Page 1 of 1
					
				TL-WR941ND - problem with 1.3.9
				Posted: Thu Jan 06, 2011 9:15 am
				by pawelg
				TL-WR941nd v3.3, flashed with gargoyle_1.3.9-ar71xx-tl-wr941nd-v3-squashfs-factory.bin
First boot went OK, but after setup WAN interface as a PPPoE and reboot I wasn't able to access the router from LAN.
Network setup made by gargoyle GUI (relevant part):
config interface eth
    option ifname    eth0
config interface lan
    option ifname    "wlan0"
    option type    bridge
config interface wan
    option ifname    eth0
    option proto    pppoe
The router however has 4 LAN port with interface name "lan1 lan2 lan3 lan4" and 1 WAN port with interface name "wan". With manual change in /etc/config/network to:
config interface lan
    option ifname    "lan1 lan2 lan3 lan4"
config interface wan
    option ifname    wan
    option proto    pppoe
I was able to access the router from LAN (DHCP works fine), but PPPoE session is not established. In gargoyle GUI WAN port is marked as LAN, despite previous setup.
It seems like gargoyle dosen't properly recognize router interfaces. How can I deal with this problem?
BR,
PawelG
 
			
					
				Re: TL-WR941ND - problem with 1.3.9
				Posted: Thu Jan 06, 2011 1:18 pm
				by Eric
				Hmm.. it's screwing up the LAN config.  Maybe there's something odd/different with the initial switch configuration in that router (I don't have this one).  Could you do a fresh install, and then post the default /etc/config/network here?
			 
			
					
				Re: TL-WR941ND - problem with 1.3.9
				Posted: Sat Jan 15, 2011 3:24 pm
				by pawelg
				Sorry for late reply, had to wait for serial cable...
Fresh install 1.3.9:
Code: Select all
root@Gargoyle:/# cat /etc/config/network
config interface loopback
        option ifname   lo
        option proto    static
        option ipaddr   127.0.0.1
        option netmask  255.0.0.0
config interface eth
        option ifname   eth0
        option proto    none
config interface lan
        option ifname   "lan1 lan2 lan3 lan4"
        option type     bridge
        option proto    static
        option ipaddr   192.168.1.1
        option netmask  255.255.255.0
config interface wan
        option ifname   wan
        option proto    dhcp
 
			
					
				Re: TL-WR941ND - problem with 1.3.9
				Posted: Sat Jan 15, 2011 4:00 pm
				by pbix
				Please also show the results of the following commands on your WR941ND.
ifconfig
uci show network
cat /var/state/network
Hopefully we can get to the bottom of this.
			 
			
					
				Re: TL-WR941ND - problem with 1.3.9
				Posted: Sat Jan 15, 2011 6:13 pm
				by pawelg
				ifconfig
Code: Select all
root@Gargoyle:/# ifconfig
br-lan    Link encap:Ethernet  HWaddr D8:5D:4C:C6:D8:94
          inet addr:192.168.1.1  Bcast:192.168.1.255  Mask:255.255.255.0
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:267 errors:0 dropped:0 overruns:0 frame:0
          TX packets:197 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0
          RX bytes:22401 (21.8 KiB)  TX bytes:13203 (12.8 KiB)
eth0      Link encap:Ethernet  HWaddr D8:5D:4C:C6:D8:94
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:367 errors:0 dropped:0 overruns:0 frame:0
          TX packets:91 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:54194 (52.9 KiB)  TX bytes:10376 (10.1 KiB)
          Interrupt:4
lan1      Link encap:Ethernet  HWaddr D8:5D:4C:C6:D8:94
          UP BROADCAST MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0
          RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)
lan2      Link encap:Ethernet  HWaddr D8:5D:4C:C6:D8:94
          UP BROADCAST MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0
          RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)
lan3      Link encap:Ethernet  HWaddr D8:5D:4C:C6:D8:94
          UP BROADCAST MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0
          RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)
lan4      Link encap:Ethernet  HWaddr D8:5D:4C:C6:D8:94
          UP BROADCAST MULTICAST  MTU:1500  Metric:1
          RX packets:367 errors:0 dropped:0 overruns:0 frame:0
          TX packets:90 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0
          RX bytes:47588 (46.4 KiB)  TX bytes:8709 (8.5 KiB)
lo        Link encap:Local Loopback
          inet addr:127.0.0.1  Mask:255.0.0.0
          UP LOOPBACK RUNNING  MTU:16436  Metric:1
          RX packets:81 errors:0 dropped:0 overruns:0 frame:0
          TX packets:81 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0
          RX bytes:5436 (5.3 KiB)  TX bytes:5436 (5.3 KiB)
wan       Link encap:Ethernet  HWaddr D8:5D:4C:C6:D8:94
          UP BROADCAST MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0
          RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)
uci show network
Code: Select all
root@Gargoyle:/# uci show network
network.loopback=interface
network.loopback.ifname=lo
network.loopback.proto=static
network.loopback.ipaddr=127.0.0.1
network.loopback.netmask=255.0.0.0
network.eth=interface
network.eth.ifname=eth0
network.eth.proto=none
network.lan=interface
network.lan.ifname=lan1 lan2 lan3 lan4
network.lan.type=bridge
network.lan.proto=static
network.lan.ipaddr=192.168.1.1
network.lan.netmask=255.255.255.0
network.wan=interface
network.wan.ifname=wan
network.wan.proto=dhcp
cat /var/state/network
Code: Select all
root@Gargoyle:/# cat /var/state/network
network.loopback.device=lo
network.loopback.up=1
network.loopback.connect_time=9
network.eth.device=eth0
network.eth.up=1
network.eth.connect_time=10
network.lan.device=lan1 lan2 lan3 lan4
network.lan.ifname=br-lan
network.lan.up=1
network.lan.connect_time=12
network.wan.device=wan
 
