Gargoyle Forum

A forum to discuss the Gargoyle web interface for Openwrt
https://www.gargoyle-router.com/phpbb/

Help with testing the AP+Client Bug

https://www.gargoyle-router.com/phpbb/viewtopic.php?t=206

Page 6 of 9

Re: Help with testing the AP+Client Bug

Posted: Fri Aug 07, 2009 3:31 pm
by DoesItMatter
I loaded up Build 15409 - last build listed on the 'shotgun' trials

Uptime 15+ hours - seems to be working fine on my Fonera 2201+

Any other set of builds that we can try?

Re: Help with testing the AP+Client Bug

Posted: Sat Aug 08, 2009 4:40 pm
by ispyisail
I also have loaded up Build 15409

Router still has troubles until reboot

After reboot router works well

Re: Help with testing the AP+Client Bug

Posted: Sun Aug 09, 2009 8:46 pm
by Eric
That's odd... 15409 should be identical to 15464, which you reported did not work (though it did work for me), though we all agreed 15465 failed. There are no changes between 15409 and 15464, in madwifi, hostapd or wpa_supplicant.

I rebuilt both 15464 and 15465, in case somehow there was some weird problem last time. It would be helpful if you could test these revisions (with the new builds, listed below). After uploading I verified the md5 sums just to be sure of their integrity, so these should be ok.

While most have my time lately has been spent working on improvements to the bandwidth monitor I spent some time going through the actual changes in the madwifi package over this series of revisions. The most suspicious one is actually the first revision on the list, r13761. The modifications made in this revision are expanded upon in 15465, so this may explain why it suddenly gets so much worse at 15465 - it may be there's a minor error in 13761 and 15465 makes it a lot worse.

Ispyisail: since you're reporting the failure before rebooting, can you 1) check if this error is present at 13761 and then 2) check if it happens in 13708? If 13708 works and you see the reboot failure at 13761 we can confirm where the first error like what we're worried about, and this would make a lot of sense based on the nature of the patch.

15464:
gargoyle_1.0.2_m15464-atheros-root.squashfs

gargoyle_1.0.2_m15464-atheros-vmlinux.lzma

gargoyle_1.0.2_m15464-atheros-vmlinux.gz

15465:
gargoyle_1.0.2_m15465-atheros-root.squashfs

gargoyle_1.0.2_m15465-atheros-vmlinux.lzma

gargoyle_1.0.2_m15465-atheros-vmlinux.gz

Re: Help with testing the AP+Client Bug

Posted: Mon Aug 10, 2009 12:42 am
by DoesItMatter
OK.

I reloaded the 15464 from the post above.

This time, I have 4+ hours uptime.

Did NOT need to reboot in order to get it to work, flashed 15464,
and then when interface came up, was able to scan and setup the
network, no reboot needed in order to keep it up and running.

Not sure why I had in issue before with prior 15464, but this one
seems to be working fine currently.

I'll leave it running overnight and verify if still working in the AM.

Re: Help with testing the AP+Client Bug

Posted: Mon Aug 10, 2009 2:35 am
by ispyisail
Ispyisail: since you're reporting the failure before rebooting, can you 1) check if this error is present at 13761 and then 2) check if it happens in 13708? If 13708 works and you see the reboot failure at 13761 we can confirm where the first error like what we're worried about, and this would make a lot of sense based on the nature of the patch.
13761 work perfect, no reboot required

Re: Help with testing the AP+Client Bug

Posted: Mon Aug 10, 2009 3:31 am
by ispyisail
13794 fail

This is the serial output

Code: Select all

^C
RedBoot> fin init -f
** Error: Illegal command: "fin"
RedBoot> fis init -f
About to initialize [format] FLASH image system - continue (y/n)? y
*** Initialize FLASH Image System
... Erase from 0xa8030000-0xa87d0000: ..........................................................................................................................
... Erase from 0xa87d0000-0xa87e0000: .
... Program from 0x80ff0000-0x81000000 at 0xa87d0000: .
RedBoot> ÿ+Ethernet eth0: MAC address 00:18:0a:01:8e:2c
IP: 192.168.84.1/255.255.255.0, Gateway: 0.0.0.0
Default server: 192.168.84.2

RedBoot(tm) bootstrap and debug environment [ROMRAM]
Release, version V1.04 - built 12:24:00, Apr 17 2006

Copyright (C) 2000, 2001, 2002, 2003, 2004 Red Hat, Inc.

