItMatter
Sun May 25, 2014 11:39 pm
Forum: Hardware / Installation Issues
Topic: help
Replies: 7
Views: 3124

Re: help

Could be a corrupted config

Try the steps listed here:

viewtopic.php?f=8&t=2080

You will probably have to re-configure fresh

If you can get back in - don't load an old config - reconfigure fresh!
by DoesItMatter
Sun May 25, 2014 11:37 pm
Forum: Monitoring / Quota / QoS Issues
Topic: Incorrect Date
Replies: 7
Views: 4204

Re: Incorrect Date

Backup your current config

Reset to defaults and see if you can get the time/date to sync properly

If you can, then reload your old config

If the time/date goes wacky again - you have a corrupted config
and you have to again - reset to defaults, then reconfigure fresh
by DoesItMatter
Fri May 23, 2014 12:11 pm
Forum: General Discussion
Topic: help
Replies: 1
Views: 666

Re: help

If you have a WRT54G model, try the 1.4.7 firmware first

See how that works first.
by DoesItMatter
Thu May 22, 2014 10:59 pm
Forum: General Discussion
Topic: Does This Firmware Work With Neatgear's R6100?
Replies: 2
Views: 1139

Re: Does This Firmware Work With Neatgear's R6100?

Not right now

Has to be supported by OpenWRT first before it could get
support for Gargoyle.

Looks like you might have some luck with DD-WRT soon

Also check for Tomato Firmware - that may support it soon too
by DoesItMatter
Thu May 22, 2014 1:10 pm
Forum: Network / Wireless Issues
Topic: Network Setup Advice/Help: Wireless modem to Gargoyle wired
Replies: 4
Views: 3254

Re: Network Setup Advice/Help: Wireless modem to Gargoyle wi

Save yourself a LOT of hassle and get one of these: http://www.dlink.com/us/en/home-solutions/connect/powerline You can then connect the NDR3700 WAN port up over wire and not have to worry about a wireless bridge setup You can find them on sale all the time I run multiple wireless bridges in my hous...
by DoesItMatter
Thu May 22, 2014 11:36 am
Forum: General Discussion
Topic: Is it ok to flash WR941 V3.8 with this firmware
Replies: 2
Views: 1204

Re: Is it ok to flash WR941 V3.8 with this firmware

See this page

http://wiki.openwrt.org/toh/tp-link/tl-wr941nd

Should be fine to flash Gargoyle 1.6.0 or 1.6.1

DO NOT FLASH ANYTHING BELOW 1.5.7 on your WR941 V3.8

You need Attitude Adjustment branch for your V3.8

Versions you could try:

1.5.10
1.5.11
1.6.0
1.6.1
by DoesItMatter
Wed May 21, 2014 1:12 am
Forum: Hardware / Installation Issues
Topic: Transmit Custom Power Issue
Replies: 1
Views: 914

Re: Transmit Custom Power Issue

I just finished upgrading router number 3 TP-Link TL-WR1043N/ND v1 to Gargoyle Version:1.6.1 when I attempt to set the custom transmit power (I don't think my neighbors 2 miles away need to see my signal :lol: ) to something other than 27 it keeps at custom 27 any ideas works fine on version 2 Than...

Go to advanced search