Page 3 of 19
Re: Versions 1.9.0 & 1.8.1
Posted: Wed Nov 11, 2015 12:41 am
by ex1t
Any known 1.8.1 bugs with wr1043ndv2 (currently running stock firmware since I bought it recently)
Re: Versions 1.9.0 & 1.8.1
Posted: Wed Nov 11, 2015 9:02 am
by emukim
emukim wrote:i will continute watching if this kind of problem happen again.
the problem still exist.
later i will turn to use 1.6.2. since 1.8.0 is not available.
or
can anyone provide me 1.8.0 firmware ?
Re: Versions 1.9.0 & 1.8.1
Posted: Wed Nov 11, 2015 1:50 pm
by LHoust
As previously posted within the 1.8.0 Thread, 1.8.1 on my TL-WR941ND v3.6 Wireless Router is also Truncating DHCP Entries. In this case I discovered the last 8 (out of total of 100) "Ethers" Entries had been Truncated (all of "Hosts" Entries were still intact)! This occurred within 2 Days of the upgrade from 1.6.2 to 1.8.1. Changes since the upgrade: MAC Addresses on 2 existing DHCP Entries had been revised.
I have again returned to 1.6.2...
Re: Versions 1.9.0 & 1.8.1
Posted: Thu Nov 12, 2015 4:08 am
by gumball3000
ex1t wrote:Any known 1.8.1 bugs with wr1043ndv2 (currently running stock firmware since I bought it recently)
Except
the one I mentioned on the first page, there are no issues at all.
Re: Versions 1.9.0 & 1.8.1
Posted: Fri Nov 13, 2015 2:19 pm
by emukim
i have found out the issue about happen to my network system.
THE MODEM is not working correctly.
it has critical faults, 5~6 times a day.
Now re-testing version 1.8.1.
Hope it will work fine.
Re: Versions 1.9.0 & 1.8.1
Posted: Fri Nov 13, 2015 4:06 pm
by nworbnhoj
emukim wrote:THE MODERM is not working correctly.
it has critical faults, 5~6 times a day.
Can you provide some more detail about the errors when if you see them again please
Re: Versions 1.9.0 & 1.8.1
Posted: Fri Nov 13, 2015 4:11 pm
by 448
gumball3000 wrote:ex1t wrote:Any known 1.8.1 bugs with wr1043ndv2 (currently running stock firmware since I bought it recently)
Except
the one I mentioned on the first page, there are no issues at all.
Has anyone seen this bug else or was it a single case?
And has anyone seen other problems?
I have the TP-Link WR1043ND rev1.8 with firmware 1.8.0 and all is well, but I want to try to improve the signal Wi fi with 1.8.1 firmware which fixed a hardware modes on wireless N routers.
Re: Versions 1.9.0 & 1.8.1
Posted: Fri Nov 13, 2015 5:22 pm
by Lantis
Factory reset works fine for me.
Re: Versions 1.9.0 & 1.8.1
Posted: Fri Nov 13, 2015 6:05 pm
by n8b
Thanks to everybody here for Gargoyle.
I think found a small bug in 1.8.1 and 1.9.0
TL-WDR4300 flash without preserving settings.
Right after setting password and timezone I change WLAN settings:
Wireless Mode: Access Point (AP)
Operation Mode: N+A
Save
It is now working only in 5 GHz as expected and only the 5 GHz LED is on.
But the page does not reflect the settings.
It shows 'Dual Band' and 2.4GHz SSID + 5GHz SSID
If I then change some other settings and save the page again I get 2.4GHz without asking for it.
Re: Versions 1.9.0 & 1.8.1
Posted: Fri Nov 13, 2015 6:10 pm
by Lantis
n8b wrote:Thanks to everybody here for Gargoyle.
I think found a small bug in 1.8.1 and 1.9.0
TL-WDR4300 flash without preserving settings.
Right after setting password and timezone I change WLAN settings:
Wireless Mode: Access Point (AP)
Operation Mode: N+A
Save
It is now working only in 5 GHz as expected and only the 5 GHz LED is on.
But the page does not reflect the settings.
It shows 'Dual Band' and 2.4GHz SSID + 5GHz SSID
If I then change some other settings and save the page again I get 2.4GHz without asking for it.
Can confirm.