Board: Meraki Mini
RAM: 0x80000000-0x82000000, [0x8003d110-0x80fe1000] available
FLASH: 0xa8000000 - 0xa87e0000, 128 blocks of 0x00010000 bytes each.
== Executing boot script in 10.000 seconds - enter ^C to abort
+Ethernet eth0: MAC address 00:18:0a:01:8e:2c
IP: 192.168.84.1/255.255.255.0, Gateway: 0.0.0.0
Default server: 192.168.84.2

RedBoot(tm) bootstrap and debug environment [ROMRAM]
Release, version V1.04 - built 12:24:00, Apr 17 2006

Copyright (C) 2000, 2001, 2002, 2003, 2004 Red Hat, Inc.

Board: Meraki Mini
RAM: 0x80000000-0x82000000, [0x8003d110-0x80fe1000] available
FLASH: 0xa8000000 - 0xa87e0000, 128 blocks of 0x00010000 bytes each.
== Executing boot script in 10.000 seconds - enter ^C to abort
RedBoot> fis load -d vmlinux.bin.l7
Image loaded from 0x80041000-0x80275085
RedBoot> exec
Now booting linux kernel:
 Base address 0x80030000 Entry 0x80041000
 Cmdline :
Linux version 2.6.26.8 (eric@Osiris) (gcc version 4.1.2) #1 Sun Aug 2 15:31:49 EDT 2009
CPU revision is: 00019064 (MIPS 4KEc)
Determined physical RAM map:
 memory: 02000000 @ 00000000 (usable)
Initrd not found or empty - disabling initrd
Zone PFN ranges:
  Normal          0 ->     8192
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
    0:        0 ->     8192
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 8128
Kernel command line: console=ttyS0,9600 rootfstype=squashfs,jffs2 init=/etc/preinit
Primary instruction cache 16kB, VIPT, 4-way, linesize 16 bytes.
Primary data cache 16kB, 4-way, VIPT, no aliases, linesize 16 bytes
PID hash table entries: 128 (order: 7, 512 bytes)
console [ttyS0] enabled
Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
Memory: 29860k/32768k available (1835k kernel code, 2908k reserved, 299k data, 124k init, 0k highmem)
SLUB: Genslabs=6, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
Mount-cache hash table entries: 512
net_namespace: 484 bytes
NET: Registered protocol family 16
Radio config found at offset 0x10000(0x100)
AR531x PCI init...
done
PCI: fixing up device 0,3,0
PCI: Failed to allocate mem resource #1:4000000@84000000 for 0000:00:00.0
PCI: Failed to allocate mem resource #1:4000000@84000000 for 0000:00:03.0
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 1024 (order: 1, 8192 bytes)
TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
TCP: Hash tables configured (established 1024 bind 1024)
TCP reno registered
NET: Registered protocol family 1
ar531x: Registering GPIODEV device
squashfs: version 3.0 (2006/03/15) Phillip Lougher
Registering mini_fo version $Id$
JFFS2 version 2.2. (NAND) (SUMMARY)  © 2001-2006 Red Hat, Inc.
msgmni has been set to 58
io scheduler noop registered
io scheduler deadline registered (default)
gpiodev: gpio device registered with major 254
gpiodev: gpio platform device registered with access mask FFFFFFFF
Serial: 8250/16550 driver $Revision: 1.90 $ 1 ports, IRQ sharing disabled
serial8250: ttyS0 at MMIO 0xb1100003 (irq = 37) is a 16550A
eth0: Atheros AR231x: 00:18:0a:01:8e:2c, irq 4
ar2313_eth_mii: probed
eth0: attached PHY driver [Generic PHY] (mii_bus:phy_addr=0:01)
cmdlinepart partition parsing not available
Searching for RedBoot partition table in spiflash at offset 0x7d0000
6 RedBoot partitions found on MTD device spiflash
Creating 6 MTD partitions on "spiflash":
0x00000000-0x00030000 : "RedBoot"
0x00030000-0x006d0000 : "rootfs"
mtd: partition "rootfs" set to be root filesystem
mtd: partition "rootfs_data" created automatically, ofs=2B0000, len=420000
0x002b0000-0x006d0000 : "rootfs_data"
0x006d0000-0x007d0000 : "vmlinux.bin.l7"
0x007d0000-0x007df000 : "FIS directory"
0x007df000-0x007e0000 : "RedBoot config"
0x007e0000-0x00800000 : "boardconfig"
Registered led device: gpio1
Registered led device: gpio2
Registered led device: gpio3
Registered led device: gpio4
Registered led device: wlan
TCP vegas registered
NET: Registered protocol family 17
Bridge firewalling registered
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
VFS: Mounted root (squashfs filesystem) readonly.
eth0: Configuring MAC for full duplex
Freeing unused kernel memory: 124k freed
Please be patient, while OpenWrt loads ...
Algorithmics/MIPS FPU Emulator v1.5
- preinit -
Press CTRL-C for failsafe
jffs2 not ready yet; using ramdisk
mini_fo: using base directory: /
mini_fo: using storage directory: /tmp/root
- init -

