Gargoyle Forum

Hello all,
I'm running on wrt1900acs v2 the latest version of Gargoyle 1.13.x_test_builds from lantisproject, the 1Gbps connection works as it should if we disable Bandwidth Monitor!
connection Type PPPoE - IPv6 Type DHCPv6 with Prefix Delegation 1Gbps
IPv6 Type DHCPv6 with Prefix Delegation-On - Ok
Operating Mode Gateway/AP
Schedule Reboot-On,
Web Access Protocol - HTTPS,
SSH (public key)-ok
Port Forwarding - Ok,
USB -Ok
Schedule Reboot - At a Set Time - On


@lantis this version will receive some updates?
Can someone guide me on what I need to do to pass the following security tests on the firewall side, and how can I use DNSSEC on gargoyle?

https://ipv6.chappell-family.com/ipv6tcptest/
https://www.grc.com/x/ne.dll?bh0bkyd2

Could you advise what parts of the test you're failing?

There will not be a 1.15 for your device, you'll need to wait until 1.17

This is the version recommended by you!
https://lantisproject.com/gargoyle_cust ... st_builds/

All the tests below, it seems that with the default setting I don't pass them and I don't know what needs to be done,how can I pass these tests with this version, ?


http://www.dnssec-or-not.com/
https://ipv6.chappell-family.com/ipv6tcptest/
https://www.grc.com/x/ne.dll?bh0bkyd2

please can you add more updates for this version, at the moment I find the best alternative to openwrt and ddwrt which have problems on the wifi side...

I want to report a problem in this version, ipv6 works but today I found it inactive on the wifi side!

If you don’t post your results, how can I advise you? I can run the tests on my end but what if we get different results?

I can’t/won’t do updates for your device as it has been disabled in 22.03 (which 1.15 is based on).
I’m sure they will have fixed it in 23.xx, and then it will be fine. But you’ll hav to wait. That’s an openwrt problem, not me.
https://forum.openwrt.org/t/openwrt-22- ... lantis1008

mvebu: Disable devices using broken mv88e6176 switch. This affects the following devices (See mvebubroken_mv88e6176_switch 174, and #11077 65):
CZ.NIC Turris Omnia
Linksys WRT1200AC
Linksys WRT1900ACS
Linksys WRT1900AC v1
Linksys WRT1900AC v2
Linksys WRT3200ACM
Linksys WRT32X
Linksys WRT3200ACM
SolidRun ClearFog Pro

oliver44 wrote: ↑

Sun Mar 26, 2023 1:55 pm

ipv6 works but today I found it inactive on the wifi side!

If the problem is in the wifi firmware, there won't be any fixes as there is no ongoing firmware development (and hasn't been for at least 3 years) for the chipsets in the Linksys WRT series. There have been some driver fixes but that's all (and those only in the last 2 weeks in the upstream repository - nothing prior to that since April 2020). That said, WRT wifi apparently works well enough for some.

Additionally OpenWrt 19.07 (used by Gargoyle 1.13.x) has been designated as end-of-life by OpenWrt and has had no useful updates since 19.07.10 was released in April 2022.

Therefore if you can't give Lantis any information that would show the problem is in Gargoyle code and enable identification of the issue, you have no prospect of any fix. Given the known issues with wifi in the WRT series, you might be better off disabling it and installing a separate wifi access point...

2 additional IPv6 test sites:
- https://test-ipv6.com
- https://ipv6-test.com (this site checks several optional capabilities so a reasonable score is apparently 18/20)