tp-link_tl-wr1043nd
Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision | ||
|
tp-link_tl-wr1043nd [2015/04/23 05:57] nworbnhoj [Introduction] |
tp-link_tl-wr1043nd [2015/04/26 23:59] (current) nworbnhoj old revision restored (2014/02/16 00:50) |
||
|---|---|---|---|
| Line 1: | Line 1: | ||
| - | ====== TP-Link | + | ====== TP-Link |
| < | < | ||
| WARNING: This document may contain errors which may result in damage to your router. USE AT YOUR OWN RISK. | WARNING: This document may contain errors which may result in damage to your router. USE AT YOUR OWN RISK. | ||
| </ | </ | ||
| + | {{INLINETOC 2 4 }} | ||
| ===== Introduction ===== | ===== Introduction ===== | ||
| - | Installation of Gargoyle on selected TP-Link routers is straight-forward: | ||
| - | - [[tp-link_tl-wr1043nd# | ||
| - | - [[tp-link_tl-wr1043nd# | ||
| - | - Login to your router and [[gargoyle_setup|configure Gargoyle]] | ||
| - | If you run into trouble, then ask a question at the [[http://www.gargoyle-router.com/phpbb/index.php | forum]] or read [[failsafe_mode_recovery]] | + | The TP-Link TL-WR1043ND is becoming |
| - | Gargoyle is built on top of [[http://http://wiki.openwrt.org/toh/tp-link/ | + | //Note: Firmware is still listed as experimental and not all features may work as expected.// |
| - | + | ||
| - | The TP-Link TL-WR1043ND is a very popular Gargoyle router due price and the hardware feature set. | + | |
| - | + | ||
| - | | {{ tplink-wr1043nd.jpg? | + | |
| + | {{ tplink-wr1043nd.jpg }} | ||
| ===== Download firmware ===== | ===== Download firmware ===== | ||
| + | Select the correct firmware for this device. | ||
| - | Go to the [[http://www.gargoyle-router.com/ | + | {{:select.jpg|}} |
| - | **Download: | + | |
| - | **Architecture: | + | |
| - | **Branch:** 1.6 (stable)\\ | + | |
| - | **Version: | + | |
| - | :!: To __replace__ the original TP-LINK | + | Upgrading existing router (Gargoyle or OpenWRT) |
| + | '' | ||
| - | |**TP-WR1043ND-V1.X** | + | Installing new firmware |
| - | |**TP-WR1043ND-V2.X** | + | |
| - | |**TP-WDR3600-V1.X** | + | |
| - | :!: To __upgrade__ Gargoyle or OpenWRT firmware select the **sysupgrade.bin** download. | + | '' |
| + | ===== Install ===== | ||
| + | Open the original TP-Link configuration. | ||
| + | Select " | ||
| + | Select | ||
| - | ===== Install ===== | + | '' |
| - | Open the original TP-Link configuration. | + | |
| - | **Select** //System Tools - Firmware Upgrade// | + | file then click "upgrade" |
| - | **Select** // | + | |
| - | **Click** //upgrade// | + | |
| - | :!: If you get the error message | + | If you get the error message |
| |{{: | |{{: | ||
| Line 55: | Line 46: | ||
| Wait about 5 minutes then you should be able to connect to 192.168.1.1 | Wait about 5 minutes then you should be able to connect to 192.168.1.1 | ||
| - | :!: **Do not unplug the power supply during upgrade.** | + | **Do not unplug the power supply during upgrade.** |
| If after 5 minutes 192.168.1.1 is unresponsive first reboot your PC and try again. If after 20 minutes 192.168.1.1 is unresponsive you may reboot both PC and router. | If after 5 minutes 192.168.1.1 is unresponsive first reboot your PC and try again. If after 20 minutes 192.168.1.1 is unresponsive you may reboot both PC and router. | ||
tp-link_tl-wr1043nd.1429768653.txt.gz · Last modified: 2015/04/23 05:57 by nworbnhoj
Page Tools
Except where otherwise noted, content on this wiki is licensed under the following license: CC Attribution-Share Alike 4.0 International