Please press Enter to activate this console. device eth0 entered promiscuous mode
br-lan: port 1(eth0) entering learning state
br-lan: topology change detected, propagating
br-lan: port 1(eth0) entering forwarding state
br-lan: port 1(eth0) entering disabled state
PPP generic driver version 2.4.2
br-lan: port 1(eth0) entering learning state
br-lan: topology change detected, propagating
br-lan: port 1(eth0) entering forwarding state
ip_tables: (C) 2000-2006 Netfilter Core Team
nf_conntrack version 0.5.0 (1024 buckets, 4096 max)
IPP2P v0.8.1_rc1 loading
IMQ driver loaded successfully.
        Hooking IMQ before NAT on PREROUTING.
        Hooking IMQ after NAT on POSTROUTING.
Ebtables v2.0 registered
wlan: trunk
ath_hal: module license 'Proprietary' taints kernel.
ath_hal: 2008-10-02 (AR5212, AR5312, RF5111, RF5112, RF2316, RF2317, REGOPS_FUNC, TX_DESC_SWAP, DFS, XR)
ath_rate_minstrel: Minstrel automatic rate control algorithm 1.2 (trunk)
ath_rate_minstrel: look around rate set to 10%
ath_rate_minstrel: EWMA rolloff level set to 75%
ath_rate_minstrel: max segment size in the mrr set to 6000 us
wlan: mac acl policy registered
ath_ahb: trunk
Atheros HAL provided by OpenWrt, DD-WRT and MakSat Technologies
wifi0: 11b rates: 1Mbps 2Mbps 5.5Mbps 11Mbps
wifi0: 11g rates: 1Mbps 2Mbps 5.5Mbps 11Mbps 6Mbps 9Mbps 12Mbps 18Mbps 24Mbps 36Mbps 48Mbps 54Mbps
wifi0: turboG rates: 6Mbps 12Mbps 18Mbps 24Mbps 36Mbps 48Mbps 54Mbps
wifi0: H/W encryption support: WEP AES AES_CCM TKIP
ath_ahb: wifi0: Atheros 2315 WiSoC: mem=0xb0000000, irq=3
jffs2_scan_eraseblock(): End of filesystem marker found at 0x0
jffs2_build_filesystem(): unlocking the mtd device... done.
jffs2_build_filesystem(): erasing all blocks after the end marker... done.
Data CRC d30e587e != calculated CRC 0bd411f5 for node at 00400810
Kernel bug detected[#1]:
Cpu 0
$ 0   : 00000000 10009c00 00000001 81e28400
$ 4   : 81fcfa00 00000000 00000000 00001000
$ 8   : 00aa0000 8158b458 9ee1199e 5e9f7f02
$12   : fec7297e 00000458 8027c988 7e2fed1f
$16   : 00000458 818e38b0 8102b160 00001000
$20   : 00000000 00001000 00000000 81f9f600
$24   : 00000000 80172a28
$28   : 81fe0000 81fe1cb8 00000458 8008f91c
Hi    : 00989663
Lo    : ec46a080
epc   : 80113168     Tainted: P
ra    : 8008f91c Status: 10009c03    KERNEL EXL IE
Cause : 10800034
PrId  : 00019064 (MIPS 4KEc)
Modules linked in: ath_ahb wlan_xauth wlan_wep wlan_tkip wlan_ccmp wlan_acl ath_rate_minstrel ath_hal(P) wlan_scan_sta wlan_scan_ap wlan ebt_vlan ebt_ulog ebt_stp ebt_snat ebt_redirect ebt_pkttype ebt_nflog ebt_mark_m ebt_mark ebt_log ebt_limit ebt_ip ebt_dnat ebt_arpreply ebt_arpnat ebt_arp ebt_among ebt_802_3 ebtable_nat ebtable_filter ebtable_broute ebtables ipt_weburl ipt_timerange nf_nat_tftp nf_conntrack_tftp nf_nat_irc nf_conntrack_irc nf_nat_ftp nf_conntrack_ftp xt_iprange ipt_TTL xt_MARK ipt_ECN xt_CLASSIFY ipt_ttl xt_time xt_tcpmss xt_statistic xt_mark xt_length ipt_ecn xt_DSCP xt_dscp ipt_IMQ imq xt_string xt_layer7 ipt_ipp2p ipt_bandwidth ipt_REDIRECT ipt_NETMAP ipt_MASQUERADE iptable_nat nf_nat xt_CONNMARK ipt_recent xt_helper xt_conntrack xt_connmark xt_connbytes xt_state nf_conntrack_ipv4 nf_conntrack ipt_REJECT xt_TCPMSS ipt_LOG xt_multiport xt_mac xt_limit iptable_mangle iptable_filter ip_tables xt_tcpudp x_tables ppp_async ppp_generic slhc crc_ccitt
Process cp (pid: 1183, threadinfo=81fe0000, task=81e315b8, tls=00000000)
Stack : 81fe1db4 81c77900 00000002 00000028 00000000 00001000 81fe1cd8 81e315e0
        00000000 8005e244 00000458 00001000 00000000 00001000 00000458 81fe1d30
        00000000 818e3948 00000000 8008f91c 81f9f600 0000000d 00000000 004007d8
        00000458 00000458 8102b160 81fe1e88 8102b160 81fe1e88 81fe1e58 00000001
        00000000 00000458 173cdac3 0000000d 000000b3 80215a64 00000000 818e38b0
        ...
Call Trace:[<8005e244>][<8008f91c>][<80090328>][<801153a8>][<80090424>][<800b6940>][<800780b4>][<800baaec>][<800b7258>][<800b7914>][<800b48fc>][<8004a370>]