			
					
				Re: TL-WR941ND - problem with 1.3.9
				Posted: Mon Jan 17, 2011 7:58 pm
				by pbix
				Well its not obvious to me what is wrong here and since I do not have the router in question I cannot look into it myself.
Have you seen this problem with v1.3.8?
If you don't know have have the time try it and post the same files that were previously asked for.
			 
			
					
				Re: TL-WR941ND - problem with 1.3.9
				Posted: Wed Jan 19, 2011 5:11 am
				by Eric
				Yeah, that lan configuration is like nothing I've seen before for any other router.  No wonder it's causing problems!
There is no switch configuration, but another "eth" section and then you have the ifname set to the "lan1 lan2 lan3 lan4"  I'm really not sure exactly what's going on here or why the configuration needs to be so completely different for this router.
			 
			
					
				Re: TL-WR941ND - problem with 1.3.9
				Posted: Sun Jan 30, 2011 9:02 am
				by pawelg
				1.3.8 is the same, after fresh install:
cat /etc/config/network
Code: Select all
root@Gargoyle:~# cat /etc/config/network
config interface loopback
        option ifname   lo
        option proto    static
        option ipaddr   127.0.0.1
        option netmask  255.0.0.0
config interface eth
        option ifname   eth0
        option proto    none
config interface lan
        option ifname   "lan1 lan2 lan3 lan4"
        option type     bridge
        option proto    static
        option ipaddr   192.168.1.1
        option netmask  255.255.255.0
config interface wan
        option ifname   wan
        option proto    dhcp
ifconfig
Code: Select all
root@Gargoyle:~# ifconfig
br-lan    Link encap:Ethernet  HWaddr D8:5D:4C:C6:D8:94
          inet addr:192.168.1.1  Bcast:192.168.1.255  Mask:255.255.255.0
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:253 errors:0 dropped:0 overruns:0 frame:0
          TX packets:110 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0
          RX bytes:22949 (22.4 KiB)  TX bytes:12770 (12.4 KiB)
eth0      Link encap:Ethernet  HWaddr D8:5D:4C:C6:D8:94
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:344 errors:0 dropped:0 overruns:0 frame:0
          TX packets:111 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:52724 (51.4 KiB)  TX bytes:14505 (14.1 KiB)
          Interrupt:4
lan1      Link encap:Ethernet  HWaddr D8:5D:4C:C6:D8:94
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:344 errors:0 dropped:0 overruns:0 frame:0
          TX packets:110 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0
          RX bytes:46532 (45.4 KiB)  TX bytes:12770 (12.4 KiB)
lan2      Link encap:Ethernet  HWaddr D8:5D:4C:C6:D8:94
          UP BROADCAST MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0
          RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)
lan3      Link encap:Ethernet  HWaddr D8:5D:4C:C6:D8:94
          UP BROADCAST MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0
          RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)
lan4      Link encap:Ethernet  HWaddr D8:5D:4C:C6:D8:94
          UP BROADCAST MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0
          RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)
lo        Link encap:Local Loopback
          inet addr:127.0.0.1  Mask:255.0.0.0
          UP LOOPBACK RUNNING  MTU:16436  Metric:1
          RX packets:12 errors:0 dropped:0 overruns:0 frame:0
          TX packets:12 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0
          RX bytes:744 (744.0 B)  TX bytes:744 (744.0 B)
wan       Link encap:Ethernet  HWaddr D8:5D:4C:C6:D8:94
          UP BROADCAST MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0
          RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)
uci show network
Code: Select all
root@Gargoyle:~# uci show network
network.loopback=interface
network.loopback.ifname=lo
network.loopback.proto=static
network.loopback.ipaddr=127.0.0.1
network.loopback.netmask=255.0.0.0
network.eth=interface
network.eth.ifname=eth0
network.eth.proto=none
network.lan=interface
network.lan.ifname=lan1 lan2 lan3 lan4
network.lan.type=bridge
network.lan.proto=static
network.lan.ipaddr=192.168.1.1
network.lan.netmask=255.255.255.0
network.wan=interface
network.wan.ifname=wan
network.wan.proto=dhcp
cat /var/state/network
Code: Select all
root@Gargoyle:~# cat /var/state/network
network.loopback.device=lo
network.loopback.up=1
network.eth.device=eth0
network.eth.up=1
network.lan.device=lan1 lan2 lan3 lan4
network.lan.ifname=br-lan
network.lan.up=1
network.wan.device=wan