Gargoyle Forum

Upgraded DIR-505E A2 from Gargoyle 1.7.0 to 1.7.1. Didn't attempt to preserve settings.

All's working fine and looking normal. Tested guest network, works nicely. Great addition, big thumbs up.

*update*: Sucessfully applied the reghack patch. Channels 12 and 13 showing as expected.

durian wrote:This is the error message i get in Safari:
Safari can't open the page
Too many redirects occurred trying to open “http://192.168.1.1/overview.sh”. This might occur if you open a page that is redirected to open another page which then is redirected to open the original page.

Chrome works fine

You might want to check this workaround:
http://www.gargoyle-router.com/phpbb/vi ... ari#p27472

lceron80 wrote:upgrade on my wndr3800 went smoothly. i couldn't get internet access after upgrading. reflashed and still the same connectivity issue. went back to 1.6.x and the issue resolved itself. is there anything i can do to troubleshoot and pin point why i cannot get internet access with this update

I made the upgrade from v1.5.11 to v1.7.1 on my TP-Link WR841ND V7 router. I made the configuration, all thing seems ok. But the router couldn't connect to the internet... PPPoE mode, and Connection on demand... It isn't working, I try evereything.
Than I changed the connection mode to "Keep alive", and the router can connected to the internet. (Now working in this mode.) If I switch back to Connetion on demand mode, the router can't connet. So I think it is program/firmware fail in this version (1.7.1.). I think in the previous version worked both.

Is anyone with a very fast connection (100Mbps+) getting bottlenecked by the BB builds? I was fortunate enough to have my speed increased recently, and I was measuring 110Mbps in AA at Speedtest. In the BB builds I've tried (1.7.0 and 1.7.1, plus another Ispy build or two in between), I get only 86-90Mbps.

The only thing I can figure, unless BB just doesn't play nice with my router (WZR-HP-G300NH), is that maybe the WAN connection is falling back to 100Mbps instead of gigabit, and the reduced speed is from the overhead.

SirDrexl wrote:Is anyone with a very fast connection (100Mbps+) getting bottlenecked by the BB builds? I was fortunate enough to have my speed increased recently, and I was measuring 110Mbps in AA at Speedtest. In the BB builds I've tried (1.7.0 and 1.7.1, plus another Ispy build or two in between), I get only 86-90Mbps.

The only thing I can figure, unless BB just doesn't play nice with my router (WZR-HP-G300NH), is that maybe the WAN connection is falling back to 100Mbps instead of gigabit, and the reduced speed is from the overhead.

Hi it has to do with hardwair nat.
some chatter about it here:
https://forum.openwrt.org/viewtopic.php?id=51726

Actually it's about a cache option that was available in AA, removed in BB, and repatched in for CC but then not back ported.
I may suggest it to Eric for the next build. I'd have to find the relevant documentation again though.

EDIT: the link you posted is the exact thread i was talking about lol.
this is the relevant trunk changeset, it would be nice to backport to BB but don't know if it's priority.
https://dev.openwrt.org/changeset/43587/trunk

governa wrote:

durian wrote:This is the error message i get in Safari:
Safari can't open the page
Too many redirects occurred trying to open “http://192.168.1.1/overview.sh”. This might occur if you open a page that is redirected to open another page which then is redirected to open the original page.

Chrome works fine

You might want to check this workaround:
http://www.gargoyle-router.com/phpbb/vi ... ari#p27472

It works, thanks!!!

Upgraded from 1.7.0, TL-WR841N v9, din't preserve settings, all working good so far.

TP-link 1043ND V1

I tried to preserved setting, bricked.
Then I recovered router by TTL, flashed gargoyle .bin firmware through TFTP directly.
I unbrick router successfully.
I don't know why people tend to flash openwrt then flash to Gargoyle.
It is possible to flash to Gargoyle by one step.

Hello, I' m using tp-link 3600 v1.1 and guest network isolation not working.
I can see and connect to any computers over Guest network.
How can I properly setup guest network isolation.
Thanks