Code: 10a00001  afa00020  2ca20001 <00028036> 24021000  13c20002  00009821  32d30ffc  0c04522a
mini_fo: using base directory: /
mini_fo: using storage directory: /jffs
ath_rate_minstrel: no rates for 00:18:0a:01:8e:2c?
br-lan: port 1(eth0) entering disabled state
device eth0 left promiscuous mode
br-lan: port 1(eth0) entering disabled state
device eth0 entered promiscuous mode
br-lan: port 1(eth0) entering learning state
br-lan: topology change detected, propagating
br-lan: port 1(eth0) entering forwarding state
br-lan: port 1(eth0) entering disabled state
br-lan: port 1(eth0) entering learning state
br-lan: topology change detected, propagating
br-lan: port 1(eth0) entering forwarding state

Re: Help with testing the AP+Client Bug

Posted: Mon Aug 10, 2009 3:32 am
by ispyisail
This is the serial output after reboot

Code: Select all

+Ethernet eth0: MAC address 00:18:0a:01:8e:2c
IP: 192.168.84.1/255.255.255.0, Gateway: 0.0.0.0
Default server: 192.168.84.2

RedBoot(tm) bootstrap and debug environment [ROMRAM]
Release, version V1.04 - built 12:24:00, Apr 17 2006

Copyright (C) 2000, 2001, 2002, 2003, 2004 Red Hat, Inc.

