tp-link_tl-wr1043nd
Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision | ||
|
tp-link_tl-wr1043nd [2015/04/23 04:30] nworbnhoj [Introduction] |
tp-link_tl-wr1043nd [2015/04/26 23:59] (current) nworbnhoj old revision restored (2014/02/16 00:50) |
||
|---|---|---|---|
| Line 1: | Line 1: | ||
| - | ====== TP-Link | + | ====== TP-Link |
| < | < | ||
| WARNING: This document may contain errors which may result in damage to your router. USE AT YOUR OWN RISK. | WARNING: This document may contain errors which may result in damage to your router. USE AT YOUR OWN RISK. | ||
| </ | </ | ||
| + | {{INLINETOC 2 4 }} | ||
| ===== Introduction ===== | ===== Introduction ===== | ||
| - | The easiest method to flash TP-Link routers is with the " | ||
| - | If you do run into trouble, then ask a question at the [[http:// | ||
| - | The TP-Link TL-WR1043ND is a very popular Gargoyle router due price and the hardware feature set. | ||
| - | ===== Download firmware ===== | ||
| - | Go to the [[http://www.gargoyle-router.com/download.php | + | The TP-Link TL-WR1043ND is becoming a very popular Gargoyle router due price and hardware feature set. There are many ways of [[http://wiki.openwrt.org/toh/ |
| - | **Download: | + | |
| - | **Architecture: | + | |
| - | **Branch:** 1.6 (stable)\\ | + | |
| - | **Version: | + | |
| - | :!: To __replace__ the original TP-LINK firmware select the **factory.bin** download.\\ | + | //Note: Firmware is still listed as experimental and not all features may work as expected.// |
| + | {{ tplink-wr1043nd.jpg }} | ||
| - | |**TP-WR1043ND-V1.X** | + | ===== Download firmware |
| - | |**TP-WR1043ND-V2.X** | + | Select the correct firmware for this device. |
| - | |**TP-WDR3600-V1.X** | + | |
| - | :!: To __upgrade__ Gargoyle or OpenWRT firmware | + | {{:select.jpg|}} |
| + | Upgrading existing router (Gargoyle or OpenWRT) firmware | ||
| + | '' | ||
| + | Installing new firmware | ||
| + | |||
| + | '' | ||
| ===== Install ===== | ===== Install ===== | ||
| Open the original TP-Link configuration. | Open the original TP-Link configuration. | ||
| - | **Select** //System Tools - Firmware Upgrade//\\ | + | Select |
| - | **Select** //gargoyle_1.6.2-ar71xx-tl-XXXXXXXXX-squashfs-factory.bin//\\ | + | |
| - | **Click** //upgrade// | + | Select |
| + | |||
| + | '' | ||
| + | |||
| + | file then click "upgrade" | ||
| - | :!: If you get the error message | + | If you get the error message |
| |{{: | |{{: | ||
| Line 44: | Line 46: | ||
| Wait about 5 minutes then you should be able to connect to 192.168.1.1 | Wait about 5 minutes then you should be able to connect to 192.168.1.1 | ||
| - | :!: **Do not unplug the power supply during upgrade.** | + | **Do not unplug the power supply during upgrade.** |
| If after 5 minutes 192.168.1.1 is unresponsive first reboot your PC and try again. If after 20 minutes 192.168.1.1 is unresponsive you may reboot both PC and router. | If after 5 minutes 192.168.1.1 is unresponsive first reboot your PC and try again. If after 20 minutes 192.168.1.1 is unresponsive you may reboot both PC and router. | ||
tp-link_tl-wr1043nd.1429763416.txt.gz · Last modified: 2015/04/23 04:30 by nworbnhoj
Page Tools
Except where otherwise noted, content on this wiki is licensed under the following license: CC Attribution-Share Alike 4.0 International
