Re: 3g support
Posted: Wed Jan 05, 2011 6:08 pm
Thanks
Will try right now
Gargoyle Forum
A forum to discuss the Gargoyle web interface for Openwrt
https://www.gargoyle-router.com/phpbb/
3g support
Page 2 of 4
Re: 3g support
Posted: Wed Jan 05, 2011 6:10 pm
Re: 3g support
Posted: Wed Jan 05, 2011 6:51 pm
Things are looking good but not perfect
This is my telco settings
This is what I get when I plug my usb modem in (which looks good)
Soon after this the router locked up
Look like I might have to try again with a reflash
This is my telco settings
Code: Select all
APN = internet.telecom.co.nz
username = (blank)
password = (blank)
Dial Number = *99#
PDP Type = IP
Authentication Mode = PAP
DNS Server = Obtain Automatically
PDP Address = Obtain AutomaticallyCode: Select all
usb 1-1: new high speed USB device using ar71xx-ehci and address 3
usb 1-1: configuration #1 chosen from 1 choice
option 1-1:1.0: GSM modem (1-port) converter detected
usb 1-1: GSM modem (1-port) converter now attached to ttyUSB0
option 1-1:1.1: GSM modem (1-port) converter detected
usb 1-1: GSM modem (1-port) converter now attached to ttyUSB1
scsi1 : SCSI emulation for USB Mass Storage devices
option 1-1:1.3: GSM modem (1-port) converter detected
usb 1-1: GSM modem (1-port) converter now attached to ttyUSB2
usb-storage: device found at 3
usb-storage: waiting for device to settle before scanning
scsi 1:0:0:0: Direct-Access ZTE MMC Storage 322 PQ: 0 ANSI: 2
usb-storage: device scan complete
sd 1:0:0:0: [sdb] Attached SCSI removable diskLook like I might have to try again with a reflash
Re: 3g support
Posted: Wed Jan 05, 2011 7:32 pm
I got it to work
YES
Required Changes
and
Edit /etc/chatscripts/3g.chat, modify apn to:
as per
https://forum.openwrt.org/viewtopic.php?id=26045
Big thanks Guys
YES
Required Changes
Code: Select all
/dev/ttyUSB2Edit /etc/chatscripts/3g.chat, modify apn to:
Code: Select all
OK 'AT+CGDCONT=1,"IP","$USE_APN","",0,0'https://forum.openwrt.org/viewtopic.php?id=26045
Big thanks Guys
Re: 3g support
Posted: Thu Jan 06, 2011 1:04 am
Been running for up for 5 hours now with good results
I think there is something wrong with the "connection attempts" but once connected works well.
Signal strength is poor and I suspect this has something to do with poor connection attempts?
I've been waiting for it to fail to post the logread but nothing to report so far
I think there is something wrong with the "connection attempts" but once connected works well.
Signal strength is poor and I suspect this has something to do with poor connection attempts?
I've been waiting for it to fail to post the logread but nothing to report so far
Re: 3g support
Posted: Thu Jan 06, 2011 2:18 am
I know I'm not using an official build but i want to report anyway
If you change the SSID the router will lock up
To reset I removed the power
Router rebooted as expected but would not connect to the internet
SSH into router and ran "ifup wan" command which connected to the internet.
Router running fine after that.
This build is very touchy
If you change the SSID the router will lock up
To reset I removed the power
Router rebooted as expected but would not connect to the internet
SSH into router and ran "ifup wan" command which connected to the internet.
Router running fine after that.
This build is very touchy
Re: 3g support
Posted: Thu Jan 06, 2011 6:02 am
try in ssh:
uci set network.wan.auto=1
uci commit
ifup wan
then wan up at boot automaticly(until do some changes in Gargoyle GUI
)
uci set network.wan.auto=1
uci commit
ifup wan
then wan up at boot automaticly(until do some changes in Gargoyle GUI
)Re: 3g support
Posted: Sun Feb 06, 2011 7:43 pm
will it work on TP-Link 1043 ???
Re: 3g support
Posted: Mon Feb 07, 2011 3:16 pm
no
Re: 3g support
Posted: Mon Feb 07, 2011 3:33 pm
please make any gargoyle build with built in support 3g modems for Tp-Link 1043 (DD-WRT 3G support is very unstable ) i have many modems and test it ( E219 , E1550 , E173 and E1823)