Board: Meraki Mini
RAM: 0x80000000-0x82000000, [0x8003d110-0x80fe1000] available
FLASH: 0xa8000000 - 0xa87e0000, 128 blocks of 0x00010000 bytes each.
== Executing boot script in 10.000 seconds - enter ^C to abort
RedBoot> fis load -d vmlinux.bin.l7
Image loaded from 0x80041000-0x80275085
RedBoot> exec
Now booting linux kernel:
 Base address 0x80030000 Entry 0x80041000
 Cmdline :
Linux version 2.6.26.8 (eric@Osiris) (gcc version 4.1.2) #1 Sun Aug 2 15:31:49 EDT 2009
CPU revision is: 00019064 (MIPS 4KEc)
Determined physical RAM map:
 memory: 02000000 @ 00000000 (usable)
Initrd not found or empty - disabling initrd
Zone PFN ranges:
  Normal          0 ->     8192
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
    0:        0 ->     8192
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 8128
Kernel command line: console=ttyS0,9600 rootfstype=squashfs,jffs2 init=/etc/preinit
Primary instruction cache 16kB, VIPT, 4-way, linesize 16 bytes.
Primary data cache 16kB, 4-way, VIPT, no aliases, linesize 16 bytes
PID hash table entries: 128 (order: 7, 512 bytes)
console [ttyS0] enabled
Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
Memory: 29860k/32768k available (1835k kernel code, 2908k reserved, 299k data, 124k init, 0k highmem)
SLUB: Genslabs=6, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
Mount-cache hash table entries: 512
net_namespace: 484 bytes
NET: Registered protocol family 16
Radio config found at offset 0x10000(0x100)
AR531x PCI init...
done
PCI: fixing up device 0,3,0
PCI: Failed to allocate mem resource #1:4000000@84000000 for 0000:00:00.0
PCI: Failed to allocate mem resource #1:4000000@84000000 for 0000:00:03.0
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 1024 (order: 1, 8192 bytes)
TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
TCP: Hash tables configured (established 1024 bind 1024)
TCP reno registered
NET: Registered protocol family 1
ar531x: Registering GPIODEV device
squashfs: version 3.0 (2006/03/15) Phillip Lougher
Registering mini_fo version $Id$
JFFS2 version 2.2. (NAND) (SUMMARY)  © 2001-2006 Red Hat, Inc.
msgmni has been set to 58
io scheduler noop registered
io scheduler deadline registered (default)
gpiodev: gpio device registered with major 254
gpiodev: gpio platform device registered with access mask FFFFFFFF
Serial: 8250/16550 driver $Revision: 1.90 $ 1 ports, IRQ sharing disabled
serial8250: ttyS0 at MMIO 0xb1100003 (irq = 37) is a 16550A
eth0: Atheros AR231x: 00:18:0a:01:8e:2c, irq 4
ar2313_eth_mii: probed
eth0: attached PHY driver [Generic PHY] (mii_bus:phy_addr=0:01)
cmdlinepart partition parsing not available
Searching for RedBoot partition table in spiflash at offset 0x7d0000
6 RedBoot partitions found on MTD device spiflash
Creating 6 MTD partitions on "spiflash":
0x00000000-0x00030000 : "RedBoot"
0x00030000-0x006d0000 : "rootfs"
mtd: partition "rootfs" set to be root filesystem
mtd: partition "rootfs_data" created automatically, ofs=2B0000, len=420000
0x002b0000-0x006d0000 : "rootfs_data"
0x006d0000-0x007d0000 : "vmlinux.bin.l7"
0x007d0000-0x007df000 : "FIS directory"
0x007df000-0x007e0000 : "RedBoot config"
0x007e0000-0x00800000 : "boardconfig"
Registered led device: gpio1
Registered led device: gpio2
Registered led device: gpio3
Registered led device: gpio4
Registered led device: wlan
TCP vegas registered
NET: Registered protocol family 17
Bridge firewalling registered
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
VFS: Mounted root (squashfs filesystem) readonly.
eth0: Configuring MAC for full duplex
Freeing unused kernel memory: 124k freed
Please be patient, while OpenWrt loads ...
Algorithmics/MIPS FPU Emulator v1.5
- preinit -
Press CTRL-C for failsafe
switching to jffs2
mini_fo: using base directory: /
mini_fo: using storage directory: /jffs
- init -

