WRT54GL Bricked?

Report problems and success stories with Gargoyle on various hardware platforms.

Moderator: Moderators

petubl
Posts: 3
Joined: Mon Apr 22, 2019 9:00 am

WRT54GL Bricked?

Postby petubl » Tue Apr 23, 2019 3:22 am

Good morning everyone,

I tried to install version 1.6.2 on my WRT54GL and when i tried to set it up as an access point, it was not particularly responsive nor broadcasting a wireless signal, so I thought I would return to DD-WRT. I tried flashing it a couple of times but the flash would not work. Even then, when i was trying to flash it, getting to the GUI interface was difficult, the page would time out, but eventually would connect after a few unsuccessful tries.

Now I cannot get gui access at all. I tried to go into failsafe mode, but while i can ping 192.168.1.1 everything else fails. No telnet connection, no ssh connection (refused) and efforts to flash with TFTP fail as well.

But it is there and something works since I can ping it right?

Any ideas to help this newbie?

Thanks

Lantis
Moderator
Posts: 5204
Joined: Mon Jan 05, 2015 5:33 am
Location: Australia

Re: WRT54GL Bricked?

Postby Lantis » Tue Apr 23, 2019 5:42 am

If you successfully got it to failsafe mode, you must use Telnet, not ssh.
That would be the next thing to try, otherwise you may need to use a serial interface to debrick it.
Routers: Various ar71xx/mvebu/x86-64
http://lantisproject.com/downloads/gargoyle_ispyisail.php for the latest releases

petubl
Posts: 3
Joined: Mon Apr 22, 2019 9:00 am

Re: WRT54GL Bricked?

Postby petubl » Tue Apr 23, 2019 7:38 am

Thanks for the response Lantis - I am not sure if i am in failsafe or not - initially the power led is blinking very fast, then the DMZ led comes on and after quite a bit of time the orange led on the logo comes on... That's when i can ping the machine...

How does the serial interface work? What do i need for this?

Lantis
Moderator
Posts: 5204
Joined: Mon Jan 05, 2015 5:33 am
Location: Australia

Re: WRT54GL Bricked?

Postby Lantis » Tue Apr 23, 2019 9:25 am

During failsafe you should get no other LEDs except a fast blinking system light and possibly a LAN link indicator.
If you're getting anything other than that, the system is in a different state most likely.

The serial port is described here:
https://openwrt.org/toh/linksys/wrt54g#serial_port

Note that due to the age of the device and incompatibility with modern firmwares, the amount of support i (and everyone else probably) can give is very limited. Sorry
Routers: Various ar71xx/mvebu/x86-64
http://lantisproject.com/downloads/gargoyle_ispyisail.php for the latest releases

tapper
Moderator
Posts: 1065
Joined: Sun Oct 13, 2013 5:49 pm
Location: Stoke-on-trent UK

Re: WRT54GL Bricked?

Postby tapper » Tue Apr 23, 2019 1:24 pm

I am sorry but the wrt54gl is so old that it cant run new fermwairs. The best thing you can do is try and get your hands on a new router.
Linksys WRT1900AC V2 Gargoyle 1.11
Linksys WRT3200ACM OpenWrt Snapshot

petubl
Posts: 3
Joined: Mon Apr 22, 2019 9:00 am

Re: WRT54GL Bricked?

Postby petubl » Thu Apr 25, 2019 4:59 am

Thanks very much for all the responses guys.

I think that in the end I will retire this router and move on to something else...


Return to “Hardware / Installation Issues”

Who is online

Users browsing this forum: No registered users and 4 guests