Page 1 of 1
madwifi on x86 with ar5212 minipci card
Posted: Sat Jan 21, 2012 4:16 am
by freakazoid
hello
i download gargoyle from git and compiled a firmware for the x86 branch with madwifi driver for my ar5212 card.....
but since gargoyle is using the very old madwifi branch i get a lot of this error
wifi0: ath_chan_set: Unable to reset channel 6 (2437 MHz) flags 0xd0 'Hardware d idn't respond as expected' (HAL status 3)
Re: madwifi on x86 with ar5212 minipci card
Posted: Mon Jan 30, 2012 4:36 am
by freakazoid
anybody is this project dead already.....
Re: madwifi on x86 with ar5212 minipci card
Posted: Mon Jan 30, 2012 4:54 am
by ispyisail
x86 is not in the supported routers list
http://www.gargoyle-router.com/wiki/dok ... ed_routers
I doubt you will get official support but you never know.......
Re: madwifi on x86 with ar5212 minipci card
Posted: Mon Jan 30, 2012 11:19 am
by Eric
ispyisail: Actually, it is. These are the Alix builds. They're tailored for a specific x86 board which is really small called "Alix" boards, and I tend not to test quite as heavily on this platform (since fewer people own them)... but it is supported.
Re: madwifi on x86 with ar5212 minipci card
Posted: Mon Jan 30, 2012 6:58 pm
by freakazoid
no i build a firmware for x86 generic not alix and it works fine except for the wireless which keepes on giving this error
wifi0: ath_chan_set: Unable to reset channel 6 (2437 MHz) flags 0xd0 'Hardware d idn't respond as expected' (HAL status 3)wifi0: ath_chan_set: Unable to reset channel 6 (2437 MHz) flags 0xd0 'Hardware d idn't respond as expected' (HAL status 3)
i think it is beacuse like openwrt gargoyle to is using the old madwifi....
i tried recently the ddwrt x86 trial build and i must say it is rock solid stable with theire madwifi version is it because the used the newest madwifi version ?????
ath5k is not good for me askeep getting disconnected when i download heavy with ath5k
41.478700] wlan0: authenticate with 00:02:61:47:35:a3 (try 1)
[ 41.481610] wlan0: authenticated
[ 41.609014] wlan0: associate with 00:02:61:47:35:a3 (try 1)
[ 41.634006] wlan0: RX AssocResp from 00:02:61:47:35:a3 (capab=0x431 status=0 aid=1)
[ 41.634025] wlan0: associated
Re: madwifi on x86 with ar5212 minipci card
Posted: Fri Feb 03, 2012 11:14 am
by freakazoid
anybody ?????
Re: madwifi on x86 with ar5212 minipci card
Posted: Fri Feb 03, 2012 11:54 am
by Eric
Please don't cross-post in multiple forums.
Re: madwifi on x86 with ar5212 minipci card
Posted: Fri Feb 03, 2012 12:10 pm
by hnl_dk
freakazoid wrote:anybody ?????
Gargoyle and OpenWRT backfire includes the newest stable version af madwifi.
that is version 0.9.4, I know this is four years old, but it is the stable version. But there is made changes to madwifi from within openwrt.
Re: madwifi on x86 with ar5212 minipci card
Posted: Fri Feb 03, 2012 4:50 pm
by freakazoid
so why do you think i have this error
wifi0: ath_chan_set: Unable to reset channel 6 (2437 MHz) flags 0xd0 'Hardware d idn't respond as expected' (HAL status 3)wifi0: ath_chan_set: Unable to reset channel 6 (2437 MHz) flags 0xd0 'Hardware d idn't respond as expected' (HAL status 3)
is it kernel related then
Re: madwifi on x86 with ar5212 minipci card
Posted: Fri Feb 03, 2012 4:56 pm
by hnl_dk
freakazoid wrote:so why do you think i have this error
wifi0: ath_chan_set: Unable to reset channel 6 (2437 MHz) flags 0xd0 'Hardware d idn't respond as expected' (HAL status 3)wifi0: ath_chan_set: Unable to reset channel 6 (2437 MHz) flags 0xd0 'Hardware d idn't respond as expected' (HAL status 3)
is it kernel related then
Seems to be a problem with OpenWRT 10.03.1
https://dev.openwrt.org/ticket/10656
And there has not yet been found a solution.