ubiquiti_routerstation_pro
Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision | ||
|
ubiquiti_routerstation_pro [2012/12/05 05:53] ispyisail |
ubiquiti_routerstation_pro [2012/12/05 07:07] (current) ispyisail [Ubiquiti firmware recovery method] |
||
|---|---|---|---|
| Line 11: | Line 11: | ||
| In response to the outstanding demand for our initial RouterStation OEM platform, Ubiquiti Networks announces the RouterStation Pro | In response to the outstanding demand for our initial RouterStation OEM platform, Ubiquiti Networks announces the RouterStation Pro | ||
| - | ===== | + | ==== Features |
| - | Features | + | |
| + | |||
| + | |||
| + | * Item802.3af 48V compatible | ||
| + | * ItemGigabit Ethernet Switch (4 ports) | ||
| + | * Item128MB RAM | ||
| + | * Item16MB Flash | ||
| + | * ItemUSB 2.0 Support | ||
| + | * ItemSDIO Support | ||
| + | * Item680MHz CPU (Option to overclock to 800) | ||
| + | * ItemRobust ESD/Surge Protection for Industrial Applications | ||
| + | * ItemSupport for 3 Ubiquiti SR,XR,or SR71 radios | ||
| + | * ItemBuilt in dB9 connector | ||
| + | * ItemEasy Access to full GPIO signals | ||
| + | |||
| + | ===== Installing Firmware ===== | ||
| + | ==== Ubiquiti firmware recovery method ==== | ||
| + | === Requirements === | ||
| + | |||
| + | * Ubnt Router with power supply | ||
| + | * Windows PC with NIC card | ||
| + | * Ethernet cable for connection between PC and Ubiquiti router | ||
| + | * Network settings of PC: 192.168.1.1/ | ||
| + | * Install [[http:// | ||
| + | * Gargoyle [[http:// | ||
| + | |||
| + | gargoyle_1.5.8-ar71xx-generic-ubnt-rspro-squashfs-factory.bin | ||
| + | |||
| + | === Install Firmware === | ||
| + | * Power off the router | ||
| + | * Press the router reset switch then apply power | ||
| + | * Release the reset button after a few seconds | ||
| + | * LED's should be flashing to indicate recovery mode | ||
| + | * with PC set a fixed IP address 192.168.1.1/ | ||
| + | * Assuming POE, connect Ethernet cable between " | ||
| + | * (optional) Check router response by pinging from PC command line | ||
| + | < | ||
| + | ping 192.168.1.20 | ||
| + | </ | ||
| + | * Run TFTP server | ||
| + | * Select >> Tftp Client | ||
| + | * Select >> Server interface: | ||
| + | * Enter Host Address: | ||
| + | * Select file to flash gargoyle_1.5.8-ar71xx-generic-ubnt-rspro-squashfs-factory.bin | ||
| + | * Click >> Put | ||
| + | {{ : | ||
| + | |||
| + | Wait 10 minutes and router should be flashed with new firmware. | ||
| + | |||
| + | Reset PC NIC back to DHCP then connect PC NIC to LAN port of your router. | ||
| + | |||
| + | You should be able to connect to the gargoyle interface by entering into your browser 192.168.1.1 | ||
| + | |||
| + | |||
| + | |||
| - | * Unordered List Item802.3af 48V compatible | ||
| - | * Unordered List ItemGigabit Ethernet Switch (4 ports) | ||
| - | * Unordered List Item128MB RAM | ||
| - | * Unordered List Item16MB Flash | ||
| - | * Unordered List ItemUSB 2.0 Support | ||
| - | * Unordered List ItemSDIO Support | ||
| - | * Unordered List Item680MHz CPU (Option to overclock to 800) | ||
| - | * Unordered List ItemRobust ESD/Surge Protection for Industrial Applications | ||
| - | * Unordered List ItemSupport for 3 Ubiquiti SR,XR,or SR71 radios | ||
| - | * Unordered List ItemBuilt in dB9 connector | ||
| - | * Unordered List ItemEasy Access to full GPIO signals | ||
ubiquiti_routerstation_pro.1354686817.txt.gz · Last modified: 2012/12/05 05:53 by ispyisail
Page Tools
Except where otherwise noted, content on this wiki is licensed under the following license: CC Attribution-Share Alike 4.0 International
