Page 1 of 2
Bandwidth Monitoring Not Working on new Gargoyle 1.12 WRT32X
Posted: Mon Feb 17, 2020 11:16 pm
by agrohe21
wondering if maybe I am missing something. The internet is working and webmon features are working but /tmp/data/bwmon is empty and web page is empty.
Re: Bandwidth Monitoring Not Working on new Gargoyle 1.12 WRT32X
Posted: Tue Feb 18, 2020 2:50 am
by Lantis
Try /etc/init.d/bwmon_gargoyle restart
Re: Bandwidth Monitoring Not Working on new Gargoyle 1.12 WRT32X
Posted: Tue Feb 18, 2020 6:10 am
by RomanHK
Try one more command to be sure, so the whole procedure should be:
Code: Select all
/etc/init.d/bwmon_gargoyle enable
/etc/init.d/bwmon_gargoyle start
Re: Bandwidth Monitoring Not Working on new Gargoyle 1.12 WRT32X
Posted: Tue Feb 18, 2020 8:51 am
by agrohe21
Tried both of those to no avail. Should I reflash an upgrade? I went from stock firmware to Gargoyle. Everything else is working fine other than this, which is the reason I run Gargoyle.
Re: Bandwidth Monitoring Not Working on new Gargoyle 1.12 WRT32X
Posted: Tue Feb 18, 2020 8:59 am
by RomanHK
1.
Do you use Gragoyle as a gateway (WAN on the Internet, LAN computers)? or as a bridge (switch)?
- but if you use Gargoyle as a bridge or switch, these features will not work.
2.
As an alternative, try resetting the configuration to default and starting from scratch.
Re: Bandwidth Monitoring Not Working on new Gargoyle 1.12 WRT32X
Posted: Tue Feb 18, 2020 9:05 am
by agrohe21
Yes, I use gargoyle as the gateway with the Comcast modem going straight to the internet/wan port on the 32X. That connection is good and fast 300Mb+ speed. I turned off wireless and connected 1 lan port to a switch and the switch to an Orbi 3 node network for wireless.
I did copy ethers and quotas over from my Archer c7 setup. let me try the reset option and start from there to see what happens before I copy over the old files. BTW, I dont copy them, I edit the files and insert the old content into the new file.
Re: Bandwidth Monitoring Not Working on new Gargoyle 1.12 WRT32X
Posted: Tue Feb 18, 2020 9:09 am
by agrohe21
As far as I can tell, resetting the configuration means applying the sysupgrade firmware, correct? there is no other way to reset to factory that I see in 1.12.
Nm found it in backup section.
Re: Bandwidth Monitoring Not Working on new Gargoyle 1.12 WRT32X
Posted: Tue Feb 18, 2020 9:18 am
by RomanHK
agrohe21 wrote:As far as I can tell, resetting the configuration means applying the sysupgrade firmware, correct?
Just press this button
:
Re: Bandwidth Monitoring Not Working on new Gargoyle 1.12 WRT32X
Posted: Tue Feb 18, 2020 9:27 am
by agrohe21
Yeah, found that. Reset and now it is working. Will port over the ethers and other stuff and make sure it is working each time after the copy/edit.
would have liked to know what is wrong but it is working anyway.
Re: Bandwidth Monitoring Not Working on new Gargoyle 1.12 WRT32X
Posted: Tue Feb 18, 2020 9:51 am
by agrohe21
I have now found that when I paste my old hosts into the new file, the bwmon stops working.
I see two lines for gargoyle. One has comment to not touch/remove. the other one seems to have to be the line before it. I had pasted my hosts in between and that seemed to be the issue. hopefully that solves it.