Please press Enter to activate this console. device eth0 entered promiscuous mode
br-lan: port 1(eth0) entering learning state
br-lan: topology change detected, propagating
br-lan: port 1(eth0) entering forwarding state
PPP generic driver version 2.4.2
br-lan: port 1(eth0) entering disabled state
br-lan: port 1(eth0) entering learning state
br-lan: topology change detected, propagating
br-lan: port 1(eth0) entering forwarding state
ip_tables: (C) 2000-2006 Netfilter Core Team
nf_conntrack version 0.5.0 (1024 buckets, 4096 max)
IPP2P v0.8.1_rc1 loading
IMQ driver loaded successfully.
        Hooking IMQ before NAT on PREROUTING.
        Hooking IMQ after NAT on POSTROUTING.
Ebtables v2.0 registered
wlan: trunk
ath_hal: module license 'Proprietary' taints kernel.
ath_hal: 2008-10-02 (AR5212, AR5312, RF5111, RF5112, RF2316, RF2317, REGOPS_FUNC, TX_DESC_SWAP, DFS, XR)
ath_rate_minstrel: Minstrel automatic rate control algorithm 1.2 (trunk)
ath_rate_minstrel: look around rate set to 10%
ath_rate_minstrel: EWMA rolloff level set to 75%
ath_rate_minstrel: max segment size in the mrr set to 6000 us
wlan: mac acl policy registered
ath_ahb: trunk
Atheros HAL provided by OpenWrt, DD-WRT and MakSat Technologies
wifi0: 11b rates: 1Mbps 2Mbps 5.5Mbps 11Mbps
wifi0: 11g rates: 1Mbps 2Mbps 5.5Mbps 11Mbps 6Mbps 9Mbps 12Mbps 18Mbps 24Mbps 36Mbps 48Mbps 54Mbps
wifi0: turboG rates: 6Mbps 12Mbps 18Mbps 24Mbps 36Mbps 48Mbps 54Mbps
wifi0: H/W encryption support: WEP AES AES_CCM TKIP
ath_ahb: wifi0: Atheros 2315 WiSoC: mem=0xb0000000, irq=3



BusyBox v1.11.2 (2009-08-02 15:18:06 EDT) built-in shell (ash)
Enter 'help' for a list of built-in commands.

  _______                     ________        __
 |       |.-----.-----.-----.|  |  |  |.----.|  |_
 |   -   ||  _  |  -__|     ||  |  |  ||   _||   _|
 |_______||   __|_____|__|__||________||__|  |____|
          |__| W I R E L E S S   F R E E D O M
 KAMIKAZE (8.09.1, unknown) ----------------------------
  * 10 oz Vodka       Shake well with ice and strain
  * 10 oz Triple sec  mixture into 10 shot glasses.
  * 10 oz lime juice  Salute!
 ---------------------------------------------------
root@OpenWrt:/#

Re: Help with testing the AP+Client Bug

Posted: Mon Aug 10, 2009 3:36 am
by ispyisail
As per usual router works after reboot

