Gargoyle Forum

Should be fine. It's similar to the other EA models that were asked for in the previous post. The only thing that concerns me is you seem to need 3 files to flash each device. I'm unfamiliar with this so I'm just a bit wary on generating the images.

I'll give them all a go soon.

Lantis wrote:Should be fine. It's similar to the other EA models that were asked for in the previous post. The only thing that concerns me is you seem to need 3 files to flash each device. I'm unfamiliar with this so I'm just a bit wary on generating the images.

I'll give them all a go soon.

Top man! I will find one off ebay then. It will give me some thing to play with.

Router Model: Asus RT-N12
Link to Openwrt wiki: https://wiki.openwrt.org/toh/asus/rt-n12
Is it supported in Openwrt? Yes
Does it have >= 4MB of flash? Yes
Does it have >= 8MB of flash? No
Does it have USB support? No


Notes from Lantis:
Rejected - 4MB

Router Model: Asus RT-N13U H/W Rev. B1
Link to Openwrt wiki: https://wiki.openwrt.org/toh/asus/rt-n13u
Is it supported in Openwrt? Yes
Does it have >= 4MB of flash? Yes
Does it have >= 8MB of flash? Yes
Does it have USB support? Yes


Notes from Lantis:
Accepted

Router Model: Linksys WRV54G
Link to Openwrt wiki: https://wiki.openwrt.org/toh/linksys/wrv54g
Is it supported in Openwrt? Yes
Does it have >= 4MB of flash? Yes
Does it have >= 8MB of flash? Yes
Does it have USB support? No


Notes from Lantis:
Rejected - Sloooooooooooooow (266MHz)

dlogictech wrote:Router Model: Linksys WRV54G
Link to Openwrt wiki: https://wiki.openwrt.org/toh/linksys/wrv54g
Is it supported in Openwrt? Yes
Does it have >= 4MB of flash? Yes
Does it have >= 8MB of flash? Yes
Does it have USB support? No

Hi there mate due to the slow CPU i dont think Gargoyle will run verry well for this router. I had a wrt54g overclocked to 333 MHZ and it was frustratingly slow and crashed a lot.

Lantis wrote:Should be fine. It's similar to the other EA models that were asked for in the previous post. The only thing that concerns me is you seem to need 3 files to flash each device. I'm unfamiliar with this so I'm just a bit wary on generating the images.

I'll give them all a go soon.

As of r47458 the E4200v2 and EA4500 are completely supported. These boards are identified by the codename "Viper."
Build with:

Target System → "Marvell Kirkwood"

Target Profile → "Generic" or "Linksys E4200v2 / EA4500 (Viper)"

Target Images → squashfs
This will produce the images:
openwrt-kirkwood-linksys-viper-squashfs-factory.bin
openwrt-kirkwood-linksys-viper-squashfs-sysupgrade.tar
The factory.bin image can be flashed from the Linksys interface. Upgrading between OpenWrt images is done with the sysupgrade.tar image. If firmware installation fails on linksys firmware, try renaming the file to .img extension.

There seems to be a wifi driver bug.
https://dev.openwrt.org/ticket/21284

Router Model: linksys wrt160n v3
Link to Openwrt wiki: https://wiki.openwrt.org/toh/linksys/wrt160n
Is it supported in Openwrt? Yes
Does it have >= 4MB of flash? No
Does it have >= 8MB of flash? No
Does it have USB support? No

since it does not have greater than 4MB flash personally i'm ok with unstable, or older versions or etc. just looking for any chance to get Gargoyle.

below is the link that i found OpenWrt firmware for this router that were installed on my wrt160n v3.
openwrt-wrt160n_v3-squashfs.bin

Thank You


Notes from Lantis:
Rejected - 4MB

tapper wrote:

dlogictech wrote:Router Model: Linksys WRV54G
Link to Openwrt wiki: https://wiki.openwrt.org/toh/linksys/wrv54g
Is it supported in Openwrt? Yes
Does it have >= 4MB of flash? Yes
Does it have >= 8MB of flash? Yes
Does it have USB support? No

Hi there mate due to the slow CPU i dont think Gargoyle will run verry well for this router. I had a wrt54g overclocked to 333 MHZ and it was frustratingly slow and crashed a lot.

Hi Tapper,
I appreciate the comment, but this router is currently gathering dust on my shelf as it is and I really would like to make use of it.
I ask for a Gargoyle build so I can have another router to play around with and provide feedback.
If you guys are willing to build it I will provide valuable feedback.
At the very least we all will know how it performs.

Lantis wrote:Do you own all of these?

Yes I do own all of these routers, and I am eager to flash Gargoyle on them.