No WebUI after upgrade to 1.10.0
Posted: Fri Aug 24, 2018 2:31 pm
Just upgraded my WZR-HP-G300NH from 1.6.2 to 1.10.0 and initially I was able to connect to the WebUI on 192.168.1.1 using the default password, but then when I set the new password (back to my old one), and then went and restored my settings from my backup, the settings seem to have been applied (since the LAN has now reverted back to 192.168.11.x), but the WebUI won't start. If I scan the ports on 192.168.11.1 port 80 is not running, just ports 22, 53 and 111.
I can connect via SSH on port 22, so I was wondering how to get the WebUI running again.
If it's any help, this is what's running:
EDIT: After Googling around a bit I see that OpenWRT uses uHTTPd to serve the webUI, so I just ran:and the webUI not works (ports 80 and 443 both now running). If I reset the router though, uHTTPd doesn't restart. How can I get it to run on startup like it's supposed to?
EDIT2 It seems as thoughsorts it, so I'll leave this here in case anyone else has the same issue.
I can connect via SSH on port 22, so I was wondering how to get the WebUI running again.
If it's any help, this is what's running:
Code: Select all
root@(none):~# ps ww
PID USER VSZ STAT COMMAND
1 root 1404 S /sbin/procd
2 root 0 SW [kthreadd]
3 root 0 SW [ksoftirqd/0]
4 root 0 SW [kworker/0:0]
5 root 0 SW< [kworker/0:0H]
7 root 0 SW< [khelper]
8 root 0 SW [kworker/u2:1]
60 root 0 SW< [writeback]
61 root 0 SW< [bioset]
65 root 0 SW< [kblockd]
67 root 0 SW [kworker/0:1]
68 root 0 SW [kswapd0]
69 root 0 SW [fsnotify_mark]
257 root 0 SW< [deferwq]
258 root 0 SW [kworker/u2:2]
358 root 0 SWN [jffs2_gcd_mtd5]
418 root 888 S /sbin/ubusd
429 root 768 S /sbin/askfirst /bin/ash --login
471 root 0 SW< [rpciod]
495 root 0 SW< [nfsiod]
752 root 0 SW< [cfg80211]
1058 nobody 1024 S /usr/sbin/portmap
1079 root 1564 S /sbin/netifd
1121 root 1364 S /usr/sbin/ntpd -n -l -S /usr/sbin/ntpd-hotplug -p 0.uk.pool.ntp.org -p 1.uk.pool.ntp.org -p 2.uk.pool.ntp.org
1164 root 1140 S /usr/sbin/dropbear -F -P /var/run/dropbear.1.pid -p 22 -K 300
1389 root 1360 S udhcpc -p /var/run/udhcpc-eth1.pid -s /lib/netifd/dhcp.script -f -t 0 -i eth1 -C
1887 nobody 944 S /usr/sbin/dnsmasq -C /var/etc/dnsmasq.conf -k -x /var/run/dnsmasq/dnsmasq.pid
1907 tor 21368 S tor --User tor --PidFile /var/run/tor.pid --RunAsDaemon 1 --SocksPort 0 --AvoidDiskWrites 1 --Log notice syslog --ControlPort 9051 --DataDirectory /var/tor --TransPort 192.168.11.1:9040 --DNSPort 192.168.11.1:9053 --VirtualAddrNetwork 10.192.0.0/12 --AutomapHostsOnResolve 1 --ClientOnly 1
1964 root 1516 S /usr/bin/ddns_gargoyle -P /etc/ddns_providers.conf -C /etc/ddns_gargoyle.conf -d
3325 root 1368 S /usr/sbin/crond -f -c /etc/crontabs -l 9
3512 root 1208 R /usr/sbin/dropbear -F -P /var/run/dropbear.1.pid -p 22 -K 300
3513 root 1368 S -ash
10107 root 1360 R ps ww
Code: Select all
/etc/init.d/uhttpd start
EDIT2 It seems as though
Code: Select all
/etc/init.d/uhttpd enable