serial output showing changes

I hope all this helps

Code: Select all

root@OpenWrt:/# ath_rate_minstrel: no rates for 00:18:0a:01:8e:2c?
br-lan: port 1(eth0) entering disabled state
device eth0 left promiscuous mode
br-lan: port 1(eth0) entering disabled state
device eth0 entered promiscuous mode
br-lan: port 1(eth0) entering learning state
br-lan: topology change detected, propagating
br-lan: port 1(eth0) entering forwarding state
br-lan: port 1(eth0) entering disabled state
br-lan: port 1(eth0) entering learning state
br-lan: topology change detected, propagating
br-lan: port 1(eth0) entering forwarding state
device ath0 entered promiscuous mode
br-lan: port 2(ath0) entering learning state
br-lan: topology change detected, propagating
br-lan: port 2(ath0) entering forwarding state
device ath1 entered promiscuous mode
br-wan: port 1(ath1) entering learning state
br-wan: topology change detected, propagating
br-wan: port 1(ath1) entering forwarding state
br-wan: port 1(ath1) entering disabled state
br-wan: port 1(ath1) entering learning state
br-wan: topology change detected, propagating
br-wan: port 1(ath1) entering forwarding state
------------[ cut here ]------------
WARNING: at kernel/softirq.c:141 ()
Modules linked in: ath_ahb wlan_xauth wlan_wep wlan_tkip wlan_ccmp wlan_acl ath_rate_minstrel ath_hal(P) wlan_scan_sta wlan_scan_ap wlan ebt_vlan ebt_ulog ebt_stp ebt_snat ebt_redirect ebt_pkttype ebt_nflog ebt_mark_m ebt_mark ebt_log ebt_limit ebt_ip ebt_dnat ebt_arpreply ebt_arpnat ebt_arp ebt_among ebt_802_3 ebtable_nat ebtable_filter ebtable_broute ebtables ipt_weburl ipt_timerange nf_nat_tftp nf_conntrack_tftp nf_nat_irc nf_conntrack_irc nf_nat_ftp nf_conntrack_ftp xt_iprange ipt_TTL xt_MARK ipt_ECN xt_CLASSIFY ipt_ttl xt_time xt_tcpmss xt_statistic xt_mark xt_length ipt_ecn xt_DSCP xt_dscp ipt_IMQ imq xt_string xt_layer7 ipt_ipp2p ipt_bandwidth ipt_REDIRECT ipt_NETMAP ipt_MASQUERADE iptable_nat nf_nat xt_CONNMARK ipt_recent xt_helper xt_conntrack xt_connmark xt_connbytes xt_state nf_conntrack_ipv4 nf_conntrack ipt_REJECT xt_TCPMSS ipt_LOG xt_multiport xt_mac xt_limit iptable_mangle iptable_filter ip_tables xt_tcpudp x_tables ppp_async ppp_generic slhc crc_ccitt
Call Trace:[<80048a68>][<80048a68>][<8006155c>][<c026bbdc>][<c026bb94>][<c0284740>][<80089e00>][<8008b32c>][<801a247c>][<800676e0>][<80193b7c>][<c028c8c4>][<c028cd6c>][<80188048>][<c02825e0>][<80189b18>][<8013c660>][<c0283ea0>][<80189b18>][<c0284350>][<c026cfc0>][<80192db4>][<80089e00>][<8006be10>][<80067328>][<80067328>][<80045240>][<8006740c>][<800432e4>][<80077b90>][<80042dd4>][<800452c0>][<80042dd8>]
---[ end trace 2dd980ee6a4be9e3 ]---

Re: Help with testing the AP+Client Bug

Posted: Mon Aug 10, 2009 3:42 am
by ispyisail
Back to ROBIN to do similar flashing and testing

I always us

Code: Select all

fis init -f
with the amount of flashing im doing it would same me time if you could add this into "fon flash"

Re: Help with testing the AP+Client Bug

Posted: Mon Aug 10, 2009 3:03 pm
by DoesItMatter
OK. Did more testing with build 15464 - that one is working, has an
uptime of 12+ hours.

Did an fis init -f again and wiped and re-installed build 15465

That version crashed and failed in less than 5 minutes.

There is something very wrong, and there is a driver issue somewhere.

http://www.xirrus.com/library/wifitools.php

You can get a free wi-fi monitor and inspector there.

I've been checking each build, and all the builds EXCEPT build 15465
report the Fonera as a FON device.

When I load build 15465 - the Fon device is listed as
Allied Telesyn Internaion

I suspect someone tried to put in a different driver or maybe
replaced it with the wrong driver?

15464 = Working and 15465 = NOT working

Here are some screenshots below.
All times are UTC-04:00
Page 6 of 9

Powered by phpBB® Forum Software © phpBB Limited