Page 3 of 5
Re: Next bleeding edge testers wanted
Posted: Thu Mar 29, 2018 9:54 am
by labou
I upgraded on Archer C7 v2 with no problem using the factory-us.bin without preserving settings. I haven't run into any problems yet, but I'll post an update on anything that might come up. Thanks!
Re: Next bleeding edge testers wanted
Posted: Thu Mar 29, 2018 3:55 pm
by n8b
Plugin page:
plugin sources are called %n_base, %n_management and so on.
Earlier it was chaos_calmer_base but you moved on
Packages kmod-usb-net-cdc-ether and usb-modeswitch are missing so when I plug in a Huawei E3372 it is not recognized.
When enabling and saving a quota I get iptables error:
Code: Select all
Thu Mar 29 21:25:50 2018 daemon.err insmod: module is already loaded - sch_prio
Thu Mar 29 21:25:50 2018 daemon.err insmod: module is already loaded - sch_tbf
Thu Mar 29 21:25:50 2018 daemon.err insmod: module is already loaded - cls_fw
Thu Mar 29 21:25:50 2018 kern.info kernel: [72137.228158] IMQ driver unloaded successfully.
Thu Mar 29 21:25:50 2018 kern.warn kernel: [72137.263617] imq: unknown parameter 'hook_chains' ignored
Thu Mar 29 21:25:50 2018 kern.warn kernel: [72137.269134] imq: unknown parameter 'hook_tables' ignored
Thu Mar 29 21:25:50 2018 kern.info kernel: [72137.276044] Hooked IMQ after mangle on PREROUTING
Thu Mar 29 21:25:50 2018 kern.info kernel: [72137.280980] Hooked IMQ after nat on POSTROUTING
Thu Mar 29 21:25:50 2018 kern.info kernel: [72137.285668] IMQ driver loaded successfully. (numdevs = 1, numqueues = 1, imq_dev_accurate_stats = 1)
Thu Mar 29 21:25:50 2018 kern.info kernel: [72137.294979] Hooking IMQ before NAT on PREROUTING.
Thu Mar 29 21:25:50 2018 kern.info kernel: [72137.299852] Hooking IMQ after NAT on POSTROUTING.
Thu Mar 29 21:25:50 2018 daemon.err uhttpd[1513]: iptables v1.6.2: unknown option "--todev"
Thu Mar 29 21:25:50 2018 daemon.err uhttpd[1513]: Try `iptables -h' or 'iptables --help' for more information.
Without quota I get 54 / 54 Mbit in speedtest.
With below qouta I get 54 / 2 Mbit in speedtest (Download is not throttled as expected)
Max Upload: Unlimited
Max Download: Unlimited
Max Total Up+Down: 0.1 MBytes
Quota Resets: Every Day
Reset Hour: 00:00
Quota Is Active: Always
When Exceeded: Throttle Bandwith
Upload Limit: 200 kBytes/s
Download Limit: 400 kBytes/s
With same quota on my main router (wrt1200ac on 1.10.X) I get 3.1 / 1.8 Mbit in speedtest. (Both UL and DL are throttled)
Thanks!
Re: Next bleeding edge testers wanted
Posted: Fri Mar 30, 2018 10:09 am
by n8b
Flashed from this build back to latest (20180324) 1.10.X build without issues.
I have re-tested my findings now on 1.10.X:
On 1.10.X I also see the DDNS error right after boot and also these when making changes on Connection | Basic:
daemon.err uhttpd[1489]: uci: Entry not found
daemon.err uhttpd[1489]: uci: Invalid argument
daemon.err uhttpd[1489]: ls: /sys/bus/mdio_bus/drivers/Marvell*/0:*: No such file or directory
So these errors in system log is not unique to this first 1.11.X build.
(Quota, backup and Huawei E3372 works OK in 1.10.X but not in 1.11.X)
Re: Next bleeding edge testers wanted
Posted: Fri Mar 30, 2018 11:15 am
by phgerin
miniupnpd reports wrong external address for bandwidth monitoring (should reports local lan address 192.168.1.1)
Re: Next bleeding edge testers wanted
Posted: Sat Mar 31, 2018 12:36 am
by labou
I'm running into an issue when connected to the 2.4 GHz band on the Archer C7 v2. When connected to it I get regular timeouts when pinging the router (nearly 60/40 reply/timeouts) and my download speeds which are usually around 3.8 MB/s get limited to around 300 kB/s.
Once I switch to the 5 GHz band everything is more or less okay again except every 10 minutes or so I'll lose connection to the router and the internet (although not the wifi). The timeouts will last about 30 seconds then it'll be back to normal. That all seems to happen more often when I'm downloading something.
Here are the log results if it is of any use
https://pastebin.com/0dwbPZ9D
Re: Next bleeding edge testers wanted
Posted: Sat Mar 31, 2018 2:35 am
by Lantis
phgerin wrote:miniupnpd reports wrong external address for bandwidth monitoring (should reports local lan address 192.168.1.1)
Can you please provide more detail? I could not replicate this.
How are you testing it.
Re: Next bleeding edge testers wanted
Posted: Sat Mar 31, 2018 7:03 am
by phgerin
Lantis wrote:phgerin wrote:miniupnpd reports wrong external address for bandwidth monitoring (should reports local lan address 192.168.1.1)
Can you please provide more detail? I could not replicate this.
How are you testing it.
I use Peakhour (
https://peakhourapp.com) software on Mac to monitor my routers.
It used to work with LEDE and previous Gargoyle builds.
But it doesnt work with this build. The software see the router and its external IP address.
Edit: I checked with another software on Windows (networx) and it seems to work.
Re: Next bleeding edge testers wanted
Posted: Sat Mar 31, 2018 10:03 am
by francisuk1989
phgerin wrote:Upgraded wdr3600 from LEDE to Gargoyle using the factory image, did not preserve settings.
Everything is working great for now, testing.
Unable to add snmpd via command line:
root@Gargoyle:~# opkg update
Downloading package list for %n_routing source...
Package list for %n_routing downloaded successfully.
root@Gargoyle:~# opkg install snmpd
ERROR: No package named snmpd found, try updating your package lists
Edit: Thanks once again !
is not in the repos
https://downloads.openwrt.org/snapshots ... /packages/ if you get the time, you could ask here and report any bugs or features
https://bugs.openwrt.org
Also with your wdr3600 do you get the 2.4GHz channels from 1-13 (if your European of course?) seem like v1.10.0 im only getting 1-11
Re: Next bleeding edge testers wanted
Posted: Sat Mar 31, 2018 10:59 am
by phgerin
francisuk1989 wrote:
Also with your wdr3600 do you get the 2.4GHz channels from 1-13 (if your European of course?) seem like v1.10.0 im only getting 1-11
Yes, only channels 1 to 11.
Edit: after turning off and on the Wifi, the router entered a reboot loop.
Re: Next bleeding edge testers wanted
Posted: Sat Mar 31, 2018 11:17 am
by francisuk1989
phgerin wrote:francisuk1989 wrote:
Also with your wdr3600 do you get the 2.4GHz channels from 1-13 (if your European of course?) seem like v1.10.0 im only getting 1-11
Yes, only channels 1 to 11.
@Lantis could we get a fix for this?
As i believe america uses 1-11, and the rest are using 1-13
5GHz band i no idea but from my own ISP modem combo i can see channels 36,40,44,48,52,56,60,64,100,104,108,112,116,132,136,140 @ 20 / 40 / 80MHz