buffalo_wzr-hp-g300nh
Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision | ||
|
buffalo_wzr-hp-g300nh [2012/01/17 07:43] ispyisail |
buffalo_wzr-hp-g300nh [2015/09/01 21:38] (current) nworbnhoj [Buffalo WZR-HP-G300NH] |
||
|---|---|---|---|
| Line 1: | Line 1: | ||
| - | ====== | + | ======= |
| + | |||
| + | < | ||
| + | WARNING: This document may contain errors which may result in damage to your router. USE AT YOUR OWN RISK. | ||
| + | </ | ||
| < | < | ||
| NOTE: More recent versions of the WZR-HP-G300NH have had a hardware change without bumping the revision number or changing the hardware label. | NOTE: More recent versions of the WZR-HP-G300NH have had a hardware change without bumping the revision number or changing the hardware label. | ||
| - | The newer hardware appears to have the rtl8366rb Ethernet switch while older hardware had the rtl8366s switch. As a result, this newer hardware is NOT supported | + | The newer hardware appears to have the rtl8366rb Ethernet switch while older hardware had the rtl8366s switch. As a result, this newer hardware is **NOT** supported |
| </ | </ | ||
| - | ====== Introduction | + | ===== Introduction ===== |
| Step-by-step instructions for the non technical person who wants to install Gargoyle on a Buffalo WZR-HP-G300NH. | Step-by-step instructions for the non technical person who wants to install Gargoyle on a Buffalo WZR-HP-G300NH. | ||
| - | ====== Requirements | + | ===== Requirements ===== |
| Factory stock Buffalo WZR-HP-G300NH router and upgrading it to Gargoyle | Factory stock Buffalo WZR-HP-G300NH router and upgrading it to Gargoyle | ||
| - | ====== Upgrade to DD-WRT | + | ===== Upgrade to DD-WRT ===== |
| Use the Buffalo setup to switch from the "user friendly" | Use the Buffalo setup to switch from the "user friendly" | ||
| - | ====== Set Password | + | ===== Set Password ===== |
| Logged into DD-WRT at 192.168.11.1 and set a new password and wrote it down. | Logged into DD-WRT at 192.168.11.1 and set a new password and wrote it down. | ||
| - | ====== Telnet | + | ===== Telnet ===== |
| - | ===== Install Telnet | + | ==== Install Telnet ==== |
| Installed Telnet on Windows 7 from control panel. | Installed Telnet on Windows 7 from control panel. | ||
| - | ===== Login with Telent | + | ==== Login with Telent ==== |
| Opened Telnet and entered: | Opened Telnet and entered: | ||
| Line 40: | Line 44: | ||
| After successful login, copied and pasted these commands to telnet | After successful login, copied and pasted these commands to telnet | ||
| - | ===== Upgrade to Gargoyle | + | ==== Upgrade to Gargoyle ==== |
| Line 59: | Line 63: | ||
| Finally, the screen said "lost connection" | Finally, the screen said "lost connection" | ||
| - | ====== Gargoyle | + | ===== Gargoyle ===== |
| Gargoyle changed the default IP address to 192.168.1.1 | Gargoyle changed the default IP address to 192.168.1.1 | ||
buffalo_wzr-hp-g300nh.1326786214.txt.gz · Last modified: 2012/01/17 07:43 by ispyisail
Page Tools
Except where otherwise noted, content on this wiki is licensed under the following license: CC Attribution-Share Alike 4.0 International
